Christie CP2000 User Manual
  1. Manuals
  2. Brands
  3. Christie Manuals
  4. Projector
  5. CP2000
  6. User manual

Christie CP2000 User Manual

Hide thumbs Also See for CP2000:
Table of Contents

Advertisement

Quick Links

See also: Setup Manual
CP2000
U S E R ' S M A N U A L
020-100032-04

Advertisement

Table of Contents
loading

Related Manuals for Christie CP2000

Summary of Contents for Christie CP2000

  • Page 1 CP2000 U S E R ’ S M A N U A L 020-100032-04...
  • Page 2 X: indicates that the concentration value of the particular hazardous substance contained in all the homogeneous materials for this part, according to EIP-A, EIP-B, EIP-C, may be above the stipulated levels in China SJ/T11363-2006. 表示该有毒有害物质至少在该部件的某一均质材料中的含量可能超出SJ/T11363-2006规定的限量要求。 * This part uses metallic alloys, which may contain Lead. 因该部件使用金属合金材料，故可能含有铅。 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)

  • Page 3: Table Of Contents

    5.1 Compatible Non-Cinema Sources ................5-1 5.2 Selecting the Source ....................5-3 Non-Cinema Operation 6.1 Warnings and Guidelines ................... 6-1 6.2 Maintaining Proper Cooling ..................6-3 Maintenance 6.3 Maintenance & Cleaning ................... 6-4 LIT MAN USR CP2000 (Software v2.7) 020-100032-04 Rev. 1 (03/14)

  • Page 4: Table Of Contents

    C Serial Communications Cables ................... C-1 D GPIO System Integration .................... D-1 E Repacking the Projector ....................E-1 Due to continuing research, all information in this manual is subject to change without notice. LIT MAN USR CP2000 020-100032-04 Rev.1 (03/14)

  • Page 6: The Projector

    Introduction The content of this manual applies to the following products only: CP2000i models CP2000h models CP2000-S* models - See also enclosed addendum for CP2000-S ballast configuration and additional specifications.  The CP2000 is a professional quality, easy-to-use DMD projector utilizing Digital ...

  • Page 7: List Of Components

    CP2000 models differ in their power level—the CP2000h and CP2000 Models CP2000-S offers higher power for the largest venues, whereas the CP2000i offers intermediate power for smaller venues. Before installation, make sure you have the correct pedestal for your region, installation, and CP model: In North America* or Japan (180-235 VAC 3-phase, 100-120 VAC single-phase) •...

  • Page 8: Purchase Record And Service Contacts

    Should you encounter a problem with any part of the projector and require assistance, contact your dealer or one of the Christie service depots listed on the back cover of this manual. In most cases, CP servicing is performed on site. If you have purchased the projector, fill out the information on the following page and keep with your records.

  • Page 9: Who Should Use This Manual?

    SERVICE: Only trained and qualified Christie service technicians knowledgeable about all potential hazards associated with high voltage, ultraviolet exposure and high temperatures generated by the lamp and associated circuits are authorized to 1) assemble/install the projector and 2) perform service functions inside product enclosures.

  • Page 10: Servicing Live Equipment

    NOTES: 1) Illustrations apply to most CP models, unless otherwise specified, and may not always include the rear- mount TPC. 2) The CP2000-S model does not include the internal convenience outlet as shown in some of the illustrations. Refer to the separate CP2000-S Addendum for additional installation information.

  • Page 11: Assembly And Connection Of Components

    • Latex lab gloves • Lens cleaning tissue and solution (see 6.3, Maintenance & Cleaning) • For CP2000-S Models – Refer to the Addendum for Installation and Use provided. Projection Head  1) Secure projection head to pedestal and Pedestal WARNING •...
  • Page 12 Secure head-pedestal assembly with 4 washers/nuts tightened snugly on to the 4 threaded rods (use ¾” wrench). 2) Position CP2000 at port window Roll the projector until its base is approximately 2 feet from the port window wall, 3 feet if anamorphic lens mount will be added (optional). Center with the theatre screen () if possible (see Figure 2.2A).

  • Page 13: Adjusting Tilt And Leveling

    Numerous cables are pre-installed within the pedestal and must be routed up to the underside of the projection head, where they connect to one of three panels (or two IEC power sockets). Connect pedestal-to-head cabling as follows: LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)

  • Page 14: Lamp

    NOTE: These cables also connect to the fire alarm interlock and dedicated outlet (both pre-connected at manufacture). 5-5) POWER CABLES TO HEAD: From behind the main AC breaker panel (within the pedestal), connect both identical power cables 34-001992 to LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)

  • Page 15: Ethernet

    (200-230 VAC). These cables are interchangeable—connect either cable to either receptacle, and secure with metal strain-relief clip provided. See Figure 2.7. NOTE: For CP2000-S Models – Refer to the Addendum for Installation and Use provided. Figure 2.7. Connect “Projector” Breaker Power Cables to Projection Head...
  • Page 16 ¾” from the high-voltage terminal (with braid connection). • Route all igniter wires AWAY from 9-pin and 15-pin connectors. • Twist both ballast cables twice-per-foot • Close and lock the igniter door. LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 17 1.658” in overall length. See right. NOTE: The universal nut shown accommodates all models. Do not Figure 212. Connector Nut install a shorter nut. LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 18 (see Figure 2.14). Looking into the pedestal, the liquid will circulate counterclockwise. Shown for pedestals manufactured before Fall 2006 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)

