Settings - Siemens siprotec SJ62 User Manual

2 Functions

2.12.7 Settings

Addr. Parameter
3101 Sens. Gnd Fault
3102 CT Err. I1
3102 CT Err. I1
3103 CT Err. F1
3104 CT Err. I2
3104 CT Err. I2
3105 CT Err. F2
3106 VPH MIN
3107 VPH MAX
3108 64-1 VGND
3109 64-1 VGND
3110 64-1 VGND
3111 T-DELAY Pickup
3112 64-1 DELAY
3113 50Ns-2 PICKUP
3113 50Ns-2 PICKUP
3114 50Ns-2 DELAY
3115 67Ns-2 DIRECT
3117 50Ns-1 PICKUP
3117 50Ns-1 PICKUP
3118 50Ns-1 DELAY
3119 51Ns PICKUP
217
Addresses which have an appended "A" can only be changed with DIGSI, under "Dis-
play Additional Settings".
The table indicates region-specific default settings. Column C (configuration) indicates
the corresponding secondary nominal current of the current transformer.
C Setting Options
OFF
ON
Alarm Only
0.001 .. 1.600 A
1A 0.05 .. 35.00 A
5A 0.25 .. 175.00 A
0.0 .. 5.0 °
0.001 .. 1.600 A
1A 0.05 .. 35.00 A
5A 0.25 .. 175.00 A
0.0 .. 5.0 °
10 .. 100 V
10 .. 100 V
1.8 .. 200.0 V
1.8 .. 170.0 V
10.0 .. 225.0 V
0.04 .. 320.00 sec; ∞
0.10 .. 40000.00 sec; ∞
0.001 .. 1.500 A
1A 0.05 .. 35.00 A
5A 0.25 .. 175.00 A
0.00 .. 320.00 sec; ∞
Forward
Reverse
Non-Directional
0.001 .. 1.500 A
1A 0.05 .. 35.00 A
5A 0.25 .. 175.00 A
0.00 .. 320.00 sec; ∞
0.001 .. 1.400 A
Default Setting
OFF (Sensitive) Ground Fault
0.050 A Current I1 for CT Angle
Error
1.00 A Current I1 for CT Angle
Error
5.00 A
0.0 °
CT Angle Error at I1
1.000 A Current I2 for CT Angle
Error
10.00 A Current I2 for CT Angle
Error
50.00 A
0.0 °
CT Angle Error at I2
40 V L-Gnd Voltage of Faulted
Phase Vph Min
75 V L-Gnd Voltage of Unfault-
ed Phase Vph Max
40.0 V 64-1 Ground Displace-
ment Voltage
40.0 V 64-1 Ground Displace-
ment Voltage
70.0 V 64-1 Ground Displace-
ment Voltage
1.00 sec Time-DELAY Pickup
10.00 sec 64-1 Time Delay
0.300 A 50Ns-2 Pickup
10.00 A 50Ns-2 Pickup
50.00 A
1.00 sec 50Ns-2 Time Delay
Forward 67Ns-2 Direction
0.100 A 50Ns-1 Pickup
2.00 A 50Ns-1 Pickup
10.00 A
2.00 sec 50Ns-1 Time delay
0.100 A 51Ns Pickup
SIPROTEC 4, 7SJ62/63/64 Handbuch
C53000-G1140-C147-A, Edition 07.2015
Comments