Auxiliary Bus Control Block Settings (Aux Assign Menu); Assigning A Bus To An Aux Delegation Button; Using The Auxiliary Bus Control Block For Router Control - Sony MVS-8000X User Manual

Auxiliary Bus Control
Block Settings (Aux
Assign Menu)
To carry out the settings of the AUX delegation buttons in
the auxiliary bus control block, use the Panel >Aux Assign
menu.
When using the AUX panel-less function with the CCP-
6224/6324, use this menu to assign the AUX delegation
buttons.
To display the Aux Assign menu
In the Engineering Setup menu, select VF2 'Panel' and
HF3 'Aux Assign.'
The left side of the status area shows the delegation
numbers, and the list of buses set; the right side shows a list
of buses that can be assigned.
The following functions are available here.
• Aux Assign: Assign the AUX delegation buttons in the
auxiliary bus control block to any bus.
• Shift Mode: Specify whether the rightmost button of the
AUX delegation buttons is used as a shift button, and
when it is used as a shift button, the operation mode.
• RTR Mode Setting: Carry out the following settings for

using the auxiliary bus control block for router control.

- Assigning destinations
- Setting the shift operation in the destination selection
button rows
- Source table settings
- Setting the shift operation in the source selection
button rows
- Assigning levels to the level selection buttons
- Setting destination selection buttons to be used for
snapshots
Notes
When using the AUX panel-less function with the
CCP-6224/6324, these settings are invalid.
Assigning a Bus to an AUX
Delegation Button
1
In the Panel >Aux Assign menu, using any of the
following methods, select the delegation button and
the bus to be assigned.
• Press directly on the list in the status area.
• Press the arrow keys to scroll the reverse video
cursor.
• Turn the knobs.
Knob Parameter Adjustment
1 Deleg No Selection of AUX
delegation button
2 Bus No Selection of bus
to be assigned
a) The setting can be from 1 to 62. The valid settings, however, depend
on the number of buttons and the delegation button shift mode.
Number of Shift mode
buttons
16 OFF
ON
24 OFF
ON
32 OFF
ON
b) The buses that can be assigned are as follows.
In M/E-x, the x is the M/E bank number (1 to 5); in DSKx the x is the
DSK number (1 to 8); in Keyx the x is the key number (1 to 8).
Edit Preview, Aux1 to Aux48, Frame Memory Source1 and Frame
Memory Source2, DME1V to DME8V, DME1K to DME8K, P/P
Utility1 and P/P Utility2, M/E-x Utility1 to M/E-x Utility2, DSKx
Fill/Source, M/E-x Keyx Fill/Source, P/P EXT DME, M/E-x EXT
DME, DME Utility1 and DME Utility2, CCR1 and CCR2
• For a button for which you want to disable operation,
press [Inhibit].
2
Press [Set] to confirm the selection.
To set the AUX delegation button shift operation
To set the operation mode of the rightmost button in the
row of AUX delegation buttons, select one of the
following in the <Shift Mode> group of the Panel >Aux
Assign menu.
Hold: Acts as a shift button, and the shifted version of the
AUX delegation buttons is enabled while the button is
held down.
Lock: Acts as a shift button, and pressing the button
toggles between the shifted version and the unshifted
version of the AUX delegation buttons.
Off: Acts as an AUX delegation button. In a 16-button
system it acts as button number 16, in a 24-button
system as button number 24, and in a 32-button system
as button number 32.
Using the Auxiliary Bus Control
Block for Router Control
To make router control settings, display the Panel >Aux
Assign >RTR Mode Setting menu.
To display the RTR Mode Setting menu
1
In the Engineering Setup menu, select VF2 'Panel' and
HF3 'Aux Assign.'

Auxiliary Bus Control Block Settings (Aux Assign Menu)

Setting values
a)
1 to 128
b)
1 to 185
Valid settings
1 to 16
1 to 30
1 to 24
1 to 46
1 to 32
1 to 62
181