YASKAWA T1000V Technical Manual page 352

B.3 Parameter Table
No. Name
n8-74
Id No Load Start
<38>
n8-75
Id No Load End
<38>
n8-76
Id Filter Time
<38>
n8-77
Id Load Slp End
<38>
n8-78
Id Medium Value
<38>
n8-87 Output Voltage Limit
Selection
<38>
n8-88 Output Voltage Limit
Switch Current Level
<38>
n8-89 Output Voltage Limit
Switch Hysteresis Width
<38>
n8-90 Output Voltage Limit
Switch Speed
<38>
n8-91 Output Voltage Limit ld
Limit
<38>
n9-10 AVR Time Constant
On-Delay Compensation
n9-12
Time
On-Delay Compensation
n9-62
Derating Start Frequency
On-Delay Compensation
n9-63
Disable Frequency
<9> Default setting is determined by the motor code set to parameter E5-01.
<11> Default setting is determined by the drive model selection set in parameter o2-04.
<15> Parameter can be changed during run.
<17> Values shown here are for 200 V class drives. Double the value when using a 400 V class drive.
<38> This parameter is valid from software version 6002 or later. This setting rarely needs to be changed from its default value.
<39> Setting range varies by the software version the drive is running. Software versions 6002 or later allow this value to be changed during run.
Software versions 6002 or later: 0%, 20 to 200%
Software versions 6001 or earlier: 20 to 200%
<40> Setting range varies by the software version the drive is running. Software versions 6002 or later allow this value to be changed during run.
Software versions 6002 or later: -200.0 to 200.0%
Software versions 6001 or earlier: -200.0 to 0.0%
<46> Setting range is determined as follows: (n8-74 + 0.1%) to (n8-50 - 0.1%).
<47> Setting range is determined as follows: (n8-50 + 0.1%) to 250.0%.
352
Description
Sets Id current level 1 for light loads.
Note: An Operator Programming Error (oPE) occurs if the
setting value deviates from the following condition: n8-
74≤n8-75≤n8-50.
Sets Id current level 2 for light loads.
Note: An Operator Programming Error (oPE) occurs if the
setting value deviates from the following condition: n8-
74≤n8-75≤n8-50.
Sets Id filter time for PM OLV control mode.
Sets Id current level for high loads.
Sets Id current level for medium loads.
Sets how the output voltage limit should be used.
Sets the current level to switch the output voltage limit
sequence. Set as a percentage of the motor rated current
(E5-03).
Sets hysteresis used for the current level that switches the
output voltage limit sequence. Set as a percentage of the
motor rated current (E5-03).
Sets the speed level for switching the output voltage limit
sequence. Set as a percentage of the maximum output
frequency (E1-04).
Sets the limit value for the ld operation of the feedback type
output voltage limitation. This setting is available only at
n8-87 = 0.
n9: Hardware Settings
Using these parameters, drive output voltage can be adjusted.
Sets a delay time for output voltage compensation.
Sets the time value used for IGBT On-delay compensation.
Sets the frequency at which the drive begins to compensate
the output voltage for the IGBT On-Delay.
Sets the frequency at which the drive stops compensating
the output voltage for the IGBT On-Delay.
YASKAWA ELECTRIC SIEP C710606 44B YASKAWA AC Drive T1000V Technical Manual
Control
Mode
Range Def.
V/f OL V P M
0.0 to
30.0% − − A
250.0%
50.0% − − A
<46>
0 to 5000 200
− − A
ms ms
90.0% − − A
<47>
-200.0 to
0.0% − − A
200.0%
− − A
0,1 0
0 to 400% 400% − − A
− − A
0 to n8-88 3%
0 to 200% 200% − − A
0 to -
-50% − − A
200%
0.0 to 1.0
A A A
100.0 ms
0.00 to
A A A
<11>
20.00
0.0 to
0.0
[E1-04] A A A
Hz
Hz
0.0 to
0.0
[E1-04] A A A
Hz
Hz
Addr.
Pg.
Hex
5C3 211
5C4 211
5CD 211
5CE 211
5F4 211
2BC 211
2BD 211
2BE 211
2BF 211
2F7 212
SD9 210
SDB 210
64F 210
650 210