Mitsubishi Electric MELSEC iQ-F FX5 User Manual page 121

Address: decimal (hexadecimal)
CH1 CH2
1171 (493H) 1172 (494H)
1175 to 1180 (497H to 49CH)
1181 (49DH) 1182 (49EH)
1185 to 1190 (4A1H to 4A6H)
1191 (4A7H) 1192 (4A8H)
1195 to 1200 (4ABH to 4B0H)
1201 (4B1H) 1202 (4B2H)
1205 to 1210 (4B5H to 4BAH)
1211 (4BBH) 1212 (4BCH)
1215 to 1220 (4BFH to 4C4H)
1221 (4C5H) 1222 (4C6H)
1225 to 1230 (4C9H to 4CEH)
1231 (4CFH) 1232 (4D0H)
1235 to 1320 (4D3H to 528H)
1321 (529H) 1322 (52AH)
1325 to 1330 (52DH to 532H)
1331 (533H) 1332 (534H)
1335 to 1339 (537H to 53BH)
1340 (53DH) 1342 (53FH)
1341 (53DH) 1343 (53FH)
1348 to 1360 (544H to 550H)
1361 (551H) 1362 (552H)
1365 to 1370 (555H to 55AH)
1371 (55BH) 1372 (55CH)
1375 to 1380 (55FH to 564H)
1381 (565H) 1382 (566H)
1385 to 3100 (569H to C1CH)
3101 (C1DH)
3102 (C1EH)
3103 (C1FH)
3104 to 3130 (C20H to C3AH)
3131 (C3BH)
3132 to 3159 (C3CH to C57H)
3160 (C58H)
3161 to 4000 (C59H to FA0H)
4001 to 4016 (FA1H to FB0H)
4017 to 4020 (FB1H to FB4H)
4021 to 4036 (FB5H to FC4H)
CH3 CH4
1173 (495H) 1174 (496H)
1183 (49FH) 1184 (4A0H)
1193 (4A9H) 1194 (4AAH)
1203 (4B3H) 1204 (4B4H)
1213 (4BDH) 1214 (4BEH)
1223 (4C7H) 1224 (4C8H)
1233 (4D1H) 1234 (4D2H)
1323 (52BH) 1324 (52CH)
1333 (535H) 1334 (536H)
1344 (541H) 1346 (543H)
1345 (541H) 1347 (543H)
1363 (553H) 1364 (554H)
1373 (55DH) 1374 (55EH)
1383 (567H) 1384 (568H)
Name Default
value
CH Input signal error 20
detection upper limit setting
value

System area
CH Alert output setting 0001H
(Process alarm)

System area
CH Process alarm upper 0
lower limit value

System area
CH Process alarm lower 0
upper limit value

System area
CH Alert output setting 0001H
(Rate alarm)

System area
CH Rate alarm alert 0
detection cycle setting

System area
CH Rate alarm lower limit -3200
value

System area
CH A/D conversion enable/ 0
disable setting

System area
CH Digital filter conversion 0
cycle monitor
System area 
CH Digital filter fluctuation 0
width setting (L)
CH Digital filter fluctuation
width setting (H)

System area
CH Difference conversion 0000H
state flag

System area
CH Difference conversion 0
standard value

System area
CH Difference conversion 0000H
trigger

System area
Latest address of error 0
history
Latest alarm code 0
Latest address of alarm 0
history

System area
Firmware version 0
System area 
Operation mode monitor 0
System area 
Interrupt factor detection flag 0
*2
[n]
System area 
*2
Interrupt factor mask [n] 0
Appendix 4 Buffer Memory Areas
Data Auto
type refresh

Setting
 

Setting
 
Setting 
 
Setting 
 
Setting 
 
Setting 
 

Setting
 

Setting
 

Monitor
 
A

Setting
 
Monitor 
 

Monitor
 
Control 
 

Monitor

Monitor

Monitor
 

Monitor
 

Monitor
 

Monitor
 

Control
APPX
119