  • Page 19: Initial Power-Up

    Avoid “forcing” together, and listen for “click”. 7) Fill the reservoir completely (initial filling for hoses only) After connecting the hoses, completely fill the cooler reservoir with Christie’s 50/50 mix of distilled water and ethylene glycol. For this first filling, simply fill the reservoir completely—there is no need to...
  • Page 20 Confirm that 1) there are no obstructions or “kinks” within the ducting, 2) all air intake areas of the CP2000 are clear and exposed, and 3) the vane switch at the exit duct is moving freely. The pre-installed outside-venting duct should be rigid at the projector,...
  • Page 21 * For this projector, the 2.0 kW is available in CDXL (maximum performance) only ** Available as CDXL (maximum performance) or original CXL (less expensive). Refer to full specifications in Section 8. 2-12 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 22 See 6.4, Replacing the Lamp & Filter, Steps 7-10. Observe all warnings, and wear protective clothing and shielding. Connecting to Power  For CP2000-S Models – Refer to the Addendum for Installation and Use provided. Before connecting to AC, configure the lamp ballast to match the AC available at the site.
  • Page 23 WARNING Connect ground FIRST to reduce shock hazard from high leakage. Figure 2.17. Connect Incoming Ground Wire (shown for pedestals manufactured prior to November 17, 2006) 2-14 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 24 Attach no other wires here. o Connect 1, 2, and 3 @ 180-235 VAC (3-phase) o No L or N available, so the internal outlet will not be functional. LIT MAN USR CP2000 2-15 020-100032-04 Rev. 1 (03/14)
  • Page 25 (as it is for most countries). If you find your incoming AC is below 207 VAC, connect terminal jumper to instead. • If AC between terminals is 207-265, connect terminal (factory default). • If AC between terminals is 180-207, connect terminal Refer to Figure 2.20. 2-16 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 26 • If your measurement at the 115V terminal is 103.5V or less , move the 115V +10%. wires to the tap labeled Figure 2.20. Check Voltage Between 115V and Common (“0V”) LIT MAN USR CP2000 2-17 020-100032-04 Rev. 1 (03/14)
  • Page 27 Changing or adding a source connection requires access via the locked CP pedestal. NOTE: The illustrations in this section are of the CP2000. CP2000-S models do not include an internal outlet. IF EXTERNAL : Source/server cabling routes through the pedestal toe and up to the underside of the projection head.
  • Page 28 : Sources/servers are often rack-mounted in the projector rear, with cabling routed directly to the underside of the projection head—see Figure 2.24 and Figure 2.25 (shown are CP2000 models with internal outlet for North America, etc. Not applicable to CP2000-S. Refer to the separate CP2000-S Addendum for more information).
  • Page 29 Depending on the installation, you may also need certain other serial Communications and/or Ethernet links to the CP2000, such as from a server or PC functioning as a controller, or from an existing on-site network including other equipment.
  • Page 30 Adjusting Tilt and Leveling In an ideal installation, the CP2000 lens surface is centered with and parallel to the screen—this orientation helps to ensure optimized lens performance with minimal offset (Figure 2.27). If this position is not possible (such as when the projector is significantly higher than the center of the screen), it is better to rely on offset rather than extra tilt.
  • Page 31 Figure 2.28. Open rear of pedestal 6. On each side of the rear opening in the pedestal, loosen the 2 bolts securing the rear extender legs to the projector. See Figure 2.30. 2-22 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 32 Upon initial power up, your first supply of coolant will drain into the hoses and fill them, leaving the reservoir itself almost empty. Using Christie’s 50/50 mix of distilled water and ethylene glycol, re-fill the reservoir until the level is close to but not above the top mark on the gauge located on the outside of the pedestal door (see right).

  • Page 33: Maximizing Light Output

    At this point, light output is optimized.  NOTE: Lamp must be on and douser (shutter) open during LampLOC adjustment, however the projector does not need to be displaying an image. 2-24 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)

  • Page 34: Basic Image Alignment

    NOTE: Before you begin:  The CP2000 must be properly positioned relative to the screen (refer back to Figure 2.2 and Figure 2.27). Basic Optical Alignment Procedure 1. Display a good test pattern appropriate for analyzing image focus and geometry, such as a single crosshair centered across the image.

