Mitsubishi PLK-E Series Technical Manual page 206

Program mode list
[17] Program mode list
Changing to the program mode
When using the LCD panel, refer to the section " Operation panel section[16] Program mode ". When using the 7-segment operation
panel keys, refer to pages " Control unit section[8]-3 to [8] -4".
* For item (*1), there is no LCD panel program mode item. Change to each mode using the 7-segment operation panel keys. Depending
on the item, the other LCD panel functions can be operated. (For example, [O1L] in the "output signal" item can be operated from the
"input/output setting mode".)
Wiper
WIP Wiper ON/OFF
W1 Wiper output (W) output start time
W2 Wiper output (W) output time
Slow start
S Slow start speed
SL Slow start setting
SLN Number of slow start stitches
Clamp
Start/stop even if work holder is not
OST
lowered
RPT Repeat sewing setting
RP(1-8) Work holder 1-8 repeat sewing setting
WHY Work holder order of priority setting
FSR All cancel during step over operation
1PD 1-pedal specification setting
1T 1-pedal timer setting
(1-8)A Work holder 1-8 ON delay timer setting
Work holder 1-8 OFF delay timer
(1-8)B
setting
OFB Number of Work holder division setting
FN Number of rated Work holder setting
CF Work holder sequence setting
Valid Work holder number setting for
F21N
divided Work holder (OF1...OF4)
Valid Work holder number setting for
F22N
divided Work holder (OF5...OF8)
Work holder sequence setting for
CF1
divided Work holder (OF1...OF4)
Work holder sequence setting for
CF2
divided Work holder (OF5...OF8)
Valid number setting of Work holder
F4BN
blocks
F4SN Number of block steps setting
Pneumatic type two stage work holder
AF2
selection
Sewing area
ALC Sewing area limit cancel
XL [X axis left side] area limit setting
XR [X axis right side] area limit setting
[Y axis back side] area limit
YU
modification
[Y axis front side] area limit
YD
modification
Needle position
Reverse run needle UP function after
RU
thread trimming
R8 RU reverse angle setting
U8 Needle UP position stop angle
D8 Needle DOWN position stop angle
Bobbin winding
W Bobbin winding speed
WSM Bobbin winding operation setting
WT Bobbin winding operation time
Table explanation
[ ]
type
[ symbol ] [ function name ]
4(1)
B33
B34
B43
B44
B45
G40
G1
G(2-
9)
G10
G11
G12
G13
G(14
-21)
G(22
-29)
G30
G31
G32
G33
G34
G35
G36
G37
G38
G39
A1
X5
X6
X7
X8
B5
B6
B7
B8
B46
B47
B48
[mode]
Home position
HPM Home position return method at HALT
Home position return prohibit at power
HPC
ON
Automatic home position return
HPF
operation prohibition
HPK Reset key setting
Temporary stop method at secondary
2HS
home position
FHP Free home position usage method
Home position correct selection at
CHS
sewing data read
[X axis] limit sensor home position
SHX
return
SHY [Y axis] limit sensor home position return
Setting for presser foot state of home
HPS
return operation after power ON
HALT
Feed data stop state at HALT switch
STF
operation
Needle stop state at HALT switch
STN
operation
Various output hold at HALT switch
STS
operation
ST2 HALT switch two-press operation
Power operation at HALT switch
STP
operation
Work holder raise operation when
STD
stopped with HALT code
STL Double-drop prevention after HALT
Counter
CUP Increment (UP) counter function
CDN Decrement (DN) counter function
Increment (UP) counter setting value
UCM
clear method
Decrement (DN) counter setting value
DCM
clear method
PCM Counter clear method at power ON
CN Number of stitches count function
Increment (UP) counter count value
UCC
correction prohibit
Decrement (DN) counter count value
DCC
correction prohibit
Sewing work with increment (UP)
USC
counter
Sewing work with decrement (DN)
DSC
counter
Brakes
WBK Weak brake setting
BKM Weak brake function setting
BNR Weak brake noise setting
BKT Brake time setting
Weak brake operation time during
PW
presser bar lifting operation
Presser foot
Presser bar lifting timer 1 (lowering)
PD
setting
PU Presser bar lifting timer 2 (rising) setting
UW Presser bar lifting timer 3 (rising) setting
Setting of presser foot when baste is
BPF
sewn and the feed moves
A10
A11
A12
A14
A15
A16
A17
X9
X10
A13
A2
A3
A4
A5
A7
A8
A9
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
B1
B2
B3
B4
X23
B35
B36
B37
B26