Mitsubishi Electric FR-A820-00046 Instruction Manual page 254

Parameter List
(G) Control Parameter
Parameters for motor control.
Pr.
Pr. Name
group
G000 0
Torque boost
G001 3
Base frequency
G002 19 Base frequency voltage
G003 14 Load pattern selection
G010 46 Second torque boost
G011 47 Second V/F (base frequency)
G020 112 Third torque boost
G021 113 Third V/F (base frequency)
G030 60 Energy saving control selection
G040 100 V/F1(first frequency)
G041 101 V/F1(first frequency voltage)
G042 102 V/F2 (second frequency)
G043 103 V/F2 (second frequency voltage)
G044 104 V/F3 (third frequency)
G045 105 V/F3 (third frequency voltage)
G046 106 V/F4 (fourth frequency)
G047 107 V/F4 (fourth frequency voltage)
G048 108 V/F5 (fifth frequency)
G049 109 V/F5 (fifth frequency voltage)
SF-PR slip amount adjustment
G060 673
operation selection
G061 674 SF-PR slip amount adjustment gain
Reverse rotation excitation current
G080 617
low-speed scaling factor
DC injection brake operation
G100 10
frequency
G101 11 DC injection brake operation time
G102 802 Pre-excitation selection
G103 850 Brake operation selection
G105 522 Output stop frequency
G106 250 Stop selection
G107 Special regenerative brake duty
70
G108 1299 Second pre-excitation selection
DC injection brake operation
G110 12
voltage
Regeneration avoidance operation
G120 882
selection
Regeneration avoidance operation
G121 883
level
Regeneration avoidance at
G122 884
deceleration detection sensitivity
Regeneration avoidance
G123 885
compensation frequency limit value
Regeneration avoidance voltage
G124 886
gain
Regeneration avoidance frequency
G125 665
gain
Increased magnetic excitation
G130 660
deceleration operation selection
Tab. 5-16: Control Parameter (1)
5 - 52
Refer to
page
5-688
Simple Simple Simple
5-690
Simple Simple Simple
5-690
5-692
5-688
5-690
5-688
5-690
5-697
5-698
5-698
5-698
5-698
5-698
5-698
5-698
5-698
5-698
5-698
5-700
5-700
5-692
5-701
5-701
5-701
5-701
5-709
5-447
5-713
5-701
5-701
5-723
5-723
5-723
5-723
5-723
5-723
5-727
Pr.
Pr. Name
group
G131 661 Magnetic excitation increase rate
Increased magnetic excitation
G132 662
current level
G200 800 Control method selection
G201 85 Excitation current break point
Excitation current low speed scaling
G202 86
factor
G203 245 Rated slip
G204 246 Slip compensation time constant
Constant-power range slip
G205 247
compensation selection
Constant output range speed
G206 1116
control P gain compensation
Constant output range torque
G210 803
characteristic selection
G211 820 Speed control P gain 1
G212 821 Speed control integral time 1
Torque control P gain 1 (current loop
G213 824
proportional gain)
Torque control integral time 1
G214 825
(current loop integral time)
G215 Speed detection filter 1
823
G216 827 Torque detection filter 1
G217 854 Excitation ratio
Speed control integral term clear
G218 1115
time
Speed feed forward control/model
G220 877
adaptive speed control selection
G221 878 Speed feed forward filter
G222 879 Speed feed forward torque limit
G223 881 Speed feed forward gain
G224 828 Model speed control gain
G230 840 Torque bias selection
G231 841 Torque bias 1
G232 842 Torque bias 2
G233 843 Torque bias 3
G234 844 Torque bias filter
G235 845 Torque bias operation time
G236 846 Torque bias balance compensation
G237 847 Fall-time torque bias terminal 1 bias
G238 848 Fall-time torque bias terminal 1 gain
G240 Speed feedback range
367
G241 Feedback gain
368
Tab. 5-16: Control Parameter (2)
Parameters
Refer to
page
5-727
5-727
5-61
5-692
5-692
5-729
5-729
5-729
5-103
5-90,
5-138
5-103
5-103
5-150,
5-196
5-150,
5-196
5-194
5-194
5-195
5-103
5-115
5-189
5-115
5-115
5-115
5-115,
5-189
5-119
5-119
5-119
5-119
5-119
5-119
5-119
5-119
5-119
5-730
5-730