Cueup & Play - Sony MVS-8000X User Manual

Operating When VTR is used When video disk
status
display
Local The REMOTE/
LOCAL switch of
the device is set to
LOCAL.
Tape Out No tape is loaded.
Rec Recording.
Cue> Cueing up in the
forward direction.
Cue< Cueing up in the
reverse direction.
Eject Ejecting cassette.
Stb Off Stopped in standby
off mode.
Stop Stopped in standby
on mode.
Play Playing.
FF Fast forwarding.
Rewind Rewinding.
Shtl> Playing in the
forward direction in
shuttle mode.
Shtl< Playing in the
reverse direction in
shuttle mode.
Var> Playing in the
forward direction in
variable mode.
Var< Playing in the
reverse direction in
variable mode.
Jog> Playing in the
forward direction in
jog mode.
Jog< Playing in the
reverse direction in
jog mode.
Still Playing still image.
a) Not supported for Extended VTR.
b) Not supported for the Odetics protocol.
Current: Shows timecode for current device position.
Start TC: Shows timecode for start point set on device.
Stop TC: Shows timecode for stop point set on device.
Variable: Shows the variable speed set for each device.
Delay: Shows start delay time set on device.
Mode: Shows operation mode (Loop or Recue) set for the
device.
20
Control of VTRs, Extended VTRs, and Disk Recorders
Cueup & Play
communications
protocol, Extended
You can use the device control block or Device menu to
VTR, Sony disk 9-
save Cueup & Play settings (start point timecode, stop
pin protocol, or
Odetics protocol is
point timecode, start delay time, and so on) for a VTR, disk
used
recorder or Extended VTR in an effect register. By
Port is not open. recalling this register, you can operate the following
buttons in the keyframe control block to automatically
control the VTR, disk recorder or Extended VTR.
[REWIND] button: Cue up to the start point timecode
b)
No file loaded.
[RUN] button: Play
a) b)
Recording. With this function you can also stop the VTR, disk
recorder or Extended VTR used for playback at the stop
—
point timecode recalled from the same register.
—
Disk recorder (video disk communications
protocol) operation when loop /recue is set
—
When loop is set: playback repeatedly between the start
—
When recue is set: when playback reaches the stop point,
Stopped.
Playing.
Notes
—
• In an effect register set on the VTR/disk recorder
—
timeline, Cueup & Play settings are not possible. To add
Cueup & Play settings to such a register, first clear the
—
VTR/disk recorder timeline setting before carrying out
the operation.
• When using a disk recorder with Cueup & Play, if you
—
carry out the following sequence of operations, the
system may freeze on the frame of the start point.
1. Press the [RUN] button to play to a point close to the
Playing in the
forward direction in
variable mode.
2. Stop playback.
Playing in the
3. Press the [RUN] button once more.
reverse direction in
In such cases, first recall a different register, then carry
variable mode.
out the following sequence:
Playing in the
1. Recall the original register again.
forward direction in
2. Press the [REWIND] button.
jog mode.
3. Press the [RUN] button.
Playing in the
reverse direction in
Making and saving settings relating to
jog mode.
Cueup & Play
—
1
2
point and stop point.
automatically cue up to the start point.
end of a file.
Press the [EFF] button in the numeric keypad control
block, turning it on.
This assigns the numeric keypad control block to
keyframe operations, and the [RCALL] button lights.
Press the region selection button for the region for
which you want to make the setting, turning it on.
You can select more than one button.