  • Page 35: Cinema Displays

    Always adjust offset before boresight. NOTE: For best optical performance, make sure to minimize offsets by “aiming” the projector lens at the center of the image. Refer back to Figure 2.2. Figure 2.35. Offsets 2-26 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 36 Hold a piece of white paper approximately parallel to the screen surface at the right side (and as close to the vertical center as possible), then move closer to the projector while watching the image on the paper. LIT MAN USR CP2000 2-27 020-100032-04 Rev. 1 (03/14)
  • Page 37 Figure 2.40. Adjust Top Focus bottom of the image is focused in front of the screen or behind the screen. If the bottom is well-focused, skip to Step 11. 2-28 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)

  • Page 38: Fold Mirror And Convergence Adjustments

    Qualified service technicians can correct as described on the color label provided inside the projection head. LIT MAN USR CP2000 2-29 020-100032-04 Rev. 1 (03/14)

  • Page 39: Calibrating The System Using Dcp Librarian Setup Software

    DCP Librarian also defines the system/network configuration for communication links to the projector, transmitting information to and from the CP2000 via an Ethernet or RS-232 connection. Chief functions, many of which can be done at the TPC, are introduced below.

  • Page 40: Phase Balancing

    Once the collected settings are downloaded to the projector’s internal memory, their “PCF” can be assigned to the corresponding CP2000 input connection and quickly applied via a controller such as Christie’s Touch Panel Controller. No further adjustment in processing should be required.

  • Page 42: Projector Basics

    Basics technician as described in Section 2, Installation and Setup. Components/Features  Chief CP2000 components appear on the following page. See page 3-2. LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 43 BASIC OPERATION Figure 3.1. Basic Projector and Related Components LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 44 Each circuit breaker on the pedestal serves two purposes: 1) it is a power switch for one or more components, and 2) it protects against over-current conditions. All breakers must be ON for normal CP2000 power-up and operation, enabling AC to reach the CP components If faulty or excessive AC is detected, a breaker will “trip”...
  • Page 45 TPC and the Ethernet hub, and is powered by the 3- phase main AC breaker on the operator’s side of the projector. Do not plug in other CP2000 system components such as servers or controllers. CONVENIENCE OUTLET: External equipment used with the projector, such as rack- mounted servers, controllers, etc., can plug into the internal standard convenience...
  • Page 46 Christie key fob, and cannot be duplicated. If you lose or damage a key, contact your dealer or Christie for a new security lock and key set—...
  • Page 47 (internal, underside of projection head) The Source and Communication Connection Panel provides high-security connection of the CP2000 to a variety of external equipment such as sources and controllers: • ETHERNET: Connect networked equipment such as PCs and servers to the internal Ethernet hub.

  • Page 48: Power-Up Procedure

    1. Make sure that the breakers at the main wall panel for the CP are switched 2. At the operator’s side of the pedestal, set all CP2000 circuit breakers to —these are main AC (3-phase), the projection head (2-phase), and internal outlets MAIN AC (single-phase).

  • Page 49: Power-Down Procedure

    3. At the operator’s side of the pedestal, set all breakers to NOTE: Manual shut-down only. Optional automation not yet available from Christie. Figure 3.3. Power-down Procedure Most users will use the Touch Panel Controller (TPC) as their main interface with Introduction to the projector.
  • Page 50 TPC, and critical lamp parameters such as installed lamp type, fan speed and light level at the screen. Installers can also establish temperature scale preference, remote access rights, test pattern access LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)

