IBM pSeries 690 Service Manual page 457

Error Code Description
101C F596 An N+1 boundary (DCA or fan) has dropped to
N-mode status in the processor subsystem,
location: U1.18
101C F5A6 An N+1 boundary (DCA or fan) has dropped to
N-mode status in the processor subsystem,
location: U1.18
101C xx11 Processor subsystem / DCA-1
101C xx13 Seeprom (VPD) fault on processor subsystem
DCA-1
101C xx15 Processor subsystem / DCA-1 cable fault
101C xx21 Processor subsystem / DCA-2
101C xx23 Seeprom (VPD) fault on processor subsystem
DCA-2
101C xx25 Processor subsystem / DCA-2 cable fault
101C xx31 Processor subsystem / DCA-3
101C xx33 Seeprom (VPD) fault on processor subsystem
DCA -3
101C xx35 Processor subsystem / DCA-3 cable fault
101C xx41 Processor subsystem / DCA-4
101C xx43 Seeprom (VPD) fault on processor subsystem
DCA-4
101C xx45 Processor subsystem / DCA-4 cable fault
101C xx51 Processor subsystem / DCA-5
101C xx53 Seeprom (VPD) fault on processor subsystem
DCA-5
Action/
Possible Failing FRU
This is normally an informational message. It
should be accompanied by other error codes
that more precisely indicate where the failure is.
Examine the service processor error log. If there
are no other power-related error codes (in the
time frame in which this code was generated) in
the service processor error log, the FRU
indicated with this error code, if any, should be
replaced.
This is normally an informational message. It
should be accompanied by other error codes
that more precisely indicate where the failure is.
Examine the service processor error log. If there
are no other power-related error codes (in the
time frame in which this code was generated) in
the service processor error log, the FRU
indicated with this error code, if any, should be
replaced.
U1.18-P1-V1
U1.18-P1-V1
Go to "MAP 1520: Power" on page 190 with
these pairs of location codes:
1. U1.18-P1-V1/Q1 and U1.35-P1-X4/Q5
2. U1.18-P1-V1/Q2 and U1.35-P2-X4/Q5
U1.18-P1-V2
U1.18-P1-V2
Go to "MAP 1520: Power" on page 190 with
these pairs of location codes:
1. U1.18-P1-V2/Q1 and U1.35-P1-X4/Q6
2. U1.18-P1-V2/Q2 and U1.35-P2-X4/Q6
U1.18-P1-V4
U1.18-P1-V4
Go to "MAP 1520: Power" on page 190 with
these pairs of location codes:
1. U1.18-P1-V4/Q1 and U1.35-P1-X4/Q7
2. U1.18-P1-V4/Q2 and U1.35-P2-X4/Q7
U1.18-P1-V5
U1.18-P1-V5
Go to "MAP 1520: Power" on page 190 with
these pairs of location codes:
1. U1.18-P1-V5/Q1 and U1.35-P1-X3/Q9
2. U1.18-P1-V5/Q2 and U1.35-P2-X3/Q9
U1.18-P1-V6
U1.18-P1-V6
Chapter 5. Error Code to FRU Index
437