Table of Contents
Advertisement
S9700 Core Routing Switch
Configuration Guide - SPU
[SPU-XGigabitEthernet0/0/1] eth-trunk 0
[SPU-XGigabitEthernet0/0/1] quit
[SPU] interface xgigabitethernet 0/0/2
[SPU-XGigabitEthernet0/0/2] eth-trunk 0
[SPU-XGigabitEthernet0/0/2] quit
Step 6 Configure VRRP.
# Log in to SPU A.
l Set the IP address of Eth-Trunk 0.2 to 11.0.0.2/24, add Eth-Trunk 0.2 to VRRP backup group
l Set the IP address of Eth-Trunk 0.1 to 10.0.0.2/24, add Eth-Trunk 0.1 to VRRP backup group
l Set the IP address of Eth-Trunk 0.3 to 13.0.0.2/24 and set parameters of Eth-Trunk 0.3.
[SPU-A] interface eth-trunk0.2
[SPU-A-Eth-Trunk0.2] control-vid 11 dot1q-termination
[SPU-A-Eth-Trunk0.2] dot1q termination vid 11
[SPU-A-Eth-Trunk0.2] dot1q vrrp vid 11
[SPU-A-Eth-Trunk0.2] ip address 11.0.0.2 24
[SPU-A-Eth-Trunk0.2] vrrp vrid 11 virtual-ip 11.0.0.1
[SPU-A-Eth-Trunk0.2] admin-vrrp vrid 11
[SPU-A-Eth-Trunk0.2] vrrp vrid 11 priority 120
[SPU-A-Eth-Trunk0.2] arp broadcast enable
[SPU-A-Eth-Trunk0.2] quit
[SPU-A] interface eth-trunk0.1
[SPU-A-Eth-Trunk0.1] control-vid 10 dot1q-termination
[SPU-A-Eth-Trunk0.1] dot1q termination vid 10
[SPU-A-Eth-Trunk0.1] dot1q vrrp vid 10
[SPU-A-Eth-Trunk0.1] ip address 10.0.0.2 24
[SPU-A-Eth-Trunk0.1] vrrp vrid 10 virtual-ip 10.0.0.1
[SPU-A-Eth-Trunk0.1] vrrp vrid 10 track admin-vrrp interface eth-trunk0.2 vrid 11
unflowdown
[SPU-A-Eth-Trunk0.1] vrrp vrid 10 priority 120
[SPU-A-Eth-Trunk0.1] vrrp vrid 10 preempt-mode timer delay 3
[SPU-A-Eth-Trunk0.1] arp broadcast enable
[SPU-A-Eth-Trunk0.1] quit
[SPU-A] interface eth-trunk0.3
[SPU-A-Eth-Trunk0.3] control-vid 13 dot1q-termination
[SPU-A-Eth-Trunk0.3] dot1q termination vid 13
[SPU-A-Eth-Trunk0.3] ip address 13.0.0.2 24
[SPU-A-Eth-Trunk0.3] arp broadcast enable
[SPU-A-Eth-Trunk0.3] quit
# Log in to SPU B.
l Set the IP address of Eth-Trunk 0.2 to 11.0.0.3/24, add Eth-Trunk 0.2 to VRRP backup group
l Set the IP address of Eth-Trunk 0.1 to 10.0.0.3/24, add Eth-Trunk 0.1 to VRRP backup group
l Set the IP address of Eth-Trunk 0.3 to 13.0.0.3/24 and set parameters of Eth-Trunk 0.3.
[SPU-B] interface eth-trunk0.2
[SPU-B-Eth-Trunk0.2] control-vid 11 dot1q-termination
[SPU-B-Eth-Trunk0.2] dot1q termination vid 11
[SPU-B-Eth-Trunk0.2] dot1q vrrp vid 11
[SPU-B-Eth-Trunk0.2] ip address 11.0.0.3 24
[SPU-B-Eth-Trunk0.2] vrrp vrid 11 virtual-ip 11.0.0.1
[SPU-B-Eth-Trunk0.2] admin-vrrp vrid 11
[SPU-B-Eth-Trunk0.2] vrrp vrid 11 priority 110
Issue 01 (2012-03-15)
11, set the virtual IP address of VRRP backup group 11 to 11.0.0.1/24, and set the priority
of VRRP backup group 11 to 120.
10, set the virtual IP address of VRRP backup group 10 to 10.0.0.1/24, and set the priority
of VRRP backup group 10 to 120.
11, set the virtual IP address of VRRP backup group 11 to 11.0.0.1/24, and set the priority
of VRRP backup group 11 to 110.
10, set the virtual IP address of VRRP backup group 10 to 10.0.0.1/24, and set the priority
of VRRP backup group 10 to 110.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
7 Dual-System HSB Configuration
319
Advertisement
Table of Contents
