Page 1
HDQ 2K40 User and Installation manual R5905303/09 02/03/2015...
Page 2
Barco nv Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.82.11 Fax: +32 56.36.883.86 Support: www.barco.com/esupport Visit us at the web: www.barco.com Printed in Belgium...
Page 3
GNU-GPL code If you would like a copy of the GPL source code contained in this product shipped to you on CD, please contact Barco. The cost of preparing and mailing a CD will be charged. Guarantee and Compensation Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee.
Read this chapter attentively. It contains important information to prevent personal injury while installing and using a Barco HDQ 2K40. Furthermore, it includes several cautions to prevent damage to the HDQ 2K40. Ensure that you understand and follow all safety guidelines, safety instructions and warnings mentioned in this chapter before installing your HDQ 2K40. After this chapter, additional “warnings”...
SONNEL, AUTHORIZED to operate professional projection systems. A Barco HDQ 2K40 is intended "FOR PROFESSIONAL USE ONLY" by AUTHORIZED PERSONNEL familiar with potential hazards associated with high voltage, high intensity light beams, ultraviolet exposure and high temperatures generated by the lamp and associated circuits.
Page 13
ARNING The complete exhaust box is very hot when the projector is on. To avoid burns, let the projector cool down for at least 15 minutes before touching the exhaust box. R5905303 HDQ 2K40 02/03/2015...
Page 14
In the event of fire, use sand, CO electrical fire. Always have service performed on this projector by authorized Barco service personnel. Always insist on genuine Barco replacement parts. Never use non-Barco replacement parts as they may degrade the safety of this projector.
If the product exhibits a distinct change in performance, indicating a need for service. • Replacement parts: When replacement parts are required, be sure the service technician has used original Barco replacement parts or authorized replacement parts which have the same characteristics as the Barco original part. Unauthorized substitu- tions may result in degraded performance and reliability, fire, electric shock or other hazards.
Page 16
On image 1-1 a typical setup is displayed. It must be verified by the installer if these minimum requirements are met. If required a restricted zone (RZ) in the theater must be established. This can be done by using physical barrier, like a red rope as illustrated in image 1-2. Image 1-2 R5905303 HDQ 2K40 02/03/2015...
1. Safety HD in function of the lens Throw Ratio (TR) TR (Throw Ratio) The ratio of the distance to the screen (throw) to the screen width. HDQ 2K40 Hazard Distance HDF-W30 HDF-W26 HDF-W22 10,3 11,0 11,8 12,5 13,3 14,0...
Read this chapter before installing your Barco HDQ 2K40. It contains important information concerning installation requirements for the HDQ 2K40, such as minimum and maximum allowed ambient temperature, humidity conditions, required safety area around the installed projector, required power net, etc.
Page 20
Main Power requirements The HDQ 2K40 operates from a nominal 230/400V 3W+N+PE 16A 50-60Hz or 208V 3W+PE 27A 50-60Hz. The projector must be switched internally between a star connection to a delta connection or vice versa. See "Y-Δ (wye-delta) configuration of the projector", page 28.
2. Unfold the top side of the outer cardboard box. Take out the small box located between inner and outer cardboard box (this box contains the accessories such as manuals, remote control, etc.). Remove the outer cardboard box by sliding it up above the projector. R5905303 HDQ 2K40 02/03/2015...
Page 22
Release the projector from the supporting wooden board by removing the 4 screws. Warning: It is forbidden to lift up the projector with manpower, use a hoisting tool instead. Do not underestimate the weight of the projector. The projector weights ±220 kg (±485 lb.). R5905303 HDQ 2K40 02/03/2015...
Save all packing material until the inspection is completed. If damage is found, file claim with carrier immediately. The Barco Sales and Service office should be notified as soon as possible.
Air inlets and outlets Air inlets and outlets Image 2-6 The HDQ 2K40 projector has 3 air inlets (1 at the front and 2 at the bottom) and 2 air outlets (on the exhaust box on top of the projector). ARNING When the projector is used in portrait mode, the air outlet is positioned towards the floor.
After you have unpacked and checked the projector you can start with the installation process of your Barco HDQ 2K40. This chapter gives you an overview of all the different stages in the installation process which you have to follow to set your HDQ 2K40 up and running.
Page 26
See chapter "Connecting a UPS to the projector electronics", page 31. 6. Physical installation of the projector. Position your HDQ 2K40 in landscape or portrait mode, see chapter "Landscape and portrait mode", page 33. If necessary, choose to stack multiple projectors, either in a standing (table mount) or hanging (ceiling mount) configuration, see chapter "Stacking multiple projectors", page 35.
The batteries are not placed in the remote control unit to avoid control operation in its package, resulting in a shorter battery life time. At delivery the batteries can be found in a separated bag attached to the remote control unit. Before using your remote control, install the batteries first. R5905303 HDQ 2K40 02/03/2015...
How to install the rugged case of the remote control ? 1. Slide the bottom of the RCU into the rugged case and then pull the top of the rugged case over the top of the RCU as illustrated. R5905303 HDQ 2K40 02/03/2015...