  • Page 51: Using The Touch Panel Controller

    TPC Power-Up Defaults  When the CP2000 powers up (see 3.2, Power-up Procedure), the Touch Panel Controller will begin the steps of Initializing…, Attempting to log on…, and Updating status, displaying its progress on the TPC status bar at the bottom of the screen.
  • Page 52 3) Any user beyond the General User can also choose from the complete range of test patterns offered in the password-protected Advanced menu. LIT MAN USR CP2000 3-11 020-100032-04 Rev. 1 (03/14)
  • Page 53 TPC menus. In addition, a full-screen flashing red alarm window is triggered on the TPC for such problems as failed interlocks (mandatory), over- temperature (optional), and fan problems (optional). 3-12 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 54 (SAMPLE VIEWS) NOTE: The Status:System menu shown here is available to all users. For information about the password-protected Status:Server, Status:Diag and Status:Interrogator menus, please see 3.10, Working With Servers and Diagnostics. LIT MAN USR CP2000 3-13 020-100032-04 Rev. 1 (03/14)
  • Page 55 STATUS MENU ENTRIES Source Projector Input Source connection (location) of current signal Signal Vert. Freq. Cine-IPM (not applicable for CP2000 projectors) Power On/off Input and Channel Source connection (location) and channel# Signal Hor. & Vert. Freq. of current source Standby...
  • Page 56 If a safety interlock fails, power will no longer reach the lamp (DC output is stopped), and the lamp button on the TPC Main menu will be disabled. See Table 3.2. LIT MAN USR CP2000 3-15 020-100032-04 Rev. 1 (03/14)
  • Page 57 TPC Main menu. Since most interlock alarm conditions are triggered by switches, regularly check the operation of these switch levers. 2) With interlock integrity restored, the lamp button on the TPC Main menu is automatically re-enabled. 3-16 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 58 3D material, and collect these settings into a unique channel that any user can select at the Main menu. Up to 32 channels can be defined. LIT MAN USR CP2000 3-17 020-100032-04 Rev. 1 (03/14)
  • Page 59 Generally, use non- cinema processing with DVI sources having high resolution-and-frequency combinations. See examples in Table 3.3. 3-18 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 60 NOTE: See Table 5.1 for a more complete list. IMPORTANT: Attempting to use cinema processing when the incoming DVI vertical frequency is too high can cause a TPC start-up error. Turn cinema option OFF, then cycle power off/on. LIT MAN USR CP2000 3-19 020-100032-04 Rev. 1 (03/14)
  • Page 61 * These components are part of any pre-defined PCF (Projector Configuration File) that controls image processing for a given source. When the “Use PCF” checkbox is checked (), these components disappear from the Custom menu and are protected from further change. 3-20 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 62 WHITE LINE or BLUE LINE : Select only if using a single 3D input signal in which an  embedded white or blue line at the bottom of each frame identifies left vs. right, LIT MAN USR CP2000 3-21 020-100032-04 Rev. 1 (03/14)
  • Page 63 ASSIGNED GPI : Select only if using a single 3D signal requiring a separate 3D  stereo sync input at the GPIO. NOTE: Requires single 3D input; not currently supported. 3-22 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 64 96 Hz. For any source, keep the final frame rate less than that of the projector (which is 67 Hz for full 2048 x 1080 resolution). Generally, incoming 24Hz signals can be increased by a maximum factor of 5:2—see Figure 3.13. LIT MAN USR CP2000 3-23 020-100032-04 Rev. 1 (03/14)
  • Page 65 TPC access rights. ADVANCED / PREFERENCES MENU: As shown below, the Preferences menu provides access to all test patterns as well as certain system parameters. See Table 3.7 for a complete description. 3-24 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 66 * Screen Saver Enable/disable a TPC screen saver, and set its start-up delay. NOTE: To use a unique screen saver, a user-defined .bmp must be downloaded to the TPC, replacing the default. LIT MAN USR CP2000 3-25 020-100032-04 Rev. 1 (03/14)
  • Page 67 Save button for recording in memory the serial number of a new lamp and the number of hours it has already been in use (if applicable). Figure 3.9. Advanced: Lamp History Menu Functions 3-26 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 68 User Level box directly below. From your current login, add or delete more users, assign their rights, or change the password of your current login. See details in the table below. LIT MAN USR CP2000 3-27 020-100032-04 Rev. 1 (03/14)
  • Page 69 2. Enter the desired password 3. Re-enter the new password in the Confirm PW box 4. Press Save Who is currently logged on? 1. Enter the User Menu—the User Name displayed is currently logged on. 3-28 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 70 Save current resolution, offset, and aspect ration settings as a Source file that will be accessible and applied from within the Custom menu. Restore Cancel new (unsaved) source settings of resolution/offset/aspect ratio. Test Apply current settings to the image without saving. LIT MAN USR CP2000 3-29 020-100032-04 Rev. 1 (03/14)
  • Page 71 “squeezed” image back to its original “scope” aspect ratio. For sources that are not pre-squeezed, aspect ratio can be left at “0”. Table 3.8. Pre-configured source setups ADMIN: SOURCE SETTINGS (Incoming) Resolution (Original) Aspect Ratio 3-30 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 72 Letterboxing ensures that all image data is displayed and its aspect ratio is maintained. See Letterbox Notes below. Lens Factor Define the anamorphic lens needed (1.25 for the CP2000 series) to stretch an image horizontally. Leave at “1” (default) if no anamorphic lens is needed.
  • Page 73 “black bars” (unused pixels) could then be cropped off using the cropping control. Although disabling the letterbox control also fills the defined presentation area, any extra data beyond this area—whether top-and-bottom or left- 3-32 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 74 MCGDs, naming them as desired. To use an MCGD file as the reference file for target color processing (such as with a certain source and/or lens), select it in the Custom menu. LIT MAN USR CP2000 3-33 020-100032-04 Rev. 1 (03/14)
  • Page 75 (channel) can then use any desired MCGD file as the basis for the color corrections needed for a target color. MCGD files are chosen in the Custom menu. NOTE: Once created, user-created MCGD files can be deleted only by using Christie’s licensed DCP Librarian software. 3-34 LIT MAN USR CP2000...
  • Page 76 Do not enable the tolerance box if exact color performance is more crucial than overall image brightness, such as in telecine applications. LIT MAN USR CP2000 3-35 020-100032-04 Rev. 1 (03/14)
  • Page 77 The Internet standard protocol developed to manage nodes (servers, workstations, routers, switches and hubs etc.) on an IP network. SNMP enables network administrators to manage network performance, find and solve network problems, and plan for network growth. 3-36 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 78 TPC to define these new settings in the projection head (Notes: 1) password- protected; requires a Christie installer login. 2) projector can be on the network during these changes, if desired.): 1.
  • Page 79 IP address, lamp type, and user rights for remote access and data logging. Installers can also record minimum and maximum footlambert readings to define a range from which other TPC lamp readings are 3-38 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 80 TPC. To change to a new source—i.e., a new presentation or display—do the following: • Make sure the CP2000 and TPC are both powered up and operating normally • On the Touch Panel Controller (TPC), select the Main menu tab •...
  • Page 81 For any display button on the two- page Main menu, the projector interprets incoming signal data according to one of sixteen user-selectable display setups defined at the time of CP2000 installation (and/or with each subsequent release of a new digital cinema feature) and stored in projector memory.

