AGFA Avantra 36/44 Service Manual page 276

Motor, Beam Compressor 4-52
Motor, DC Spindle A/B Gear 2-26
Motor, Focus Changer Stepper 2-11
Motor, Supply Drive Servo 4-58
Motor, Weak Lens 4-54
Motors
aperture wheel 2-16, 4-50, 4-51, 4-53, 4-54
beam compressor 2-16, 4-50, 4-52, 4-53
polarizer 2-16, 4-50
spin 4-47
supply cassette A and B 4-61
supply drive servo 4-58
weak lens 2-16, 4-50, 4-54
Motors, Rewind 2-26
N
New Engine/Restart 3-44
New Engine/Restart Command 3-44
Nip Delay
definition 3-33
range 3-33
Nip Solenoid Connector
location 4-10
Nips Op Ely Time
definition 3-34
O
OCP 2-5, 2-8, 2-10, 2-14, 3-3, 3-4, 3-19, 3-36,
3-37
application firmware 3-4
OCP EEPROM 3-36, 3-37
OCP Error Reporting 3-5
OCP FLASHROM 2-9, 3-54
OCP Micro-controller Test Descriptions 3-11
OCP Micro-controller Tests
display controller 3-11
display RAM 3-11
external ROM checksum 3-11
OCP Micro-Controller's EEPROM 3-52
OCP Module 2-4
OCP PC Board 2-4
OCP Register Test 3-7
OCP Tests 3-23
OCP User Parameters 3-36
Offgate Register Test 3-6
Offset Values 5-14
OLP 2-9
OLP Interface 2-10
Ongate Register Test 3-6
On-Line Processor (OLP) Specifications 1-3
Open Log File 3-24
Operational Inspection 6-4
Operational Statistics 3-37, 3-52
Operator Control Panel (OCP) 2-8, 3-3
power supply connector
location 4-31
ribbon cable
location 4-31
Operator Control Panel Assembly
remove and replace 4-30
remove/replace 4-30
Operator's Control Panel (OCP) User Parame-
ters
save/restore 3-52
Optic Pads 6-3
Optical System
spin motor module 2-15
spot generation module 2-15
Optical System Overview 2-15
Opto-mechanical Removal/Replacement
Procedures 4-45
Outer Channel Bolts 1-9
Outer Take-up (Nip) Assembly
location 4-10
Outer Take-up Drive (Nip) Assembly
remove and replace 4-10
Outer Take-up Drive Assembly
remove/replace 4-10
Overview, Linear Carriage Transport 2-19
Overview, Media Transport System 2-25
P
Packaging, Electronics 2-4
Packing Materials 1-14, 1-15
Parameters
cassette 3-37, 3-52
DSP 3-49
Image/Focus 3-49
Media 3-49
OCP user 3-36, 3-52
user 3-52
Parts List 1-6
Parts List Package 1-7
PC Board 2-4
PC Imager software 3-2
PC Imager User's Manual 3-2
PC Requirements
for running AVDIAG 3-17
Phase Lock Loop Verification 3-10
Physical Specifications
image setter 1-3
Plastic Inserts 1-14
Polarizer 2-17
Polarizer Home Sensor 2-11
Polarizer Rotation Sensor
remove and replace 4-51
Polarizer Sensor
location 2-16, 4-50, 4-52
Polarizer Stepper Motor 2-10
Polarizer Wheel
location 2-16, 4-50
Port Configuration 3-44
Port Test 3-10
Positioning the Jack Screw 1-10
Power Consumption 1-1
Power Distribution 2-14
Power Requirements 1-1
Power Supply 2-14
remove and replace 4-34
Section I: Imagesetter
Index I-7