Siemens SINAMICS G120 Operating Instructions Manual page 465

Touch protection
Compliance with standards
Standards
CE marking
Radio interference suppres‐
sion
Approval
Ambient conditions
Ambient temperature
Relative humidity
(no condensation)
Corresponds to class
Environmental class / harm‐
ful chemical substances
Organic/biological influences 1B1 according to
Pollution degree
Installation altitude
Mechanical strength
Vibrational load
- Displacement
- Acceleration
Shock load
- Displacement
- Acceleration
Deviations from the defined classes are shown in
maximum sound pressure level, ascertained in the IP20 cabinet
1)
Standard construction: Devices installed in the control cabinet with installation in conformance with EMC regulations, line
2)
reactor uk = 2%, shielded motor cable (e.g. Protoflex EMC) with max. 100 m cable length,
line harmonics according to EN 61000‑2‑4: Class 2, THD(U) total = 8% for typical line conditions (RSC > 30 ... 50); THD(I)
total: typically 30 ... 45 % (15 < RSC < 50)
in transport packaging
3)
Converter with the CU230P-2 Control Units
Operating Instructions, 09/2017, FW V4.7 SP9, A5E34257946B AE
according to EN 61800-5-1: For the intended purpose
EN 60146-1-1, EN 61800-2, EN 61800-3, EN 61800-5-1, EN 60204-1, EN 60529
UL61800-5-1, CSA 22.2 No. 274-13
In accordance with EMC Directive No. 2014/30/EU and Low-Voltage Directive No. 2014/35/
EU
In accordance with the EMC product standard for variable-speed drives EN 61800-3, "second
environment" .
2)
Application in "first environment" possible with line filters.
cULus (File No.: E192450), CE, RCM, EAC, KC
During storage
3)
-25° ... +55° C
5 to 95%
1K4 according to EN
60721-3-1
1C2 according to
EN 60721-3-1
EN 60721-3-1
2 according to EN 61800-5-1
up to 1000 m above sea level without derating,
> 1000 m above sea level with derating (see Chapter Restrictions for special ambient condi‐
tions (Page 510))
During storage
3)
Fc test according to EN
60068-2-6
±1.5 mm for 5 ... 9 Hz
0.5 g at 9 ... 200 Hz
Fc test according to EN
60068-2-6
±1.5 mm for 5 ... 9 Hz
0.5 g for 9 ... 200 Hz
italics .
10.5 Technical data, PM330 Power Module
During transport
3)
-25 ... +70 °C
–40 °C for 24 hours
from
5 ... 95% at 40° C
2K3 according to
EN 60721-3-2
2C2 according to
EN 60721-3-2
2B1 according to
EN 60721-3-2
During transport
3)
Fc test according to EN
60068-2-6
±1.5 mm for 5 ... 9 Hz
0.5 g at 9 ... 200 Hz
Fc test according to EN
60068-2-6
±1.5 mm for 5 ... 9 Hz
0.5 g for 9 ... 200 Hz
Technical data
During operation
0° ... +40° C
up to + 50° C with derating
5 ... 95%
3K3 according to
EN 60721-3-3
3C2 according to
EN 60721-3-3
3B1 according to
EN 60721-3-3
During operation
Fc test according to EN
60068-2-6
0.075 mm for 10 ... 58 Hz
9.81 ma/s² (1 x g) at > 58 ...
200 Hz
Test according to EN
60068-2-27 (EA shock type)
49 ma/s² (5 x g)/30 ms
147 m/s² (15 x g)/11 ms
465