1. Connect a cable with XLR plug into the XLR adaptor. 2. Connect the other end of the cable with your HDQ 2K40. 3. Push the XLR adaptor completely against the rugged case of the remote control unit, as illustrated in the left image below, for wired communication.
RCU with rugged case and XLR adaptor The RCU will send the commands via the cable connected with the XLR pushed in “WIRED” and wired adaptor to the projector. Backlight illuminates continuously when wire is connected. Infra red disabled. Image 3-8 R5905303 HDQ 2K40 02/03/2015...
5. Secure the Lamp House by fastening the two retaining screws (1) at the base of the Lamp House. Use a 10 mm nut driver or a flat screwdriver. Image 3-10 Installation of the Lamp House 6. Install the lamp cover. R5905303 HDQ 2K40 02/03/2015...
For a 3W+N+PE system, 400V is measured between the lines (L1, L2, L3) and 230V is measured between the lines and the neutral (L1–N, L2–N, L3–N). For a 3W+PE system, 208V is measured between the lines (L1–L2, L2–L3, L3–L1). R5905303 HDQ 2K40 02/03/2015...
Page 33
Note: Link A and link B must be mounted together, above each other. 6. Mount the third link (C) between the middle (5) and lower (6) pin. 7. Install the 6 top nuts and tighten to a torque of 7.5 Nm. R5905303 HDQ 2K40 02/03/2015...
6. Connect each wire of the power cable with the terminal barrier strip (3), according to the legend on the decal (4). Tighten the screws to a torque of 1.4 Nm. Warning: Always connect ground conductor (PE) first. Note: Always connect the neutral conductor (N) when available. R5905303 HDQ 2K40 02/03/2015...
UPS. A short power link cable (with plug type C13/C14) loops the power through to the projector electronics. ARNING Only use UPS units which are suitable for the HDQ 2K40. How to connect a UPS to the projector electronics? 1.
Page 36
While squeezing, slide the fixation spring on the pins and push it against the power plug. c) Release the fixation spring. Tip: Install the second fixation spring on the power outlet socket to prevent losing it. Image 3-18 R5905303 HDQ 2K40 02/03/2015...
Example: the projector is positioned in landscape mode and is rotated in the frame for 3°. An additional frame rotation of 12° of is allowed. Landscape and portrait mode The projector can be used in landscape or portrait mode. The illustrations below shows which positions are allowed and which are not. R5905303 HDQ 2K40 02/03/2015...
Page 38
It is not allowed to stack multiple projectors in portrait mode. AUTION When the projector is used in portrait mode, always ensure the cooling liquid level is sufficient. To check the cooling liquid level, see "Checking cooling liquid level", page 301. R5905303 HDQ 2K40 02/03/2015...
Introduction The Barco HDQ 2K40 is mounted by default in a multifunctional frame. This frame can be used to stack multiple projectors onto each other. The stacked projectors can be used in a standing (table mount) or hanging configuration (ceiling mount).
Page 40
The projector weights ±220 kg (±485 lb.). 4. Slide in the 4 pipe lynch pins (3) and secure them by swinging the lever (4). Image 3-22 Stacking projectors 5. Mount 2 (two) safety cables to secure both projector frames to each other: R5905303 HDQ 2K40 02/03/2015...
Image 3-23 Adjusting the multifunctional frame Introduction The Barco HDQ 2K40 is mounted by default in a multifunctional frame. This frame can be used to adjust the projector position. The frame can be adjusted in 3 different ways: • inclinating •...
Page 42
2. Turn the adjustment rod (2) clockwise to skew the projector clockwise anti clockwise to skew the projector anti clockwise. 3. Tighten the locking screw(s) (1). Use a 2.5 mm Allen wrench. Tip: Only secure the most reachable locking screw(s). R5905303 HDQ 2K40 02/03/2015...
Adjust until the outline of the hatch pattern is most symmetric with the projection screen. Inclination Image 3-28 4. Adjust the skew of the projector. Adjust until the outline of the hatch pattern is most symmetric with the projection screen. R5905303 HDQ 2K40 02/03/2015...
See "Adjusting the multifunctional frame", page 37. Reference projector In case of a standing configuration (table mount), this is the lowest projector. In case of a hanging configuration (ceiling mount), this is the uppermost projector. R5905303 HDQ 2K40 02/03/2015...
Page 45
Note: The “Shift” function is motorized, which means that you have to access the projector software, via the local keypad or remote control unit, to operate the “Shift” function. See "Lens adjustment, shift", page 176. R5905303 HDQ 2K40 02/03/2015...
Page 46
“Focus” function. See "Lens adjustment, zoom - focus", page 175. In case of a triple stacked standing projector configuration (table mount) adjust and align the reference pro- jector first, than the middle projector and finally the uppermost projector. R5905303 HDQ 2K40 02/03/2015...
XLR input port for remote control RS232/RS422 input port Dual Link DVI-I HDCP input Free input slot Button module Optional antenna for GSM RS232/RS422 input port Ethernet port Status and indication LEDs USB port 3G/Dual/HDSDI input - output Free input slot R5905303 HDQ 2K40 02/03/2015...
