YASKAWA A1000 HHP Programming Manual page 262

A.8 F: Options
No.
(Addr. Name
Hex)
F1-10 Excessive Speed Deviation
(389) Detection Level
F1-11 Excessive Speed Deviation
(38A) Detection Delay Time
F1-12
PG 1 Gear Teeth 1
(38B)
F1-13
PG 1 Gear Teeth 2
(38C)
F1-14 PG Open-Circuit Detection
(38D) Time
F1-20 PG Option Card Disconnect
(3B4) Detection 1
F1-21
PG 1 Signal Selection
(3BC)
F1-30 PG Card Option Port for
(3AA) Motor 2 Selection
F1-31
PG 2 Pulses Per Revolution
(3B0)
F1-32
PG 2 Rotation Selection
(3B1)
F1-33
PG 2 Gear Teeth 1
(3B2)
F1-34
PG 2 Gear Teeth 2
(3B3)
F1-35 PG 2 Division Rate for Pulse
(3BE) Monitor
F1-36 PG Option Card Disconnect
(3B5) Detection 2
262
V/f V/f V/f w PG V/f w PG V/f w PG V/f w PG OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM CLV/PM CLV/PM
Sets the speed deviation detection level as a percentage of the maximum output
frequency.
V/f V/f V/f w PG V/f w PG V/f w PG V/f w PG OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM CLV/PM CLV/PM
Sets the time in seconds for a speed deviation situation to trigger a fault (dEv).
V/f V/f w PG V/f w PG OLV
OLV/PM AOLV/PM CLV/PM
Sets the gear ratio between the motor shaft and the encoder (PG).
A gear ratio of 1 will be used if F1-12 or F1-13 are set to 0.
V/f V/f w PG V/f w PG OLV
OLV/PM AOLV/PM CLV/PM
Sets the gear ratio between the motor shaft and the encoder (PG). A gear ratio
of 1 will be used if F1-12 or F1-13 are set to 0.
V/f V/f V/f w PG V/f w PG V/f w PG V/f w PG OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM CLV/PM CLV/PM
Sets the time required to trigger a PG Open fault (PGo).
V/f V/f V/f w PG V/f w PG V/f w PG V/f w PG OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM CLV/PM CLV/PM
0: Disabled
1: Enabled
V/f V/f w PG V/f w PG OLV
OLV/PM AOLV/PM CLV/PM
0: A pulse detection
1: AB pulse detection
V/f V/f V/f w PG V/f w PG V/f w PG V/f w PG OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM
Sets the port for the PG option card used by motor 2.
0: CN5-C
1: CN5-B
V/f V/f V/f w PG V/f w PG V/f w PG V/f w PG OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM
Sets the number of pulses for a PG option card connected to port CN5-B.
V/f V/f V/f w PG V/f w PG V/f w PG V/f w PG OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM
0: Pulse A leads
1: Pulse B leads
V/f V/f w PG V/f w PG OLV
OLV/PM AOLV/PM CLV/PM
Sets the gear ratio between the motor shaft and the encoder (PG).
A gear ratio of 1 will be used if F1-33 or F1-34 are set to 0.
V/f V/f w PG V/f w PG OLV
OLV/PM AOLV/PM CLV/PM
Sets the gear ratio between the motor shaft and the encoder (PG). A gear ratio
of 1 will be used if F1-33 or F1-34 are set to 0.
V/f V/f V/f w PG V/f w PG V/f w PG V/f w PG OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM
Sets the division ratio for the pulse monitor used of the PG option card 2
installed to port CN5-B.
By setting "xyz", the division ratio becomes = [(1 + x) / yz].
V/f V/f V/f w PG V/f w PG V/f w PG V/f w PG OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM
0: Disabled
1: Enabled
YASKAWA ELECTRIC SIEP YEAHHP 01B YASKAWA AC Drive – A1000 HHP Programming Manual
Description
CLV CLV CLV CLV
CLV CLV CLV CLV
CLV
CLV
CLV CLV CLV CLV
CLV CLV CLV CLV
CLV
CLV CLV CLV CLV
CLV CLV CLV CLV
CLV CLV CLV CLV
CLV
CLV
CLV CLV CLV CLV
CLV CLV CLV CLV
Values Page
Default: 10%
Min.: 0 85
Max.: 50
Default: 0.5 s
Min.: 0.0 85
Max.: 10.0
Default: 0
Min.: 0 85
Max.: 1000
Default: 0
Min.: 0 85
Max.: 1000
Default: 2.0 s
Min.: 0.0 84
Max.: 10.0
Default: 1
86
Range: 0, 1
Default: 0
86
Range: 0, 1
Default: 1
86
Range: 0, 1
Default: 1024 ppr
Min.: 1 84
Max.: 60000
Default: 0
85
Range: 0, 1
Default: 0
Min.: 0 85
Max.: 1000
Default: 0
Min.: 0 85
Max.: 1000
Default: 1
Min.: 1 85
Max.: 132
Default: 1
86
Range: 0, 1