E: Motor Parameters - YASKAWA T1000V Technical Manual

B.3 Parameter Table

◆ E: Motor Parameters

No. Name
E1-01 Input Voltage
Setting
<17>
V/f Pattern
E1-03
Selection
Maximum Output
E1-04
Frequency
E1-05
Maximum Voltage
<17>
E1-06 Base Frequency
Middle Output
E1-07
Frequency
E1-08 Middle Output
Frequency Voltage
<17>
Minimum Output
E1-09
Frequency
E1-10 Minimum Output
Frequency Voltage
<17>
E1-11 Middle Output
Frequency 2
<19>
Middle Output
E1-12
Frequency Voltage
<17> <19>
2
E1-13
Base Voltage
<17>
E2-01 Motor Rated
Current
<34>
E2-02 Motor Rated Slip
Motor No-Load
E2-03
Current
Number of Motor
E2-04
Poles
Motor Line-to-Line
E2-05
Resistance
Motor Leakage
E2-06
Inductance
Motor Iron-Core
E2-07 Saturation
Coefficient 1
Motor Iron-Core
E2-08 Saturation
Coefficient 2
330
Description
E1: V/f Pattern for Motor 1
Use E1 parameters to set V/f characteristics for the motor.
This parameter must be set to the power supply voltage.
WARNING! Drive input voltage (not motor voltage)
must be set in E1-01 for the protective features of the
drive to function properly. failure to do so may result in
equipment damage and/or death or personal injury.
F: Custom V/f. E1-04 through E1-13 settings define the
V/f pattern.
To set linear V/f characteristics, set the same values for
E1-07 and E1-09. In this case, the setting for E1-08 will
be disregarded. When E1-13 = 0.0 V, then the drive uses
the value set to E1-05 to control the voltage level. Ensure
that the four frequencies are set according to these rules:
E1-04 ≥ E1-06> E1-07 ≥ E1-09
VACrms Out(V)
E1-05
E1-12
E1-13
E1-08
E1-10
E1-09 E1-07
Frequency (Hz)
E2: Motor Parameters
Use E2 parameters to set motor-related data.
Sets the motor nameplate full load current in amperes
(A).
Automatically set during Auto-Tuning.
Sets the motor rated slip in Hertz.
Automatically set during rotational Auto-Tuning.
Sets the magnetizing current of the motor in Ampere.
Automatically set during rotational Auto-Tuning.
Sets the number of motor poles. Automatically set during
Auto-Tuning.
Sets the phase-to-phase motor resistance in ohms.
Automatically set during Auto-Tuning.
Sets the voltage drop due to motor leakage inductance as
a percentage of motor rated voltage.
Automatically set during Auto-Tuning.
Sets the motor iron saturation coefficient at 50% of
magnetic flux. Automatically set during Auto-Tuning.
Sets the motor iron saturation coefficient at 75% of
magnetic flux. Automatically set during Auto-Tuning.
Range
155 to 255
0.0 to 255.0
0.0 to E1-
0.0 to E1-
0.0 to 255.0
0.0 to E1-
0.0 to 255.0
0.0 to E1-
E1-06 E1-11 E1-04
0.0 to 255.0
0.0 to 255.0
10 to 200%
of drive
0 to less
than E2-01
0.000 to
0.0 to 40.0
0.00 to 0.50 0.50%
[E2-07] to
YASKAWA ELECTRIC SIEP C710606 44B YASKAWA AC Drive T1000V Technical Manual
Control
Mode
Def.
V/f OL V PM
200 V S S
F F A A
40.0 to
50.0 Hz
400.0 S S
<2> <9>
<14>
200.0 V
S S
<2> <9>
50.0 Hz
S S
04
<2> <9>
2.5 Hz
A A
04
<2>
16.0 V
A A
<2>
1.3 Hz
S S
04
<2> <9>
12.0 V
A A
<2>
0.0 Hz
A A
04
<2>
0.0 V
A A
<2>
0.0 V
A S
<2>
rated S S
<33>
current
<20>
0.00 to
A A
<33>
20.00
A A
<33>
2 to 48 4 poles A A
65.000 A A
<33>
<23>
A A
<33>
−
A
−
0.75% A
0.75
Addr. Hex Pg.
S 300 147
−
302 147
S 303 148
S 304 148
S 305 148
− 306 148
−
307 148
S 308 148
−
309 148
− 30A 148
−
30B 148
−
30C 148
−
30E 148
−
30F 149
−
310 149
− 311 149
− 312 149
−
313 149
−
314 150
−
315 150