Table of Contents
Advertisement
S9700 Core Routing Switch
Configuration Guide - SPU
l
l
l
Procedure
Step 1 Configure traffic importing on the Switch.
1.
2.
3.
Issue 01 (2012-03-15)
Name and action of the load balancing action profile
Name of the Layer 3 classifier and ACL and Layer 7 classifier bound to the Layer 3 classifier
Name of the load balancing policy and interface where the load balancing policy is applied
Import traffic to the SPU on the Switch.
<Switch> system-view
[Switch] vlan batch 12 13 14
[Switch] interface gigabitethernet 3/0/0
[Switch-GigabitEthernet3/0/0] port link-type trunk
[Switch-GigabitEthernet3/0/0] port trunk allow-pass vlan 12
[Switch-GigabitEthernet3/0/0] undo port trunk allow-pass vlan 1
[Switch-GigabitEthernet3/0/0] quit
[Switch] interface gigabitethernet 3/0/1
[Switch-GigabitEthernet3/0/1] port link-type trunk
[Switch-GigabitEthernet3/0/1] port trunk allow-pass vlan 13
[Switch-GigabitEthernet3/0/1] undo port trunk allow-pass vlan 1
[Switch-GigabitEthernet3/0/1] quit
[Switch] interface gigabitethernet 3/0/2
[Switch-GigabitEthernet3/0/2] port link-type trunk
[Switch-GigabitEthernet3/0/2] port trunk allow-pass vlan 14
[Switch-GigabitEthernet3/0/2] undo port trunk allow-pass vlan 1
[Switch-GigabitEthernet3/0/2] quit
[Switch] interface xgigabitethernet5/0/0
[Switch-XGigabitEthernet5/0/0] port link-type trunk
[Switch-XGigabitEthernet5/0/0] port trunk allow-pass vlan 12 to 14
[Switch-XGigabitEthernet5/0/0] undo port trunk allow-pass vlan 1
[Switch-XGigabitEthernet5/0/0] quit
Configure an NAT address pool on the SPU.
<Quidway> system-view
[Quidway] sysname SPU
# Configure an NAT address pool with the index being 2 and the network segment ranging
from 20.20.20.3 to 20.20.20.200.
[SPU] nat address-group 2 20.20.20.3 20.20.20.200
# Configure an NAT address pool with the index being 3 and the network segment ranging
from 30.30.30.3 to 30.30.30.200.
[SPU] nat address-group 3 30.30.30.3 30.30.30.200
Add an interface to a VLAN on the SPU.
[SPU] interface xgigabitethernet 0/0/1.12
[SPU-XGigabitEthernet0/0/1.12] control-vid 12 dot1q-termination
[SPU-XGigabitEthernet0/0/1.12] dot1q termination vid 12
[SPU-XGigabitEthernet0/0/1.12] ip address 10.10.10.1 255.255.255.0
[SPU-XGigabitEthernet0/0/1.12] arp broadcast enable
[SPU-XGigabitEthernet0/0/1.12] quit
[SPU] interface xgigabitethernet 0/0/1.13
[SPU-XGigabitEthernet0/0/1.13] control-vid 13 dot1q-termination
[SPU-XGigabitEthernet0/0/1.13] dot1q termination vid 13
[SPU-XGigabitEthernet0/0/1.13] ip address 20.20.20.2 255.255.255.0
[SPU-XGigabitEthernet0/0/1.13] arp broadcast enable
[SPU-XGigabitEthernet0/0/1.13] service load-balance
group
2
[SPU-XGigabitEthernet0/0/1.13] quit
[SPU] interface xgigabitethernet 0/0/1.14
[SPU-XGigabitEthernet0/0/1.14] control-vid 14 dot1q-termination
[SPU-XGigabitEthernet0/0/1.14] dot1q termination vid 14
[SPU-XGigabitEthernet0/0/1.14] ip address 30.30.30.2 255.255.255.0
[SPU-XGigabitEthernet0/0/1.14] arp broadcast enable
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
6 Load Balancing Configuration
arp-response nat address-
232
Advertisement
Table of Contents