  • Page 82: Remote Control Of The Touch Panel Controller

    The function you wish to work with, such as channel switching or picture mute, is represented by a three-character ASCII code (A-Z, upper or lower case). This function code appears immediately after the leading “(“ that starts the message. LIT MAN USR CP2000 3-41 020-100032-04 Rev. 1 (03/14)
  • Page 83 Request by controller for picture mute status Picture mute reply from proj. (PMT!000) Reply from proj. that picture is mute is off. Set picture mute (PMT 1) Turn the picture mute on (blank the image) 3-42 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)

  • Page 84: Working With The Lamp

    These the Lamp controls are located in the Main, Advanced: Preferences, and Advanced: Lamp menus on the TPC. NOTE: For individual menu functions, see 3.5, Using the Touch Panel Controller. LIT MAN USR CP2000 3-43 020-100032-04 Rev. 1 (03/14)
  • Page 85 5120 watts (example only). Over time, however, the lamp will require more and more current in order to produce the 14 fL, until eventually the lamp wattage reaches its 6600 “overdrive” maximum, and the power to it 3-44 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 86 Lamp (kW) Lamp Current Range (amps) CP2000i/h/-S 66-80 CP2000i/h/-S 82-110 CP2000h/-S 112-135 CP2000h/-S 126-155 NOTE: A Lamp Power setting of 110 will exceed the maximum values shown here by approximately 10%. LIT MAN USR CP2000 3-45 020-100032-04 Rev. 1 (03/14)
  • Page 87 4. Repeat Steps 1-3 as necessary. 5. Repeat Steps 1-4, but reading at the screen instead of at the lens.  6. Reset Lamp Power or LiteLOC if desired. Stand-by Mode  3-46 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 88 Over time, as the theatre screen ages and dust and dirt collects on the port window, the theatre may no longer be achieving the expected footlamberts as reported by the TPC. It is a good idea to periodically recalibrate footlamberts (refer back to Figure 3.31). LIT MAN USR CP2000 3-47 020-100032-04 Rev. 1 (03/14)
  • Page 89 TPC. Zoom  With the projector in its permanent location, turn the lens zoom ring on the CP2000 primary lens to enlarge or shrink the image in each direction as necessary. Offsets  With the projector in its permanent...

  • Page 90: Working With 3D

    What Do I Need for 3D?  The CP2000 requires a 3D-capable SMPTE source and a few special hardware/software setups described here. Essentially you will connect two signals (one left eye, one right eye) to the projector, then use the TPC’s Custom:3D Control menu options to define and control the signal processing, synchronizing and output for devices used in your stereographic 3D display.
  • Page 91 RealD, for the GPIO port. 2) A pull-up power supply (not shown) is also required for the IR emitter or polarizing cell. 3) See page D-2 for cabling details. 4) No internal convenience outlet in CP2000-S. Refer to separate CP2000-S Addendum for more information.
  • Page 92 BASIC OPERATION Figure 3.19. Typical Dual-Input 3D System (CP2000 SHOWN, WITH ACTIVE GLASSES) Other Hardware Setups  Other expected hardware configurations with a single 3D source input are shown in Figure 3.45. NOTE: For future reference. Single 3D input is not currently supported...
  • Page 93 1. Connect two HD-SDI signals from a 3D media server to the projector’s SMPTE cinema ports . One carries left-eye data, the other right-eye data. Connect to either port; you will configure the projector to multiply and interleave the L/R signals properly. 3-52 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 94 3D controlling device such as an emitter or polarizer. NOTE: RealD 3D sync cable recommended. ADJUST DISPLAY, SCREEN, ETC. As desired, adjust the image color, etc. LIT MAN USR CP2000 3-53 020-100032-04 Rev. 1 (03/14)
  • Page 95 If the image seems to jump back and forth during horizontal pans, the L/R Display Sequence is likely backwards. Try reversing the current setting. Single 3D input does not work A single source signal containing both left and right data is not currently supported. 3-54 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)

  • Page 96: Working With Servers And Diagnostics

    Figure 3.23. Status:Server Menu LIT MAN USR CP2000 3-55 020-100032-04 Rev. 1 (03/14)
  • Page 97 Never run Interrogator during a show as this could cause image disruption. 3) Interrogator is also accessible through a separate login and password (different from the service login). Contact Christie tech support for assistance and password. Figure 3.25. Status:Interrogator Screen 3-56 LIT MAN USR CP2000 020-100032-04 Rev.

  • Page 98: Compatible Cinema Sources

    Section 2, Installation and Setup. Read also Section 3, Basic Operation. Make sure a digital media storage device or cinema server is connected to one of the Compatible input ports within the CP2000 head—see Figure 4.1. These connections are Cinema typically made at the time of projector installation.

