Icom ID-31A PLUS Advanced Manual page 170

11
MENU SCREEN
DV Set items
Fast Data
MENU > DV Set > DV Fast Data > Fast Data
Turn the DV Fast Data function ON or OFF for data
communication in the DV mode�
The DV Fast Data function uses data and the audio
frames to send data approximately 3�5 times faster
than the normal speed� No audio can be sent�
L While holding down [PTT], the data is sent at the
slow speed, even if "ON" is selected� This is because
the audio frame is used for the microphone audio
transmission and the audio transmission has priority� The
GPS data speed is set in GPS Data Speed�
L When you send data to other transceivers that can
receive only slow speed data, set to "OFF�"
• OFF: Sends data at the slow speed (approximately
950 bps)�
• ON: Sends data at the fast speed (approximately
3480 bps)�
GPS Data Speed
MENU > DV Set > DV Fast Data > GPS Data Speed
Set the GPS data speed when the data is sent using
the DV Fast Data function�
L When you send GPS data to other transceivers that can
receive only slow speed data, set to "Slow�"
• Slow: Sends GPS data in the slow speed
(approximately 950 bps)�
• Fast: Sends GPS data in the fast speed
(approximately 3480 bps)�
TX Delay (PTT)
MENU > DV Set > DV Fast Data > TX Delay (PTT)
Set the TX delay time�
In the data communication mode and after releasing
[PTT], the transceiver automatically sends the data
using the DV Fast Data function for this set period of
time�
NOTE: This function is usable only when DV Data
TX is set to "PTT�"
• OFF: After releasing [PTT], the transceiver
returns to receive�
• 1 ~ 10sec: After releasing [PTT], the transceiver
sends data by using the DV Fast Data
function for this set period of time�
The transceiver automatically returns to
receive when the TX data is completely
sent, or when this period of time ends,
whichever is sooner�
(Default: OFF) Digital Monitor
MENU > DV Set > Digital Monitor
Select a Receive mode when you push [SQL] in the
DV mode�
• Auto:
• Digital: Receives in the DV mode�
• Analog: Receives in the FM mode�
Digital Repeater Set
MENU > DV Set > Digital Repeater Set
Turn the Digital Repeater Setting function ON or OFF�
In any DV mode except when using the DR function,
and when accessing a repeater that has a call sign
different from the transceiver's setting, this function
reads the repeater's signal and automatically sets the
repeater call sign in R1 and R2�
• OFF: Turns OFF the function�
• ON:
(Default: Slow)
RX Call Sign Write
MENU > DV Set > RX Call Sign Write
Set the RX Call Sign Automatic Write function to Auto
or OFF� When receiving a call addressed to your own
call sign in any DV mode except when using the DR
function, this function automatically sets the caller
station call sign into "UR�"
• OFF: Turns OFF the function.
• Auto: Automatically sets the call sign of the caller
(Default: 2sec)
RX Repeater Write
MENU > DV Set > RX Repeater Write
Set the Repeater Call Sign Automatic Write function
to Auto or OFF� When receiving a call addressed to
your own call sign through a repeater in any DV mode
except when using the DR function, this function
automatically sets the call sign of the repeater into
"R1" or "R2�"
• OFF: Turns OFF the function.
• Auto: Automatically sets the call sign of the repeater
DV Auto Detect
MENU > DV Set > DV Auto Detect
Turn the DV Mode Automatic Detect function ON or
OFF� If you receive an FM signal in the DV mode, this
function temporarily switches to the FM mode�
• OFF: Turns OFF the function� The operating mode
• ON:
11-27
Receives in the DV mode or the FM mode,
depending on the received signal�
Automatically sets the repeater call sign�
station into "UR�"
into "R1" or "R2�"
is fixed to the DV mode.
Automatically selects the FM mode for
temporal operation�
(Default: Auto)
(Default: ON)
(Default: OFF)
(Default: OFF)
(Default: OFF)