WEG CFW501 V1.8X Programming Manual page 20

Quick Reference of Parameters, Alarms and Faults
0
Param. Function
P0513 Indirect Indication Form 2
P0516 Ref. Eng. Unit 4
P0517 Indirect Indication Form 4
P0580 Fire Mode Configuration
P0581 Setpoint PID fire Mode
P0582 Auto-reset configuration
P0583 Bypass Mode Configuration
P0584 Bypass Contactor time
P0585 Short Cycle Protection Config.
P0586 Minimum RUN Time
P0587 Minimum STOP Time
P0588 Energy Saving Max. Torque
P0589 Energy Saving Min. Mag.
P0590 Energy Saving Min. Speed
P0591 Energy Saving Hysteresis
P0680 Logical Status
P0681 Speed in 13 bits
P0682 Serial/USB Control
P0683 Serial/USB Speed Ref.
0-12 | CFW501
Adjustable Range
0 = wxyz
1 = wxy.z
2 = wx.yz
3 = w.xyz
See options in P0510
0 = wxyz
1 = wxy.z
2 = wx.yz
3 = w.xyz
0 = Inactive
1 = Active
2 = Active / P0134
3 = Active / P0581
4 = Active / Gen. Disable
-32768 to 32767
0 = Limited
1 = Unlimited
0 = Inactive
1 = Active/DIx
2 = Active/DIx+Failure
0.00 to 300.00 s
0 = Inactive
1 = Active
0 to 650.00 s
0.00 to 650.00 s
0 to 85 %
40 to 80 %
360 to 18000 rpm
0 to 30 %
Bit 0 = Not Used
Bit 1 = Run Command
Bit 2 = Fire mode
Bit 3 = Bypass
Bit 4 = Quick Stop
Bit 5 = 2 Ramp
nd
Bit 6 = Config. Mode
Bit 7 = Alarm
Bit 8 = Running
Bit 9 = Enabled
Bit 10 = Forward
Bit 11 = JOG
Bit 12 = Remote
Bit 13 = Subvoltage
Bit 14 = Reserved
Bit 15 = Fault
-32768 to 32767
Bit 0 = Ramp Enable
Bit 1 = General Enable
Bit 2 = Run Forward
Bit 3 = JOG Enable
Bit 4 = Remote
Bit 5 = 2 Ramp
nd
Bit 6 = Quick Stop
Bit 7 = Fault Reset
Bit 8....12 = Not Used
Bit 13 = Intern PID
Bit 14 = Extern PID
Bit 15 = Reserved
-32768 to 32767
User
Factory Setting Propr.
Setting
1
13
1
0 cfg
0
0 cfg
0 cfg
0.30 s cfg
0 cfg
5.00 s cfg
5.00 s cfg
60 % cfg, V/f
40 % cfg, V/f
600 (525) rpm cfg, V/f
10 % cfg, V/f
Groups Pag.
HMI 5-9
HMI 5-9
HMI 5-10
HVAC 18-30
HVAC 18-30
HVAC 18-31
HVAC 18-34
HVAC 18-34
HVAC 18-3
HVAC 18-4
HVAC 18-4
HVAC 18-2
HVAC 18-2
HVAC 18-3
HVAC 18-3
ro READ, 16-2
NET
ro NET 16-2
ro NET 7-12
16-2
ro NET 16-2