  • Page 99: Image Formats

    Figure 4.2. Standard Cinema Formats Achieving either of these displays from a wide variety of incoming source material depends on proper settings in the projector as well as certain theatre conditions. LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 100 The screen shown in Figure 4.4 at right also has a bottom mask. • Add masks for “scope” Figure 4.4. Top Masking for Scope • Open masks for “flat” LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 101 This arrangement is the most flexible of all. Figure 4.5. Side Masking for Flat Refer to Table 4.2 for a summary of the basic factors affecting cinema displays in a variety of theatres. LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 102 CINEMA OPERATION Table 4.2. Basic Ways to Achieve Flat & Scope Displays LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)

  • Page 103: Selecting The Cinema Source

    Cinema Source Via Touch Panel Controller  As described in 3.5, Using the Touch Panel Controller, CP2000 displays are usually pre-configured so that any user can correctly display a desired feature simply by selecting the corresponding button on either page of the Main menu displayed by the Touch Panel Controller.

  • Page 104: Compatible Non-Cinema Sources

    PC or other graphics devices. Such a source routes to a DVI (Digital Visual Interface) port in the CP2000 projection head, and can bypass cinema processing when necessary. NOTE: This section assumes that “Phase 1” (or later) hardware is present in the projector, enabling use of the DVI- 2 port.
  • Page 105 NOTES: 1) Neither the Christie dual-link adapter nor the proposed 3 -party twin- link source (and cables) shown here are currently available. 2) Using both DVI ports with the Christie Cine-IPM 2K enables 10-bit output and displays. Consult the Cine- IPM 2K User’s Manual for details. LIT MAN USR CP2000...

  • Page 106: Selecting The Source

    TO SELECT A NON-CINEMA SOURCE : With a non-cinema source connected to the CP2000, use the main menu on the Touch Panel Controller to select the display C ontroller button representing the desired non-cinema source. Once selected, the button will darken and the projected display will change according to the corresponding file settings.

  • Page 108: Warnings And Guidelines

    General Precautions  Be aware of the following general precautions in all CP2000 installations: WARNING Never look directly into the projector lens or at the lamp. The extremely high brightness can cause permanent eye damage.
  • Page 109 Disconnect at BOTH wall breakers. Lamp Precautions  Any Xenon arc lamp used in the CP2000 is under high pressure and must be handled with great care at all times. Lamps may explode if dropped or mishandled. Wear Protective Clothing Never open the lamp door unless you are wearing authorized protective clothing such as that included in a Christie Protective Clothing Safety Kit #598900-095.

  • Page 110: Maintaining Proper Cooling

    Liquid Cooler  The liquid cooler system circulates liquid to and from the DMDs in the CP2000 projection head, reducing their operating temperature to an acceptable level. Periodically check the coolant level visible through the gauge/window on the non- operator’s side of the pedestal, and make sure that it remains between the two notches...

  • Page 111: Maintenance & Cleaning

    FILLING THE COOLER: The cooler should require filling only upon projector installation (see 2.1, Assembly and Connection of Components). Fill with Christie’s 50/50 mix of distilled water and ethylene glycol. Top up as necessary, watching the gauge closely. IMPORTANT: Whenever coolant has been added or replaced, check for a possible airlock upon the next projector power-up.

  • Page 112: Cleaning The Reflector

    1. Brush most of the dust off with a camel-hair brush and/or blow dust away with compressed air. 2. If some dust remains, just leave as is—air circulating at the lamp is unfiltered, so some dust is inevitable. Avoid unnecessary cleaning. LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)

  • Page 113: Replacing The Lamp & Filter

    Inspect regularly and confirm that 1) there are no obstructions or “kinks” within the ducting, 2) all air intake areas of the CP2000 are unobstructed, and 3) exhaust airflow is within the range shown in Table 2.1. Make sure lamp wiring does not interfere with vane switch.
  • Page 114 MAINTENANCE Lamp Replacement  NOTE: For this procedure you will need a compatible Christie Xenon CDXL or CXL Procedure lamp as shown in Section 8, Specifications—never install a lamp intended for a different model or projector. WARNING Make sure to use the correct wattage lamp supplied by Christie.
  • Page 115 Figure 6.1. Install Bulb 8.2. Rest the anode (+) end of the lamp on the lamp cradle as shown in Figure 6.1, right, and slip the positive lamp connector over the bulb end. LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 116 (2.0, 3.0, 4.5 or 6.0 kW) in the Touch Panel Controller’s Install menu before igniting the new lamp. This setting establishes the proper range of power available for the installed lamp, ensuring that the new lamp is neither under-powered nor over-driven. LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)

  • Page 117: Replacing A Lens

    Slide the old filter up and discard. Insert the new air filter, following the labeling for proper inside/outside orientation. Slide all the way down into its slot. WARNING Use only Christie filters. Never operate the projector without the filter installed. STEPS 5-6 ...

