AudioCodes Mediant 800B User Manual page 190
Media gateway & enterprise session border controller (e-sbc)
Hide thumbs
Also See for Mediant 800B:
- User manual (1338 pages) ,
- Installation and maintenance manual (104 pages) ,
- Hardware installation manual (56 pages)
Table of Contents
Advertisement
c.
Set the 'V.23 Modem Transport Type' parameter to Enable Bypass
(V23ModemTransportType = 2).
d.
Set the 'V.32 Modem Transport Type' parameter to Enable Bypass
(V32ModemTransportType = 2).
e.
Set the 'V.34 Modem Transport Type' parameter to Enable Bypass
(V34ModemTransportType = 2).
2.
Set the ini file parameter, V34FaxTransportType to 2 (Bypass).
14.2.3.2 Relay Mode for T.30 and V.34 Faxes
In this scenario, V.34 fax machines are forced to use their backward compatibility with T.30
faxes and operate in the slower T.30 mode.
To use T.38 mode for V.34 and T.30 faxes:
1.
In the Fax/Modem/CID Settings page, do the following:
a.
Set the 'Fax Transport Mode' parameter to T.38 Relay (FaxTransportMode = 1).
b.
Set the 'V.22 Modem Transport Type' parameter to Disable
(V22ModemTransportType = 0).
c.
Set the 'V.23 Modem Transport Type' parameter to Disable
(V23ModemTransportType = 0).
d.
Set the 'V.32 Modem Transport Type' parameter to Disable
(V32ModemTransportType = 0).
e.
Set the 'V.34 Modem Transport Type' parameter to Disable
(V34ModemTransportType = 0).
2.
Set the ini file parameter, V34FaxTransportType to 1 (Relay).
To allow V.34 fax relay over T.38:
In the Advanced Parameters page (Configuration tab > VoIP menu > SIP Definitions >
Advanced Parameters), set the 'SIP T.38 Version' parameter to Version 3
(SIPT38Version = 3).
To force V.34 fax machines to use their backward compatibility with T.30 faxes
and operate in the slower T.30 mode:
Set the 'SIP T.38 Version' parameter to Version 0 (SIPT38Version = 0).
14.2.3.3 V.34 Fax Relay for SG3 Fax Machines
Super Group 3 (SG3) is a standard for fax machines that support speeds of up to 33.6
kbps through V.34 half duplex (HD) modulation. The following procedure describes how to
configure V.34 (SG3) fax relay support based on ITU Specification T.38 version 3.
To enable support for V.34 fax relay (T.38) at SG3 speed:
1.
In the IP Profile table (Configuration tab > VoIP menu > Coders and Profiles > IP
Profile Settings), configure an IP Profile with the 'Fax Signaling Method' parameter
(IpProfile_IsFaxUsed) set to T.38 Relay.
2.
In the Coders Table (Configuration tab > VoIP menu > Coders and Profiles >
Coders), set the coder used by the device to G.729 (or any other supported codec).
3.
On the Fax/Modem/CID Settings page, do the following settings:
a.
'SIP T.38 Version' to Version 3 (SIPT38Version = 3).
b.
'Fax Relay Max Rate' (RelayMaxRate) to 33,600bps (default).
c.
'CNG Detector Mode' (CNGDetectorMode) to Disable (default).
d.
'V.21 Modem Transport Type' to Disable (V21ModemTransportType = 0).
User's Manual
Mediant 800B Gateway and E- SBC
190
Document #: LTRT-10296
Advertisement
Table of Contents