4. Input & Communication Input source connections DVI and 3G/HDSDI input This input module is standard delivered with the Barco HDQ 2K40. R9864000 3G/DUAL HDSDI DUAL LINK DVI-I HDCP SYNC SYNC SYNC OUT2 INPUT OUT1 Image 4-2 Dual Link DVI and 3G/Dual HDSDI input The yellow LED lights up when valid input sync is detected.
Page 49
BNC socket. Generates 3D synchronization signal to drive an infra red transmitter for active 3D glasses. In case an 3D syn- chronization signal is applied on the “3D SYNC IN” for a single channel 3D stream then the generated 3D output sync is derived from this applied sync. Input specifications R5905303 HDQ 2K40 02/03/2015...
You can use the DMX input port to connect a DMX device (DMX console) to the projector. This way you can control the projector from that DMX device (console). The DMX output port can be connected with the next device in the loop. Description Earth R5905303 HDQ 2K40 02/03/2015...
Page 51
The left one a Sub-D connector, the right one an USBB connector acting as RS input when connected to an USB input of a PC. You can use the RS232/RS422 input to connect a local PC to your Barco HDQ 2K40. By this way you can configure and control your Barco HDQ 2K40 from your local PC.
When a 100 MB network is detected IR received but not acknowledged green IR received and acknowledged orange WIFI sel When WiFi is selected green When WiFi is connected with an Ethernet See chapter “Getting started”, topic “Status LEDs” R5905303 HDQ 2K40 02/03/2015...
Page 53
4. Input & Communication Function Color Description orange See chapter “Getting started”, topic “Status LEDs” orange See chapter “Getting started”, topic “Status LEDs” R5905303 HDQ 2K40 02/03/2015...
Page 54
4. Input & Communication R5905303 HDQ 2K40 02/03/2015...
About this chapter This chapter gives an overview of available lenses for the Barco HDQ 2K40 and explains how you can select the best suited lens for your specific situation using the lens formulas. Also, it is explained how to install and remove a lens from the projector lens holder.
How to select the right lens 1. Determine the required screen width (SW). 2. Determine the approximate position of the projector in the room. 3. Start up the Lens Calculator on the Barco website: http://www.barco.com/en/tools/lenscalculator to determine the possible lenses for your configuration.
2. Take the lens assembly out of its packing material and remove the lens caps on both sides. 3. Place the lens holder in the “unlocked” position by moving the lens lock handle (1) towards the lens power supply socket (2). Image 5-9 Unlock lens holder R5905303 HDQ 2K40 02/03/2015...
Page 58
8. Continue with the installation of the lens fixation mechanism, see "Installing the lens fixation mechanism", page 56. AUTION Never transport the projector with a Lens mounted in the Lens Holder. Always remove the Lens before transporting the projector. Neglecting this can damage the Lens Holder and Prism. R5905303 HDQ 2K40 02/03/2015...
It’s recommended to place the foam rubber of the original projector packaging, back into the Lens opening to prevent intrusion of dust. Note that this foam rubber is packed in a plastic bag to prevent the dust, emitted by the foam, from entering the projector. R5905303 HDQ 2K40 02/03/2015...
Necessary tools 10 mm wrench How to remove the lens fixation mechanism? 1. Remove the nuts (2) from the fixation brackets. Use a 10 mm wrench. 2. Remove the fixation brackets (1) from the Lens Holder. R5905303 HDQ 2K40 02/03/2015...
The zoom/focus menu opens. Image 5-16 Zoom/Focus adjustment 2. Use the ▲ or ▼ key to zoom the lens. Use the ◄ or ► key to focus the lens. Press ENTER to switch to Lens shift adjustment. R5905303 HDQ 2K40 02/03/2015...
Introduction The lens of the HDQ 2K40 can be shifted vertically. The maximum vertical shift range is ±110% in both directions, which is not sufficient in some situations. To extend the vertical shift range in a certain direction, the Lens Holder can be shifted manually.
DMD plane, the plane of sharp focus will also be tilted according to geometrical and optical properties. The DMD plane, the principal lens plane and the sharp focus plane will intersect in a line below the projector for downward lens tilt. R5905303 HDQ 2K40 02/03/2015...
Turn the Scheimpflug adjustment nuts 1, 2 and 3 until the front of the nut is equally aligned with the front of the threaded rod. b) Adjust the focus in the center of the screen (F) using the motorized focus control. R5905303 HDQ 2K40 02/03/2015...
Page 65
5. Lenses & Lens Holder Image 5-22 Center focusing 6. Sharpen bottom left corner of the screen by adjusting nut 1. Image 5-23 Left bottom focusing 7. Sharpen bottom right corner of the screen by adjusting nut 2. R5905303 HDQ 2K40 02/03/2015...
When fixing the Lens Holder front plate After performing the procedure for Scheimpflug adjustment or Back Focal Length adjustment the Lens Holder front plate must be secured in such a way that it doesn’t disturb the result of the adjustment. R5905303 HDQ 2K40 02/03/2015...