  • Page 118: Troubleshooting

    6. If there is no “buzzing” indicating that the igniter is attempting ignition, there may be a problem with the igniter (Christie service required). 7. If there is a brief “buzz” attempting ignition but a lamp does not ignite, the lamp likely needs to be replaced.
  • Page 119 4. If you still have trouble establishing communications with a projector added to an existing Ethernet network, the projector’s IP address is likely in conflict with another address already in use. Contact your network administrator. LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)

  • Page 120: Non-Cinema Displays

    Image appears vertically stretched or “squeezed” into center of screen CAUSE / REMEDY: ’s 1. Source data converted from film and “pre-squeezed” for CP2000 display format may require use of the anamorphic lens to regain full “scope” image width and proper proportions.
  • Page 121 1. The color, tint, color space and/or color temperature settings may require adjustment at your input source. 2. Make sure you are using the proper PCF, TCGD and/or CSC file for this source. LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 122 2. Or, if you do not have access to the Touch Panel Controller’s Advanced menu and cannot adjust the processing path, use your 3 -party input source to crop off the streaks. LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 124 NOTES: 1) Due to continuing research, specifications are subject to change without notice. Specifications Specifications apply to all models unless otherwise noted. Refer to the separate CP2000-S Addendum for Installation and Use for CP2000-S power related specifications. Display  Panel Resolution and Refresh Rate...

  • Page 125: Cinema Inputs

    230 W Max. current at this AC input Lamp DC Max. voltage 41 VDC Start-up voltage 80 V min., 107 V max. Max. current consumption 170 A Max. power consumption 6600 W LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 126 80 – 107 VDC Start-up voltage 20 – 32 VDC Operating voltage range 50 – 120 A Operating current range 5% @ 25°C Max. ripple CP2000h Pedestals INTERNAL “CONVENIENCE AC” , above LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)

  • Page 127: Audible Noise

    SPECIFICATIONS CP2000-S Pedestals (refer to separate addendum provided) Lamps  Model CXL/CDXL Lamps Current Range Lamp Life (warranty hrs.) (kW) (amps) CP2000-i/h/-S CDXL-20 (2.0) 66-88 1200 full / 2400 pro-rated CXL/CDXL-30 (3.0) 82-120 720 full / 1440 pro-rated CP2000-h/-S CXL/CDXL-45 (4.5)
  • Page 128 SPECIFICATIONS LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)

  • Page 129: Standard Components

    • Motorized Auxiliary Lens Mount — part# 108-111102-02 • 1.25x Anamorphic Lens — part# 38-809054-51 • Protective Clothing Safety Kit #598900-095 (for opening of lamp door) • DCP Librarian Setup Software (for calibration / setup by Christie installer) LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 130 Having or requiring a linear distortion, generally in the horizontal direction. Anamorphic lenses restore a ‘scope’ (CinemaScope) or ‘flat’ format film frame to the correct appearance by increasing its horizontal proportion. The CP2000 uses a 1.25x scope anamorphic lens option only.
  • Page 131  digital cinema projector NOTE: Christie’s optional automation system is not yet available. Auto Source  The ability of a projector to automatically recognize and synchronize to the horizontal and vertical scan frequencies of an input signal for proper display.
  • Page 132 Diffused Screen  A type of rear-projection screen which spreads the light striking it. Screen gain is typically less than 1 but audience viewing angles are increased. Rarely used in cinema. Digital Cinema  LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 133 GLOSSARY Professional public presentation of theatrical content by electronic means, particularly emphasizing projectors such as the CP2000 whose image source is digital data. Also known as d-cinema and (rarely) e-cinema. Digital Interpolation  Also known as digital scaling. The process of averaging pixel information when scaling (resizing) an image up or down.
  • Page 134 LampLOC   A Christie software feature where samples of output light from a projector guide the precise position of the lamp along 3 axes—vertical, horizontal and distance to lens— so that lamp performance and output is maximized. Life Safety ...
  • Page 135 (Loopthru) with a coaxial transmission line in such a manner that the line is terminated with its characteristic impedance at the last input on the line. Not applicable in CP2000. Lumen  The unit of measure for the amount of visible light emitted by a light source. Rarely used in cinema applications.
  • Page 136 The area (in pixels, for digital images) that constitutes the entire motion picture frame image. Compare: active picture. Projector-to-Screen  The distance between the projector's front feet centers and the screen. Also called Distance "Throw Distance”. LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 137 (action data), and possibly including parameters that allow the program to be tailored for a specific venue or engagement. A show script is created by the exhibitor or installer and provides automated presentations. Automation not yet available. LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 138 Switcher  A signal selector—specifically, the Marquee Signal Switcher formerly manufactured by Christie—can be connected for adding more sources to a projector. Sync  The part of the video signal that stabilizes the picture. Sync can occur in three forms: "Composite sync": the horizontal and vertical components are together on one...
  • Page 139 For this projector, this value is expressed as the maximum percentage of the image that can be projected above or below the lens center without degrading the image quality. All CP2000 lenses have the same vertical offset range. VESA ...
  • Page 140 Selects the source type and packing mode for the current input. If cinema source A or B: 0x00 = 4:2:2 unpacked, 10-bits/color (default) 0x01 = 4:2:2 packed, 12-bits/color 0x02 = 4:4:4 unpacked, 10-bits/color 0x03 = 4:4:4 packed, 12-bits/color LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 141 Gamma (GAM) (GAM!”gamma2.6”) The “filename” representing the current gamma. For example, “gamma2.6” is typically used in theatres. Gamma files (name and content) are all currently pre- defined. Also known as “look-up tables”. LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 142 Channel” checkbox is enabled, and to all channels when the checkbox is cleared. (LPI?) What is the current LiteLOC setting for this channel? (LPI?s101) What is the LiteLOC setting for Channel 101? (LP1!12345) The current LiteLOC setting is 12345 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 143 Reply indicating the OnSite MCGD is in use Ping (PNG) (PNG?) Request for projector type and current s/w version (PNG! 032 001 002) Reply indicating cinema projector present (32), and its current version of software is v1.2 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 144 Use this screen format file (stored in projector memory). (SCF?) What is the current screen format? (SCF!”1920x1080”) Current screen format filename is 1920x1080 Screen Orientation (SOR) (SOR 0) Sets the position of the projector relative to the screen 0= Front LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 145 Set/read the time and date in the projector’s real-time (TMD! 2003 08 13 14 21 00) clock. P1 = Year (yyyy) P2 = Month (01-12) P3 = Date (1-31, day of month) P4 = Hour (0-23, 24hr clock) LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 146 NOTE: The type of error and text parameters are enclosed together in quotation marks, separated by a colon and space. In the table below, the text explanation appears as -----. Table B.2. Error Messages LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 147 Card Cage Over temperature Ballast Over temperature Lamp Life Expired Lamp Failed to Strike Unexpected Lamp Failure / Off Reading Lamp Intensity Failed SSM, Communication Failure (System Supervisor Module) SSM, Upgrade Failed LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 148 (65535 01002 ERR 002 “System Warning: 8010 00051 Prism, Temperature Warning”) (65535 01002 ERR 002 “System Warning: 8020 00001 Lamp, Life Expired”) (65535 01002 ERR 002 “System Warning: 8032 00001 SSM Read Failed”) LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 149 12 = Formatter Board Type If P1 = 1 0 = Power Status (0=Off, 1=On) System Status 2 = LiteLOC (0=Off, 1=On) 3 = Lamp Expiry 4 = Lamp Hours 5 = Total Lamp Hours B-10 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 150 40 = Formatter Red (Boot) 41 = Formatter Red (Main) 42 = Formatter Red (Config) 43 = Formatter Red (Gamma) 44 = Formatter Red (Sequence) 50 = Formatter Green (Boot) 51 = Formatter Green (Main) LIT MAN USR CP2000 B-11 020-100032-04 Rev. 1 (03/14)
  • Page 151 0 = True 1 = Inverted 9 = L/R Output Reference GPO 0 = None 1-7 = GPO#1-7 10 = Dark Time 0-4500 µs 11 = Output Sync Delay 0-200 µs B-12 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)

