Setting The Operation Mode Of The [All] Button In The Transition Control Block; Setting Trackball, Joystick, Search Dial, And Double-Click Sensitivity - Sony MVS-8000X User Manual

[CUT] buttons in the transition control block,
press [Auto Trans/Cut Swap], turning it on.
Transition preview operation mode: For the
operation mode of the [TRANS PVW] button,
select [Lock] or [Hold] in the <Trans Pvw> group.
The setting as to whether to use the "One-time
mode" in which the transition preview terminates
when the transition completes, or to use button
control, is made on the switcher side (see page
218).
[KEY] button operation mode for key source bus
operations: When the key source bus is selected
with the delegation buttons in the auxiliary bus
control block, specify the [KEY] button operation
mode in the <Key Source Bus Select Mode>
group, as follows.
• Key: If you select this, the [KEY] button is
always lit, and this mode allows only key signals
to be selected with the cross-point buttons.
• Video & Key: The [KEY] button is enabled,
and either video or key signals can be selected.
CCP-6000/8000-specific button settings: Press
[CCP-6000/8000 Button], and skip to step 3. This
setting is enabled when the CCP-6224/6324 is
used.
3
If required, make the following settings.
Operation mode during a fade-to-black: To set the
operation mode if the [FTB] button is pressed once
more during a fade-to-black, select either of the
following in the <FTB> group.
• Continue: Continue the fade-to-black.
• Cancel: Cancel the fade-to-black, and return to
the state before executing the fade-to-black.
Operation mode of the [XPT HOLD] buttons in the
key rows: Set the operation mode of the [XPT
HOLD] buttons in the key rows in the <Key Bus
Xpt Hold> group, as follows.
• Normal: The <Xpt Hold Mode> in the Switcher
>Key/Wipe/FM/CCR menu is enabled.
• Protect: In this mode, pressing a panel button
cannot change the cross-point settings.
Notes
The button On/Off state is preserved in each of the
"Normal" and "Protect" modes. For example, if
the [XPT HOLD] buttons are "On" in the Normal
mode, and you switch to Protect mode, then if the
[XPT HOLD] buttons were "Off" in this mode the
previous time, the [XPT HOLD] buttons go off,
and if they were "On" they light.
[UTIL] button operation mode: To set the operation
mode of the [UTIL] button in the cross-point
control block, press either of the following in the
<Util Button> group.
200
Operation Settings (Operation Menu)
• Hold: Acts as a utility button while held down,
changing the assignment of the cross-point
button rows.
• Lock: For the key rows, each time the button is
pressed the cross-point button assignment
toggles between the utility assignment and the
normal assignment. The background A and B
rows are fixedly assigned to the A and B rows,
even if the [UTIL] button is pressed.
Setting the Operation Mode of the
[ALL] Button in the Transition
Control Block
Specify the next transition selected by pressing the [ALL]
button in the transition control block.
Notes
If everything here is set to Off, then pressing the [ALL]
button does not change the specification of the next
transition.
1
In the Panel >Operation >Custom Button menu, press
[Next Trans All].
The Next Trans All menu appears.
2
Press the button for the next transition you want to
select with the [ALL] button, turning it On.
Setting Trackball, Joystick, Search
Dial, and Double-Click Sensitivity
You can set the operational sensitivity for trackball,
joystick and the buttons which recall the relevant menus
when pressed twice, and the relation between the rotation
angle of the search dial with the playback speed.
1
In the Panel >Operation menu, press the [Sensitivity].
The Sensitivity menu appears.
The status area shows a list of the items with their
settings.
2
Make the following settings as required.
Trackball and Z-ring sensitivity in normal mode:
In the <Trackball Normal Mode> group, select
[×1], [×2], or [×4].
Trackball and Z-ring sensitivity in fine mode: In the
<Trackball Fine Mode> group, select [
1
or [ / ].
8
Joystick sensitivity in normal mode: In the <Joystick
Normal Mode> group, select [×1], [×2], or [×4].
1 1
/ ], [ / ],
2 4