Page 67
Note: Ensure that the edges of the projected test pattern remain in place on the screen. Any movement of the image will affect the Scheimpflug adjustment. Tip: Fasten the set screw and the Scheimpflug nut alternately, without disturbing the projected image, until the Scheimpflug nut and set screw are completely tightened. R5905303 HDQ 2K40 02/03/2015...
Page 68
5. Lenses & Lens Holder Image 5-28 7. Fasten the lock nut at the lower left of the Lens Holder. Use a 10mm nut driver. R5905303 HDQ 2K40 02/03/2015...
• switching to "pause" (blanked picture, full power for immediate restarting) • direct access to all connected sources. Terminology overview Overview The following table gives an overview of the different functionality of the keys. R5905303 HDQ 2K40 02/03/2015...
Page 70
Use these buttons to obtain the desired picture level. PHASE Used to remove the horizontal instability of the image (usually for RGB source). It adjusts the phase of the pixel sampling clock relative to the incoming signal. FREEZE To freeze the actual projected image. R5905303 HDQ 2K40 02/03/2015...
The projector starts up in standby. The menus are accessible via the local LCD panel. The start up screen is displayed on the local LCD panel and when fully started up, it changes to the overview screen. R5905303 HDQ 2K40 02/03/2015...
Page 72
• number of Strikes • Run time in hours • Remaining run time in hours • slide bar indication with percentage indication of the current run time, compared with the maximum life time of the lamp. R5905303 HDQ 2K40 02/03/2015...
Standby key indication The projector starts up on the last saved source. The LMP LED on the communication interface lights up. Some lamp and runtime warnings can be displayed when an image is displayed after a start up. R5905303 HDQ 2K40 02/03/2015...
Shutter is closed, projector in standby Full white Shutter is undefined (shutter not open and not closed) Full white toggles Shutter is closed during reset formatter on/off PWR (power Projector powers up LED) Standby Orange ECO standby Green Projector is on R5905303 HDQ 2K40 02/03/2015...
IR sensor. Image 6-7 IR sensors Projector Address 6.8.1 Displaying and Programming addresses into the RCU Displaying the Projector Address on the Screen. 1. Press Address key (recessed key on the RCU) with a pencil. R5905303 HDQ 2K40 02/03/2015...
Use the digit keys on the remote control or local keypad to activate the desired source. Source selection when picture in picture is active Use the Window button on the remote control or the local keypad to select the main window or the picture in picture (PiP) window. R5905303 HDQ 2K40 02/03/2015...
Page 77
To select the source for the picture in picture window, press Window button until PiP window is activated and then select the desired source with the digit keys. To select the source for the main window, press Window button until the main window is activated and then select the desired source with the digit keys. R5905303 HDQ 2K40 02/03/2015...
Page 78
6. Getting started R5905303 HDQ 2K40 02/03/2015...
To toggle Text ON or OFF, press the TEXT key on the remote control or local keypad. Quick Lens Adjustment via LENS key Quick zoom/focus adjustment 1. Press the LENS key on the remote control or local keypad to open the Zoom/Focus Adjustment menu. R5905303 HDQ 2K40 02/03/2015...
Page 80
3. When finished, press EXIT key to return or ENTER to continue to the shift adjustment. Press the LENS key to call the list with available test patterns. Quick shift adjustment 1. Press the LENS key on the remote control or local keypad to open the Zoom/Focus Adjustment menu. R5905303 HDQ 2K40 02/03/2015...
On the Remote Control four buttons with double action are provided, allowing direct alignment for lens ZOOM, FOCUS, HORIZON- TAL SHIFT and VERTICAL SHIFT. 1. Press LENS ZOOM button [-] or [+] (A) for correct image size on the screen. R5905303 HDQ 2K40 02/03/2015...
Select Main full screen to switch off PIP. Image 7-7 Load layout file list Quick language selection Quick language selection via the remote control When no OSD menu is visible on the screen, press the Info button (1) on the remote control. R5905303 HDQ 2K40 02/03/2015...
Page 83
1. Press Menu to activate the menus and select Projector Control → Change Language. 2. Press ENTER to open the language selection menu. 3. Select the desired language with the ▲ ▼ key and press ENTER to activate. The current active language is indicated with a selected radio button R5905303 HDQ 2K40 02/03/2015...
Page 84
7. Quick set up adjustment Image 7-10 Main menu Image 7-11 Projector Control Image 7-12 Change language R5905303 HDQ 2K40 02/03/2015...
To start up the adjustment mode, use the remote control or the local keypad. How to start up? 1. Press Menu on the remote control (RCU) or on the local keypad to start up the Adjustment mode. R5905303 HDQ 2K40 02/03/2015...
Image 8-2 Use the ◄ or ► key to directly adjust the current value. Via bar scale adjustment : Once an item is selected, press ENTER to open the bar scale menu. Image 8-3 Contrast adjustment R5905303 HDQ 2K40 02/03/2015...
