Atmel AT90PWM2 Manual page 300

T = -40°C to +105°C, V
A
Symbol Parameter
Power Supply Current
I
CC
Power-down mode
Analog Comparator
Input Offset Voltage
V
ACIO
AT90PWM2/3
Analog Comparator
Hysteresis Voltage
V
hysr
AT90PWM2B/3B
Analog Comparator
I
ACLK
Input Leakage Current
Analog Comparator
t
ACID
Propagation Delay
Note: 1. "Max" means the highest value where the pin is guaranteed to be read as low
2. "Min" means the lowest value where the pin is guaranteed to be read as high
3. Although each I/O port can sink more than the test conditions (20 mA at V
conditions (non-transient), the following must be observed:
SO32, SO24 and TQFN Package:
1] The sum of all IOL, for all ports, should not exceed 400 mA.
2] The sum of all IOL, for ports B6 - B7, C0 - C1, D0 - D3, E0 should not exceed 100 mA.
3] The sum of all IOL, for ports B0 - B1, C2 - C3, D4, E1 - E2 should not exceed 100 mA.
4] The sum of all IOL, for ports B3 - B5, C6 - C7 should not exceed 100 mA.
5] The sum of all IOL, for ports B2, C4 - C5, D5 - D7 should not exceed 100 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
4. Although each I/O port can source more than the test conditions (20 mA at Vcc = 5V, 10 mA at Vcc = 3V) under steady state
conditions (non-transient), the following must be observed:
SO32, SO24 and TQFN Package:
1] The sum of all IOH, for all ports, should not exceed 400 mA.
2] The sum of all IOH, for ports B6 - B7, C0 - C1, D0 - D3, E0 should not exceed 150 mA.
3] The sum of all IOH, for ports B0 - B1, C2 - C3, D4, E1 - E2 should not exceed 150 mA.
4] The sum of all IOH, for ports B3 - B5, C6 - C7 should not exceed 150 mA.
5] The sum of all IOH, for ports B2, C4 - C5, D5 - D7 should not exceed 150 mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
4317I–AVR–01/08
= 2.7V to 5.5V (unless otherwise noted) (Continued)
CC
Condition
Active 8 MHz, V
RC osc, PRR = 0xFF
Active 16 MHz, V
Ext Clock, PRR = 0xFF
Idle 8 MHz, V
Osc
Idle 16 MHz, V
Ext Clock
WDT enabled, V
t0 < 90°C
WDT enabled, V
t0 < 105°C
(5)
WDT disabled, V
t0 < 90°C
WDT disabled, V
t0 < 105°C
V = 5V, V
CC
V = 5V, V
CC
Rising Edge
Falling Edge
V = 5V
CC
V = V /2
in CC
V = 2.7V
CC
V = 5.0V
CC
Min.
= 3V,
CC
= 5V,
CC
= 3V, RC
CC
= 5V,
CC
= 3V
CC
= 3V
CC
= 3V
CC
= 3V
CC
= 3V
in
= 3V
in
33
34
-50
AT90PWM2/3/2B/3B
Typ. Max.
3.8 7
14 24
1.5 3
5.5 10
5 15
9 20
2 3
5 10
20 50
46 71
62 110
50
(6)
(6)
= 5V, 10 mA at V = 3V) under steady state
CC CC
Units
mA
mA
mA
mA
µA
µA
µA
µA
mV
mV
mV
nA
ns
301