Sony MVS-8000X User Manual page 285

Icon Message
Clip frame number can't be ODD in
720P format (–9).
File Frame Memory
Some requests are skipped.
Following operation is not permitted.
— Loading that will cause duplicate
register name.
File Open Status
ERROR (01)
ERROR (02)
ERROR (FF): No target device has
been assigned
GPI Input
Please set Target.
Please set Trigger Type.
Please set Reg No.
Please set Aux Bus No.
Please set Src No.
GPI Output
Please set Target.
Please set Trigger Type.
Please set Reg No.
Please set Pulse Width.
Please set Pulse Timing.
HDD Format
Success!!
Success!!
System will be restarted.
Success!!
But some partitions cannot be created
because the capacity of the HDD is
not enough.
Failure.
HDD device is busy.
In order to complete HDD format,
System needs to be restarted and
formatted again.
System will be restarted, then please
execute HDD format again.
No external HDD was found (–2).
Format operation failed (–11).
Cannot access the partition (–12).
Description
2542: Frame Memory >File >Auto Extraction
When [Extraction Start] was pressed, an odd number of clips were extracted
(720P format only).
7151: File >Frame Memory
7162: File >All, External File >Import/Export
An attempt was made to load a file with the same name as a file already in
the register.
533X: Device >DDR/VTR
An error was returned from the DDR/VTR, and one of the messages on the
left appears, depending on the error number.
Use menu 7355 (Engineering Setup >DCU >Serial Port Assign) or menu
7325.4 (Engineering Setup >Panel >Device Interface >DCU Serial Port/
MPE Assign) to check the device settings.
7325.1/2: Engineering Setup >Panel >Device Interface >GPI Input
7337.2/3: Engineering Setup >Switcher >Device Interface >GPI Input
7344.1/2: Engineering Setup >DME >Device Interface >DME1 GPI Input
7344.4/5: Engineering Setup >DME >Device Interface >DME2 GPI Input
7352/7352.1: Engineering Setup >DCU >GPI Input Assign
An incorrect parameter setting value was specified. Check the settings, and
try again.
7325.3: Engineering Setup >Panel >Device Interface >GPI Output
7337.4: Engineering Setup >Switcher >Device Interface >GPI Output
7344.3: Engineering Setup >DME >Device Interface >DME1 GPI Output
7344.6: Engineering Setup >DME >Device Interface >DME2 GPI Output
7354: Engineering Setup >DCU >GPI Output Assign
An incorrect parameter setting value was specified. Check the settings, and
try again.
2561: Frame Memory >External Device >Ext HDD Format
Formatting of the external hard disk was completed successfully.
7317: Engineering Setup >System >Maintenance
Formatting of the hard disk was completed successfully. Press [OK] to
restart the system.
7317: Engineering Setup >System >Maintenance
Formatting of the hard disk was completed successfully.
However, because of insufficient hard disk capacity, only the possible
number of partitions were created.
7317: Engineering Setup >System >Maintenance
Formatting of the hard disk failed. If the hard disk is functioning correctly, or
in some cases when there is damage to the disk, it may not be possible to
format the disk correctly in a single attempt. In such cases, it is necessary to
restart the system, and then carry out formatting again. Press [OK] to restart
the system.
2561: Frame Memory >External Device >Ext HDD Format
When [5 Partition] or [15 Partition] was pressed, the external hard disk could
not be found. Check that the external hard disk is correctly connected.
2561: Frame Memory >External Device >Ext HDD Format
When [5 Partition] or [15 Partition] was pressed, formatting of the hard disk
failed.
2561: Frame Memory >External Device >Ext HDD Format
When [5 Partition] or [15 Partition] was pressed, the external hard disk
logical drive could not be accessed. Check that the external hard disk is
correctly formatted.
285
Error Messages