Scroll to the desired menu. Press the digit key behind which the menu must be stored for 5 seconds. When the creation is success- fully, a confirmation message appears on the screen. E.g. : Image 8-5 Select Yes to confirm the creation. To erase the shortcut, navigate to Projector Control → Buttons. R5905303 HDQ 2K40 02/03/2015...
MENU EXIT ENTER Image 8-7 Info button When no information is available for the selected item, the message No help available for this item is displayed. To return to the adjustment mode, press EXIT. R5905303 HDQ 2K40 02/03/2015...
Input 2 DUAL SDI Input Locking Input on Main Window Input on Pip Window Input 1 Input 2 Input 3 Input 4 Free Run Free Run Options Minimum delay Native Resolution [On/Off] No Signal Color [black/blue] R5905303 HDQ 2K40 02/03/2015...
1. Press Menu to activate the menus and select Input → Input Selection. 2. Press ENTER. The Select Source menu is displayed with the actual available sources filled out. 3. Use the ▲ or ▼ key to select an input. Image 9-1 Main window Image 9-2 Input selection R5905303 HDQ 2K40 02/03/2015...
3. Use the ▲ or ▼ key to select an input Press ENTER to open the selection menu which will be different from input type to input type. Image 9-4 Main window Image 9-5 Advanced input settings R5905303 HDQ 2K40 02/03/2015...
AUTO mode, then the Color Space must be selected as no automatic detection is possible. Use the ▲ or ▼ key to select the correct color space and press ENTER to select. Image 9-8 Color space selection for AUTO R5905303 HDQ 2K40 02/03/2015...
HDMI - DisplayPort input (3D input module) How to select Select HDMI/DP and press ENTER to open the selections Image 9-13 HDMI-Display port selection Use the ▲ or ▼ key to select the desired input and press ENTER to select. R5905303 HDQ 2K40 02/03/2015...
Output is locked on input 2 Input 3 Output is locked on input 3 Input 4 Output is locked on input 4 Free run Output is locked on an internal sync (60 Hz or manual setup) R5905303 HDQ 2K40 02/03/2015...
To ensure minimum delay in the other processing steps, make sure warping is OFF, the resolution of the input source is native and the input locking is set to the main input. How to toggle the delay 1. Press Menu to activate the menus and select Input → Minimum delay [On]. R5905303 HDQ 2K40 02/03/2015...
When the show native resolution function is in the ON position, the projector handles the source as follows: Source Projected image Name Ratio Resolution Ratio Resolution 1024x768 1024x768 image projected with black borders SXGA 1280x1024 1280x1024 image projected with black borders SXGA+ 1400x1050 1400x1050 image projected with black borders R5905303 HDQ 2K40 02/03/2015...
9.7.1 Background color How to set the background color 1. Press Menu to activate the menus and select Input → No Signal. → Color. 2. Press ENTER to toggle between [Blue] or [black]. R5905303 HDQ 2K40 02/03/2015...
How to activate logo 1. Press Menu to activate the menus and select Input → No Signal. → Logo. 2. Press ENTER to toggle between [On] or [Off]. Image 9-27 Main window Image 9-28 Input, no signal R5905303 HDQ 2K40 02/03/2015...
The retarding time is the time between no signal is detected and the moment that the projector shuts down. How to set the retarding time 1. Press Menu to activate the menus and select Input → No Signal. → Shutdown time (min). R5905303 HDQ 2K40 02/03/2015...
How to set up 1. Press Menu to activate the menus and select Input → No Signal. → Auto Dimming. Image 9-36 Main window Image 9-37 Input, no signal R5905303 HDQ 2K40 02/03/2015...
Selecting the Standard EDID file or an own created file can be selected from the list of Custom EDID files for the input. How to configure 1. Press Menu to activate the menus and select Input → EDID → Configure. 2. Press ENTER to open the EDID configuration menu. R5905303 HDQ 2K40 02/03/2015...
Page 103
Your selection is applied and stored for this input. The EDID Configuration menu remains open to configure another input. use the ▲ or ▼ key to select OK. Your selection is applied and stored for this input and the EDID configuration menu is closed. R5905303 HDQ 2K40 02/03/2015...
5. Select the calculation method to obtain the correct (standard) video timings. Possible selections: CVT: Coordinated Video Timings CVT RB: Coordinated Video Timings Reduced Blanking CVT MB: Coordinated Video Timings Minimum Blanking (not a standard) GTF: Generalized Timing Formula R5905303 HDQ 2K40 02/03/2015...
How to delete 1. Press Menu to activate the menus and select Input → EDID → Delete. 2. Press ENTER to open the EDID list with custom files. Image 9-49 Main window Image 9-50 Input, EDID R5905303 HDQ 2K40 02/03/2015...
Delete all custom EDID file Standard EDID files cannot be deleted. How to delete 1. Press Menu to activate the menus and select Input → EDID → Delete All. 2. Press ENTER to open the confirmation window. R5905303 HDQ 2K40 02/03/2015...
MENU > Input > 3D > L/R Synchronisation > Field Dominance [L/R] or [R/L] Example: A DisplayPort source with a frequency of 120 Hz consisting of content for the left and right eye results in a 60 Hz video per eye. R5905303 HDQ 2K40 02/03/2015...
