Sony MVS-8000X User Manual page 281

Icon Message
Activate License
License key was successfully entered.
The license will be activated after
rebooting your system.
The license key you entered is invalid.
Please check and enter again.
Append Key Frame
[Append Key Frame] cannot be
executed.
FMx is not assigned to a user region.
[Append Key Frame] cannot be
executed.
Key Frame Register is locked. (UserX)
[Append Key Frame] cannot be
executed.
Key Frame Register is busy. (UserX)
[Append Key Frame] cannot be
executed.
Key Frame Register is being edited.
(UserX)
[Append Key Frame] cannot be
executed.
Key Frame Register is full. (UserX)
[Append Key Frame] cannot be
executed.
Key Frame Register is not active.
(UserX)
Backup
Success!!
Success!!
But the number of folder exceeds the
limit (12) and the files expected for the
folders were backed up in the default
folder.
Or the name was changed because it
was the same file name.
External HDD Backup/Restore is
running (–2).
FM file auto extraction is running (–3). 2564: Frame Memory >External Device >Backup to DDR/VTR
Clip is recording (–4).
FM DDR/VTR Backup/Restore is
running (–5).
No external HDD was found (–2).
Description
7316.7: Engineering Setup >System >Install/Unit Config >License >License
Management
The Activate License procedure was completed successfully.
7316.7: Engineering Setup >System >Install/Unit Config >License >License
Management
The Activate License procedure failed because the entered information was
incorrect. Check the license key, and enter again.
2515: Frame Memory >Still >Create Key Frame
When [Append Key Frame] was pressed, the frame memory output (FMx)
was not assigned to a User region.
Assign the output in menu 7331.4 (Engineering Setup >Switcher >Config
>User1–8 Config), and try again.
2515: Frame Memory >Still >Create Key Frame
When [Append Key Frame] was pressed, the key frame register (UserX
region) was locked. Unlock the register.
2515: Frame Memory >Still >Create Key Frame
When [Append Key Frame] was pressed, files were being loaded into
register (UserX region). Try again after file loading has finished.
2515: Frame Memory >Still >Create Key Frame
When [Append Key Frame] was pressed, keyframe creation or editing was
in progress using the register (UserX region). Try again after the keyframe
operation has finished.
2515: Frame Memory >Still >Create Key Frame
When [Append Key Frame] was pressed, there were no remaining
keyframes in the register (UserX region).
2515: Frame Memory >Still >Create Key Frame
When [Append Key Frame] was pressed, the region selection button for a
register in the numeric keypad control block was not selected. Select the
region selection button [UserX] in the numeric keypad control block, and try
again.
2562: Frame Memory >External Device >Ext HDD Backup/Restore
Saving files into the external hard disk was completed successfully.
2562: Frame Memory >External Device >Ext HDD Backup/Restore
Saving files into the external hard disk was completed successfully.
However, the limit on the number of folders was reached, and therefore files
were backed up in the default folder. Alternatively, the file name was
changed because a file of the same name already exists.
2564: Frame Memory >External Device >Backup to DDR/VTR
When [Backup Start] was pressed, a backup/restore operation to/from the
external hard disk was in progress.
When [Backup Start] was pressed, extraction of frame memory file data to
the VTR was in progress.
2564: Frame Memory >External Device >Backup to DDR/VTR
An external device was recording clips.
2564: Frame Memory >External Device >Backup to DDR/VTR
When [Backup Start] was pressed, a backup/restore operation to/from the
VTR/DDR was in progress.
2562: Frame Memory >External Device >Ext HDD Backup/Restore
When [Backup] was pressed, the external hard disk could not be found.
Check that the external hard disk is correctly connected.
281
Error Messages