Siemens CU240B-2 Parameter Manual page 575

0
1
Ramp-function generator active
Mop configuration
- ... - 2
p1030 [D] (0000 0110 bin)
3
4
STW setpoint chan
r1198
r1198 .13
Mop raise
p1035 [C]
[2505.7]
(0)
STW setpoint chan
r1198
Mop lower
r1198 .14
p1036 [C]
[2505.7]
(0)
MotP n_max
-210000.000 ... 210000.000 [1/min]
p1037 [D] (0.000)
<1>
MotP n_min
-210000.000 ... 210000.000 [1/min]
p1038 [D] (0.000)
<1>
<1>
For automatic commissioning, p1037 and p1038 are set to the
maximum motor frequency or to the rated motor frequency,
provided that f_max_mot has not been specified.
<2>
If initial rounding-off is active (p1030.2 = 1), the selected ramp-up/
down times are exceeded accordingly.
<3> Only effective if p1030.0 = 0.
1 2
Setpoint channel
Motorized potentiometer
0
Data save active The setpoint for the motorized potentiometer is not saved and after ON is entered using p1040.
1 The setpoint for the motorized potentiometer is saved in a ashion after OFF and after ON set to the saved value.
0
Automatic mode Without ramp generator in automatic mode (ramp-up/ramp-down time = 0).
1
With ramp generator in automatic mode.
0
Initial rounding-off active Without initial rounding.
1 With initial rounding. The ramp-up/down time set is exceeded accordingly.
Save in NVRAM active 0 Not saved in the NVRAM (NVRAM = Non Volatile Random Access Memory).
1 Save in NVRAM active.
0
Ramp-function generator is
Ramp-up encoder inactive with pulse disable.
always active
1 The ramp-up encoder is calculated independently of the pulse enable.
0
Old value is kept
-1
1
Mop manual/auto
p1041 [C]
0 0
0 1
0
-1
1
1 0
1 1
MotP inv
p1039 [C]
(0)
Mop auto setpoint
p1042 [C]
(0)
3 4
p1030.1
&
(0)
0.000 ... 1000.000 [s]
Mop n_set bef RFG [1/min]
r1045
0 1
x
1 0
f_max (reference value for
ramp-function generator p1082)
[3050.5]
Mop set val
p1044 [C]
(0)
MotP acc set val
p1043 [C]
(0)
[2634.8] 1: OFF1 enable missing (r0046.0)
0:
5 6
FP_3020_97_51.vsd
13.12.2010
<2> <2>
Mop ramp-up time Mop ramp-down time
0.000 ... 1000.000 [s]
p1047 [D] (10.000) p1048 [D] (10.000)
y
p1082
Mop setp after
y
x
e.g. to [3030.1]
-p1082
y = 0
Mop start value
-210000.000 ... 210000.000 [1/min]
p1040 [D] (0.000)
<3>
p1030.4
0
1
7
Function diagram
G120 CU240B/E-2
V4.4
RFG [1/min]
r1050
8
- 3020 -