GE B30 Communications Manual page 452

MODEL IMPLEMENTATION CONFORMANCE STATEMENT (MICS)
Data object CDC
name
DynArmd SPS
DynDpo SPS
DynOp SPS
Ena1 SPS
EqLim SPS
3
EqpMismat SPS
EvtEna1 ENG
EvtLED SPS
EvtRcdClr SPC
Fail SPS
FDLOp SPS
FlexErrTkn SPS
Flt3Ph SPS
FltAB SPS
FltABG SPS
FltAG SPS
FltBC SPS
FltBCG SPS
FltBG SPS
FltCA SPS
FltCAG SPS
FltCG SPS
FltCntClr SPC
FltCntPhφ INS
FltLinID VSS
FltLocation MV
FltLoopReact MV
3-214
Semantics
This data object indicates that dynamic mode is armed.
The SYNC1 S-CLOSE ARMD operand, which becomes On when dynamic mode is
armed.
The SYNC1 S-CLOSE DPO operand, which becomes Off when all criteria for
dynamic mode are fulfilled
This data object indicates that all criteria for dynamic mode are fulfilled if value is
TRUE else false.
The SYNC1 S-CLOSE OP operand, which becomes On when all criteria for dynamic
mode are fulfilled.
Function is Enabled.
The AR ENABLED operand.
The number of pulses counted is equal to the set number.
Counter 1(CNT1) EQL operand, which indicates the number of pulses counted is
equal to the set number.
The configuration of modules does not match the stored order code.
The EQUIPMENT MISMATCH operand.
Setting to enable generation of events in event record, 0 = Disabled, 1 = Enabled
An LED - Event Cause LED status. For graphical front panel.
The EVENT CAUSE LED 1 operand.
Clear Event Records (erase all Events).
The CLEAR EVENT RECORDS command.
Ground Protection Module Failure.
GPM-F (Field Ground Protection Module) Fail status.
The GPM-F FAILURE operand.
Overcurrent fault detector low has operated.
The 87PC FDL OP operand.
A FlexLogic equation is incorrect.
The FLEXLOGIC ERR TOKEN operand.
Fault indication - Three phase fault.
The PHASE SELECT 3P operand.
Fault indication - Phase A to B.
The PHASE SELECT AB operand.
Fault indication - Phase A to B to ground.
The PHASE SELECT ABG operand.
Fault indication - Phase A to ground.
The PHASE SELECT AG operand.
Fault indication - Phase B to C.
The PHASE SELECT BC operand.
Fault indication - Phase B to C to ground.
The PHASE SELECT BCG operand.
Fault indication - Phase B to ground.
The PHASE SELECT BG operand.
Fault indication - Phase C to A.
The PHASE SELECT CA operand.
Fault indication - Phase C to A to ground.
The PHASE SELECT CAG operand.
Fault indication - Phase C to ground.
The PHASE SELECT CG operand.
TRUE = clear incipient fault count. The clear incipient fault counters command.
Number of detected incipient faults.
INCIPIENT FAULT 1 PH A/B/C FAULTS.
Faulted line ID
Fault location in percentage.
The FAULT LOCATION in percentage of field winding from negative terminal in
case of single point injection. If double point injection, displays Invalid value.
D30, D60, L60, L90 - The fault loop reactance
CHAPTER 3: IEC 61850 COMMUNICATION
Used in logical nodes...
SynChkRSYN
SynChkRSYN
SynChkRSYN
Rec13pRREC, Rec3pRREC
DigCntFCNT
LPHD
GGIO3
LEDsIHMI
Master/LLN0
FldGnd0PHIZ
PhCmp1PDIF
LPHD
PhSelGAPC
PhSelGAPC
PhSelGAPC
PhSelGAPC
PhSelGAPC
PhSelGAPC
PhSelGAPC
PhSelGAPC
PhSelGAPC
PhSelGAPC
ICFltPTEF
ICFltPTEF
FltRFLO
FldGnd0PHIZ
FltRFLO
UR FAMILY – COMMUNICATIONS GUIDE