Page 108
MENU > Input > 3D > Frame Sequential – Dual channel Possible sources: 2 x DVI , 2 x SDI. If two 3D Input Modules are installed: 2 x HDMI or 2 x DisplayPort. SENSIO Hi-Fi 3D ® Image 9-58 SENSIO ® HI-FI 3D decoding R5905303 HDQ 2K40 02/03/2015...
2048x1080@60Hz. 2048x1080@60Hz. 2048x1080@60Hz. Interlaced/progressive Interlaced/progressive Interlaced/progressive Interlaced/progressive Top-and-Bottom Max. resolution: Max. resolution: Max. resolution: Max. resolution: 1920x1200@60Hz or 1920x1200@60Hz or 1920x1200@60Hz or 1920x1200@60Hz or 2048x1080@60Hz. 2048x1080@60Hz. 2048x1080@60Hz. 2048x1080@60Hz. Progressive only Progressive only Progressive only Progressive only R5905303 HDQ 2K40 02/03/2015...
3. For SDI (3G- Level B), IN1 or IN2 of the SDI input can be used. The input settings under MENU -> Input -> Advanced Settings -> SDI/HDSDI/3G must be set to ‘Input 1’ or ‘Input 2’, with or without Priority R5905303 HDQ 2K40 02/03/2015...
SENSIO ® 3D Decoder – FFC How to activate/deactivate 1. Press Menu to activate the menus and select Input → 3D → Auto detection. 4. NA:feedback from SENSIO Autodetect is not applicable in thes cases ® R5905303 HDQ 2K40 02/03/2015...
Top-and-Bottom (Half): One input contains 3D information with half of the resolution. • SENSIO 3D Decoder - FFC: HDMI/DisplayPort (only on 3D input module). ® • Line Alternating (3G-B): SDI only How to select 1. Press Menu to activate the menus and select Input → 3D R5905303 HDQ 2K40 02/03/2015...
This selection is only possible when a 2 channel 3D input is chosen. How to make selection 1. Press Menu to activate the menus and select Input → 3D → Second input. Image 9-68 Image 9-69 Main window Input, 3D R5905303 HDQ 2K40 02/03/2015...
flashing is introduced and the coupling between the video input signal and the 3D SYNC IN signal must be determined. This setting is stored per input. How to activate 1. Press Menu to activate the menus and select Alignment → 3D Glasses → L/R Synchronisation. Image 9-72 Image 9-73 Main window Input, 3D R5905303 HDQ 2K40 02/03/2015...
What can be done? This menu allows to set the 3D emitter output signal. With Invert 3D sync out we can swap the left and right 3D sync to eliminate a 3D output mismatch with the 3D emitters. R5905303 HDQ 2K40 02/03/2015...
Page 116
Right Image 9-76 3D sync out How to toggle 3D SYNC OUT 1. Press Menu to activate the menus and select Alignment → 3D Glasses → L/R Synchronisation. Image 9-77 Image 9-78 Main window Input, 3D R5905303 HDQ 2K40 02/03/2015...
Page 117
[On] : 3D SYNC OUT is the inverted version of the 3D sync signal generated by the processing, allowing to swap left and right eye on the active glasses. [Off] : 3D SYNC OUT is a copy from the 3D sync signal generated by the processing. R5905303 HDQ 2K40 02/03/2015...
Computer 9300K Video 6500K Film 5400K Broadcast 3200K Custom Balance Input Balance Black Balance White Balance Defaults Aspect ratio 16:9 2.35 1.88 1.85 1.78 1.67 16:10 Custom Timings Horizontal Total Pixels Active pixels Horizontal start Period R5905303 HDQ 2K40 02/03/2015...
The contrast function is used to adjust the contrast between the light and the dark areas of the displayed image. It applies a gain to the red, green and blue signals. Contrast adjustment can be done with the Contrast key on the RCU or via the menu structure. R5905303 HDQ 2K40 02/03/2015...
Brightness adjustment can be done with the Brightness key on the RCU or via the menu structure. How to adjust 1. Press Menu to activate the menus and select Image → Image Settings → Brightness. R5905303 HDQ 2K40 02/03/2015...
The saturation function is used to adjust the color saturation levels. Saturation adjustment can be done with the Saturation key on the RCU or via the menu structure. How to adjust 1. Press Menu to activate the menus and select Image → Image Settings → Saturation. R5905303 HDQ 2K40 02/03/2015...
When displaying computer patterns or graphics (RGB or YUV signals) which are very detailed (tilting, vertical stripes, etc. ), jitter in picture (mis-sampling) may occur, causing horizontal stripes in portions of the screen. When this jitter occurs, adjust ’Phase’ for optimum image. R5905303 HDQ 2K40 02/03/2015...
Page 124
2. Press ENTER to select. Image 10-19 Phase adjustment 3. To change the value directly in the Image Settings window, use the ◄ or ► key or a numeric key 0-9, to adjust as a % of the full range. R5905303 HDQ 2K40 02/03/2015...
