Table of Contents
Advertisement
S9700 Core Routing Switch
Configuration Guide - SPU
[SPU-B-Eth-Trunk0.2] arp broadcast enable
[SPU-B-Eth-Trunk0.2] quit
[SPU-B] interface eth-trunk0.1
[SPU-B-Eth-Trunk0.1] control-vid 10 dot1q-termination
[SPU-B-Eth-Trunk0.1] dot1q termination vid 10
[SPU-B-Eth-Trunk0.1] dot1q vrrp vid 10
[SPU-B-Eth-Trunk0.1] ip address 10.0.0.3 24
[SPU-B-Eth-Trunk0.1] vrrp vrid 10 virtual-ip 10.0.0.1
[SPU-B-Eth-Trunk0.1] vrrp vrid 10 track admin-vrrp interface eth-trunk0.2 vrid 11
unflowdown
[SPU-B-Eth-Trunk0.1] vrrp vrid 10 priority 110
[SPU-B-Eth-Trunk0.1] vrrp vrid 10 preempt-mode timer delay 3
[SPU-B-Eth-Trunk0.1] arp broadcast enable
[SPU-B-Eth-Trunk0.1] quit
[SPU-B] interface eth-trunk0.3
[SPU-B-Eth-Trunk0.3] control-vid 13 dot1q-termination
[SPU-B-Eth-Trunk0.3] dot1q termination vid 13
[SPU-B-Eth-Trunk0.3] ip address 13.0.0.3 24
[SPU-B-Eth-Trunk0.3] arp broadcast enable
[SPU-B-Eth-Trunk0.3] quit
Step 7 Configure the channel between SPU A and SPU B.
# Log in to SPU A to set the source IP address to 13.0.0.2, the destination IP address to 13.0.0.3,
the source port number to 3001, and the destination port number to 4001 for the channel through
which dual-system HSB data is synchronized.
[SPU] hot-standby-group local 13.0.0.2 peer 13.0.0.3 src-data-port 3001 dst-data-
port 4001
[SPU] hot-standby enable
[SPU] hot-standby-group detect fail-count 20 interval 1
# Log in to SPU B to set the source IP address to 13.0.0.3, the destination IP address to 13.0.0.2,
the source port number to 4001, and the destination port number to 3001 for the channel through
which dual-system HSB data is synchronized.
[SPU] hot-standby-group local 13.0.0.3 peer 13.0.0.2 src-data-port 4001 dst-data-
port 3001
[SPU] hot-standby enable
[SPU] hot-standby-group detect fail-count 20 interval 1
Step 8 Verify the configuration.
# Log in to SPU A to check whether VRRP negotiation is correct and whether the channel
between SPU A and SPU B is set up successfully.
[SPU-A] display vrrp
Eth-Trunk0.1|Virtual Router 10
State
Virtual IP
PriorityRun
PriorityConfig
MasterPriority
Preempt
Delay Time
TimerRun
TimerConfig
Auth Type
Virtual Mac
Check TTL
Config type
Issue 01 (2012-03-15)
NOTE
l If the value of State of SPU A is Master and the value of State of SPU B is Backup, it indicates that
VRRP negotiation is correct.
l If the value of TCP State of the SPUs is CONNECT, it indicates that the channel between SPU A and
SPU B is set up successfully.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
7 Dual-System HSB Configuration
: Master
: 10.0.0.1
: 120
: 120
: 120
: YES
: 3
: 1
: 1
: NONE
: 0000-5e00-0164
: YES
: member-vrrp
320
Advertisement
Table of Contents
