GE B30 Communications Manual page 455

CHAPTER 3: IEC 61850 COMMUNICATION
Data object CDC Semantics
name
LocSetAcsOff SPS Indicates operations of FlexLogic operand ACCESS LOC SETG OFF
LocSetAcsOn SPS Indicates operations of FlexLogic operand ACCESS LOC SETG ON
LosLife MV XFMR LIFE LOST actual values
LosLifeRte MV DAILY RATE LOL actual values
LosPkt1 SPS The lost packet threshold has been exceeded.
The 87L DIFF CH 1 LOSTPKT operand, which becomes On when the differential
element has detected the lost packet threshold has been exceeded on channel 1.
LossLd ACT The high impedance fault phase A, B, C loss of load element has operated
Lower SPS PID Lower operand. The PID 1 LOWER operand value.
MAC VSG Expected value of Destination MAC address field in messages subscribed to by
RxGOOSE#
MajorErr SPS Any of the major self-test errors generated (major error).
The ANY MAJOR ERROR operand.
ManMod SPS Capacitor control in manual mode.
The CAP 1 IN MAN operand.
MaxAsymOp1 SPS Asymmetry on the channel exceeded pre-set value.
The 87L DIFF CH 1 MAX ASYM operand, which becomes On when the Asymmetry
on channel 1 exceeded preset value.
MaxCompHz MV The frequency of the learned maximum broken rotor bar spectral component.
MAXIMUM COMPONENT FREQ. in Hz.
MaxCompLevel MV Indicates the learned maximum level of the broken rotor bar spectral component
since the last data clear.
MAXIMUM COMPONENT LEVEL in dB.
MaxIntrA MV Indicates Breaker Arcing Current per phase.
BKR 1 AMP MAX phase A/B/C.
MaxLoadDev MV Indicates the motor load standard deviation at the time when data for the
maximum broken rotor bar was acquired.
LOAD DEV. AT BRB MAX in x FLA.
MaxMotLoad MV Indicates the average motor load at the time when data for the maximum broken
rotor bar was acquired.
MOTOR LOAD AT BRB MAX in x FLA.
MaxVal1 ASG Maximum value in deadband calculations
MinorErr SPS Any of the minor self-test errors generated (minor error).
The ANY MINOR ERROR operand.
MinVal1 ASG Minimum value in deadband calculations
MMSConnects MV Number of MMS client connections active
MnlCls SPS Manual close initiated.
The BREAKER 1 MNL CLS operand.
MnlOpn SPS Manual open initiated.
The BREAKER 1 MNL OPEN operand.
Month1 SPS Current month, where 1 = January.
The MONTH operand.
MotLoad MV The average motor load at the time of the broken rotor bar data acquisition stage.
MOTOR LOAD AT BRB CALC. in x FLA
MotStatus ENS Indicated the status of the motor (in Actual Values) where 0 = Offline, 1= Starting,
2 = Running and 3 = Overload.
Thermal Model MOTOR STATUS.
MotUnb MV % thermal model motor unbalance.
THERMAL MODEL MOTOR UNBALANCE in percentage (%).
NegTotVArh MV SRC 1 Total VAr-hour in negative direction
NegTotWh MV SRC 1 Total Watt-hour in negative direction
NeutOpn SPS Indicates source has lost voltage signal.
The SRC1 VT NEU WIRE OPEN operand.
UR FAMILY – COMMUNICATIONS GUIDE
MODEL IMPLEMENTATION CONFORMANCE STATEMENT (MICS)
Used in logical nodes...
SecGSAL
SecGSAL
LosLifSPTR
LosLifSPTR
LinDfPDIF
HiZPHIZ
PIDRegFPID
LGOS
LPHD
CapCtlGAPC
LinDfPDIF
BknRotSVBR
BknRotSVBR
CBArcΘSCBR
BknRotSVBR
BknRotSVBR
TDCInGGIO1,
TDCOutGGIO1
LPHD
TDCInGGIO1,
TDCOutGGIO1
LPHD
Bkr0XCBR
Bkr0XCBR
TmDayGAPC
BknRotSVBR
MotThmPTTR
MotThmPTTR
EnrMtrMMTR
EnrMtrMMTR
VtffGAPC
3-217
3