1. Press Menu to activate the menus and select Image → Image Settings → Color Temperature. Image 10-21 Image adjustments Image 10-20 Main menu, Image Image 10-22 Image settings, color temperature 2. Press ENTER to select. The color temperature selection menu is displayed. R5905303 HDQ 2K40 02/03/2015...
Next to these 5 fixed temperatures, a custom setup is also possible. 10.3.6 Color temperature (custom values) How to set up 1. Press Menu to activate the menus and select Image → Image Settings → Color Temperature. Image 10-26 Image adjustments Image 10-25 Main menu, Image R5905303 HDQ 2K40 02/03/2015...
Another value that is subject to alteration is the amplitude of the signal, resulting in an altered “Gain” of the signal (“white level” or contrast). The alterations of the three color signals will happen independently i.e. the colors will end to be unbalanced, image 10-30 0.7V Black level Image 10-29 R5905303 HDQ 2K40 02/03/2015...
The source in question must be able to generate a white signal, ideally a 100% white (background) full screen pattern The source in question must be able to generate a black signal, ideally a 100% black (background) full screen pattern R5905303 HDQ 2K40 02/03/2015...
Page 129
Image 10-33 How to adjust 1. Press Menu to activate the menus and select Image → Image Settings → Input Balance. Image 10-35 Image adjustments Image 10-34 Main menu, Image R5905303 HDQ 2K40 02/03/2015...
Page 130
Performing White input balance 1. Connect the source you want to project. 2. Press Menu to activate the menus and select Image → Image Settings → Input Balance. Image 10-39 Image adjustments Image 10-38 Main menu, Image R5905303 HDQ 2K40 02/03/2015...
With the defaults button, all image settings for a specific source are returned to the default values. How to return to the defaults 1. Press Menu to activate the menus and select Image → Image Settings → Defaults. R5905303 HDQ 2K40 02/03/2015...
Can also be expressed as a decimal number, such as 1.77. The larger the ratio or decimal, the wider the image (or the less the image is squared). What can be done? The aspect ratio setting forces the projector to project an image using a defined aspect ratio. Aspect ratio Description Standard television format R5905303 HDQ 2K40 02/03/2015...
Page 133
1. Press Menu to activate the menus and select Image → Aspect Ratio. Image 10-48 Image, aspect ratio Image 10-47 Main menu, Image 2. Press ENTER to select. 3. Use the ▲ or ▼ key to select the desired aspect ratio. R5905303 HDQ 2K40 02/03/2015...
If not, adjust until full image height is displayed (no missing lines). • Total pixels: Total horizontal pixels in the source. If the value is wrong, sampling mistakes (small vertical bars in the projected image) will be seen in the image. R5905303 HDQ 2K40 02/03/2015...
The time between the trailing edge of the sync pulse and the leading edge of the clamp pulse, in pixels. Can be any value between 0 and 255. Clamp width The width of the clamp pulse can be any value between 0 and 255. R5905303 HDQ 2K40 02/03/2015...
Page 136
1. Press Menu to activate the menus and select Image → Timings → Advanced settings. Image 10-57 Image, timings Image 10-56 Main menu, Image Image 10-58 Timings, advanced settings 2. Press ENTER to select. Image 10-59 Clamp delay R5905303 HDQ 2K40 02/03/2015...
[All] : full list with all available files in the projector. How to set up 1. Press Menu to activate the menus and select Image → Image File Services → File Load Filter. Image 10-65 Image, image file services Image 10-64 Main menu, Image R5905303 HDQ 2K40 02/03/2015...
2. Press ENTER to select. The available custom files are displayed. If no custom files are available, a message that no custom files are available is displayed. 3. Use the ▲ or ▼ key to select the file to delete. R5905303 HDQ 2K40 02/03/2015...
Main menu, Image Image 10-73 Delete all custom files If no custom files are available, a message that no custom files are available is displayed. 2. Use the ▲ or ▼ key to select Yes or No. R5905303 HDQ 2K40 02/03/2015...
5. Press ENTER to finalize the rename action. 10.6.7 Copy custom file How to copy 1. Press Menu to activate the menus and select Image → Image File Services → Copy. Image 10-81 Image, image file services Image 10-80 Main menu, Image R5905303 HDQ 2K40 02/03/2015...
Page 143
Note: Digits can be entered with the digit keys on the remote control or the local keypad. When a digit is entered in that way, the next character will be selected automatically. Arrow key left (◄) has the backspace functionality. R5905303 HDQ 2K40 02/03/2015...
10.6.9 Image file service options, Auto Picture Alignment How to set 1. Press Menu to activate the menus and select Image → Image File Services → Options → Auto Picture Alignment. Image 10-91 Image, image file services Image 10-90 Main menu, Image R5905303 HDQ 2K40 02/03/2015...
1. Press Menu to activate the menus and select Image → Save Custom Settings Image 10-95 Image, save custom settings Image 10-94 Main menu, Image 2. Use the ▲ or ▼ key to select Yes and press ENTER. Image 10-96 Save custom settings, question R5905303 HDQ 2K40 02/03/2015...
