H: Terminal Functions; H: Terminal Functions; H1: Multi-Function Digital Inputs - YASKAWA T1000V Technical Manual

5.7

H: Terminal Functions

H parameters are used to assign functions to the external terminals.

◆ H1: Multi-Function Digital Inputs

H1-01 to H1-06: Functions for Terminals S1 to S6
■
These parameters assign functions to the multi-function digital inputs. The settings 0 to 7E determine function for each
terminal and are explained below.
Note: If not using an input terminal or if using the through-mode, set that terminal to "F".
No.
H1-01 Multi-Function Digital Input S1 Terminal Function Selection
H1-02 Multi-Function Digital Input S2 Terminal Function Selection
H1-03 Multi-Function Digital Input S3 Terminal Function Selection
H1-04 Multi-Function Digital Input S4 Terminal Function Selection
H1-05 Multi-Function Digital Input S5 Terminal Function Selection
H1-06 Multi-Function Digital Input S6 Terminal Function Selection
<1> Number appearing in parenthesis is the default value after performing a 3-Wire initialization.
Setting
0 3-Wire Sequence
1 LOCAL/REMOTE Selection
2 External Reference 1/2
3 Multi-Step Speed Reference 1
4 Multi-Step Speed Reference 2
5 Multi-Step Speed Reference 3
6 Jog Reference Selection
7 Accel/Decel Time 1
8 Baseblock Command (N.O.)
9 Baseblock Command (N.C.)
A Accel/Decel Ramp Hold
B Drive Overheat Alarm (oH2)
C Terminal A1/A2 Enable/Disable
F Not used/Through Mode
10 Up Command
11 Down Command
12 Forward Jog
13 Reverse Jog
14 Fault Reset
15 Fast-Stop (N.O.)
16 Motor 2 Selection
17 Fast-stop (N.C.)
18 Timer Function Input
19 PID Disable
1A Accel/Decel Time Selection 2
1B Program Lockout
<1> This setting is valid from software versions 6000 or later.
YASKAWA ELECTRIC SIEP C710606 44B YASKAWA AC Drive T1000V Technical Manual
Parameter Name
Table 5.16 Digital Multi-Function Input Settings
Function
Setting
Range
1 to 7E 40 (F): Forward Run Command (2-wire sequence)
1 to 7E 41 (F): Reverse Run Command (2-wire sequence)
0 to 7E 24: External Fault
0 to 7E 14: Fault Reset
0 to 7E 3 (0) : Multi-Step Speed Reference 1
<1>
0 to 7E 4 (3) : Multi-Step Speed Reference 2
<1>
Page Setting
160 20 to 2F External Fault
160 30 PID Integral Reset
161 31 PID Integral Hold
34 PID Soft Starter Cancel
161 35 PID Input Level Selection
40 Forward Run/Stop (2-wire sequence)
161 41 Reverse Run/Stop (2-wire sequence)
161 42 Run/Stop (2-Wire sequence 2)
43 FWD/REV (2-Wire sequence 2)
161
44 Offset Frequency 1 Addition
161 45 Offset Frequency 2 Addition
161 46 Offset Frequency 3 Addition
162 47 Node Setup
<1>
162 50 Disturb Function Cancel
51 Synchronous Accel/Decel
162
53 Energy Saving On/Off
59 DC Injection Braking 1
163
60 DC Injection Braking 2
163 61 External Speed Search Command 1
163 62 External Speed Search command 2
164 65 KEB 1 (N.C.)
163 66 KEB 1 (N.O.)
164 67 Communications Test Mode
164 7C Short-Circuit Braking (N.O.)
164 7D Short-Circuit Braking (N.C.)
Forward/Reverse Detection (V/f Control with
164 7E
Simple PG Feedback)

5.7 H: Terminal Functions

Default
Function Page
165
165
165
165
165
165
166
166
166
166
166
166
166
167
167
5
167
167
167
167
168
159