  • Page 152: Serial Communication Cables

    Note that a serial link is adequate for DCP Librarian use, or for downloading new main software (both tasks require a qualified Christie service technician). It cannot be used for ASCII messaging (since the TPC recognizes Ethernet only), and is too slow for servers.
  • Page 154 For example, configure the pin as an output in order to drive an external IR emitter for 3D glasses, or to automatically reduce room lighting when the projector is turned on. LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 155 In the TPC’s Custom 3D Control menu, set Output GPO according to the pins wired in the GPIO cable (see Figure C.1 ). For instance, if you have wired pins #10 (+) and #29 (–) to your 3D device, set Output GPO to GPO #2. LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 156 If you need to relocate or ship the projector, repack the pedestal and the projection head with the original packing materials used for shipping. Figure D.1. Packing the Pedestal and Projection Head LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 157 Color Temperature, 8-1 Installation, 2-11 Communications. See Ethernet Anamorphic Lens Computer Using with Proj., 2-20 Description, 3-56 Connecting to AC, 2-13 Focus, 2-28 Use for Scope Images, 4-3 Contrast Ratio, 1-1, 8-1 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 158 Fold Mirror Adjustment, 2-29 Expiry Setting, 3-27 Footlamberts, 2-24 Failure to Ignite, 3-7, 3-50, 7-1 Calibration for, 3-45 Hours of Use, 3-54 Recalibrating, 3-55 Models & Specifications, 8-4 Formats, Flat & Scope, 4-2, 4-5 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 159 Non-Cinema Saves, 3-18 Connection, 2-17, 3-6, 5-1 Screen Files, 3-21 Formats, 1-1, 5-2 Security Plates, 2-18, 3-5 Switching To, 5-3 Self Test, Built-in, 3-14 Troubleshooting, 7-3 Server Menu, 3-62 Service Contacts, 1-3 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)
  • Page 160 White Tolerance in Gamut Menu, 3-38, 3-39 Advanced/Lamp History Menu, 3-28 Who Should Use This Manual, 1-4 Advanced/Lamp Menu, 3-27 Advanced/Preferences Menu, 3-26 Advanced/Test Pattern Menu, 3-29 Advanced/User Menu, 3-30 Zoom Adjustment (Primary Lens), 3-56 Alarm Window, 3-15 LIT MAN USR CP2000 020-100032-04 Rev. 1 (03/14)

Table of Contents