Huawei S9700 Series Configuration Manual page 261

S9700 Core Routing Switch
Configuration Guide - SPU
Data Preparation
To complete the configuration, you need the following data:
l
l
l
l
l
l
l
l
Procedure
Step 1 Configure traffic importing on the Switch.
1.
2.
Issue 01 (2012-03-15)
Network segment and index of the NAT address pool
Server names, connection quantity limits, connection rate limits, and bandwidth rate limits
Name and related parameters of the probe
Server group name, load balancing algorithm, and forwarding mode
Name and matching rule of the Layer 7 classifier
Load balancing action profile name, action, and master and backup server groups
Name of the Layer 3 classifier and ACL and Layer 7 classifier bound to the Layer 3 classifier
Name of the load balancing policy and interface where the load balancing policy is applied
Import traffic to the SPU on the Switch.
<Switch> system-view
[Switch] vlan batch 12 to 16
[Switch] interface gigabitethernet 3/0/0
[Switch-GigabitEthernet3/0/0] port link-type trunk
[Switch-GigabitEthernet3/0/0] port trunk allow-pass vlan 12
[Switch-GigabitEthernet3/0/0] undo port trunk allow-pass vlan 1
[Switch-GigabitEthernet3/0/0] quit
[Switch] interface gigabitethernet 3/0/1
[Switch-GigabitEthernet3/0/1] port link-type access
[Switch-GigabitEthernet3/0/1] port default vlan 13
[Switch-GigabitEthernet3/0/1] quit
[Switch] interface gigabitethernet 3/0/2
[Switch-GigabitEthernet3/0/2] port link-type access
[Switch-GigabitEthernet3/0/2] port default vlan 14
[Switch-GigabitEthernet3/0/2] quit
[Switch] interface gigabitethernet 3/0/3
[Switch-GigabitEthernet3/0/3] port link-type access
[Switch-GigabitEthernet3/0/3] port default vlan 15
[Switch-GigabitEthernet3/0/3] quit
[Switch] interface gigabitethernet 3/0/4
[Switch-GigabitEthernet3/0/4] port link-type access
[Switch-GigabitEthernet3/0/4] port default vlan 16
[Switch-GigabitEthernet3/0/4] quit
[Switch] interface eth-trunk 0
[Switch-Eth-Trunk0] port link-type trunk
[Switch-Eth-Trunk0] port trunk allow-pass vlan 12 to 16
[Switch-Eth-Trunk0] undo port trunk allow-pass vlan 1
[Switch-Eth-Trunk0] quit
[Switch] interface xgigabitethernet5/0/0
[Switch-XGigabitEthernet5/0/0] eth-trunk 0
[Switch-XGigabitEthernet5/0/0] quit
[Switch] interface xgigabitethernet5/0/1
[Switch-XGigabitEthernet5/0/1] eth-trunk 0
[Switch-XGigabitEthernet5/0/1] quit
Add an interface to a VLAN on the Switch, and configure an NAT address pool.
<Quidway> system-view
[Quidway] sysname SPU
[SPU] nat address-group 2 100.100.100.2 100.100.100.200
[SPU] interface eth-trunk 0
[SPU-Eth-Trunk0] quit
[SPU] interface xgigabitethernet 0/0/1
[SPU-XGigabitEthernet0/0/1] eth-trunk 0
[SPU-XGigabitEthernet0/0/1] quit
[SPU] interface xgigabitethernet 0/0/2
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
6 Load Balancing Configuration
250