A splash screen will be displayed at each startup for a certain time (time out) No splash screen is displayed at startup Time-out setup 1. Press Menu to activate the menus and select Image → Splash image Image 10-101 Image, splash image Image 10-100 Main menu, Image 2. Select Timeout(sec) R5905303 HDQ 2K40 02/03/2015...
Page 147
10. Image Image 10-102 Splash screen, time-out 3. Press ENTER to open the edit mode. Enter the time with 2 digits, e.g. 05 or 15. Note: Maximum timeout = 15 seconds. Image 10-103 Time-out, input R5905303 HDQ 2K40 02/03/2015...
Layout files determine the size and the position of the main and PiP window on the screen. Some pre-defined layouts are available in the projector but custom layouts can be created and saved for future use. A source number and lens settings can be associated with the layout settings. R5905303 HDQ 2K40 02/03/2015...
The radio button of the selected source is checked and the source is linked with the main window. 11.3.2 Main window size What can be done? The size of the main window can be adjusted until the desired window dimensions are reached. R5905303 HDQ 2K40 02/03/2015...
Page 151
How to change the size 1. Press Menu to activate the menus and select Layout → Main window → Size. Image 11-7 Layout, main window Image 11-6 Main menu, layout Image 11-8 Main window, size 2. Press ENTER to select. R5905303 HDQ 2K40 02/03/2015...
The main window can be repositioned on the screen. The upper left corner is the reference. Image 11-11 Positioning the window How to position 1. Press Menu to activate the menus and select Layout → Main window → Position. R5905303 HDQ 2K40 02/03/2015...
Select No if you want to quit without saving the current position. 11.4 PiP window Overview • Introduction to PIP • Picture in Picture activation • PiP window, source selection • PiP window, Size • PiP window, position R5905303 HDQ 2K40 02/03/2015...
3. Use the ▲ or ▼ key to select the desired source and press ENTER. The radio button of the selected source is checked and the source is linked with the PiP window. PiP source and main source can be the same input. R5905303 HDQ 2K40 02/03/2015...
Remark: During adjustment of the window size, scaling artifacts can be visible. Image 11-26 Size PIP window remark How to resize 1. Press Menu to activate the menus and select Layout → PiP window → Size. Image 11-28 Layout, PiP Window Image 11-27 Main menu, layout R5905303 HDQ 2K40 02/03/2015...
The picture in picture window can be positioned on any place on the display just by changing its start coordinates. The reference is the upper left corner of the window. How to position 1. Press Menu to activate the menus and select Layout → PiP window → Position. R5905303 HDQ 2K40 02/03/2015...
Page 158
A Save Layout window opens. Image 11-36 Save layout 5. Use the ▲ or ▼ key to select Yes and press ENTER to save. Select No if you want to quit without saving the current position. R5905303 HDQ 2K40 02/03/2015...
1. Press Menu to activate the menus and select Layout → Layout File Services → Delete All. Image 11-52 Layout, layout file services Image 11-51 Main menu, layout Image 11-53 Layout file services, delete all 2. Press ENTER to select. R5905303 HDQ 2K40 02/03/2015...
The Copy layout file window opens. If no custom layout files are available, a message that no custom layout files are available is displayed. Image 11-58 Copy layout 3. Use the ▲ or ▼ key to change the selected character. R5905303 HDQ 2K40 02/03/2015...
[No] = each layout will use its own zoom/focus/shift settings. Lens should be calibrated, when using this setting. 4. If [No] is selected, the calibrate lens menu opens. Image 11-62 Lens calibration R5905303 HDQ 2K40 02/03/2015...
Page 165
5. If you have to calibrate the lens, select Yes and press ENTER to start the calibration. During the calibration, a message is displayed. This message disappears when the calibration is finished. Image 11-63 Lens calibration message R5905303 HDQ 2K40 02/03/2015...
CLO mode. Once the CLO mode setting is switched to Off, the installed lamp power mode setting will be used. How to switch 1. Press Menu to activate the menus and select Lamp → Power → Mode. R5905303 HDQ 2K40 02/03/2015...
Within a certain power mode, the light output of the lamp can be reduced by reducing the lamp power How to reduce the power 1. Press Menu to activate the menus and select Lamp → Power → Power. Image 12-5 Lamp, power Image 12-4 Main menu, lamp R5905303 HDQ 2K40 02/03/2015...
1. Press Menu to activate the menus and select Lamp → Power → Auto Dimming when Pause. Image 12-8 Lamp, power Image 12-7 Main menu, lamp Image 12-9 Auto dimming when Pause 2. Press ENTER to toggle between [On] or [Off]. R5905303 HDQ 2K40 02/03/2015...
When an over-temperature is detected, the projector starts dimming the lamp so that the projector can cool down. How to set up 1. Press Menu to activate the menus and select Lamp → Power → Auto Dimming Overtemperature. R5905303 HDQ 2K40 02/03/2015...
In the illustration below, a normal light output curve is shown over the first 1000 hours, image 12-16. By using CLO and setting the target to 60% of the maximum light output, one will be able to operate during approximately 500 hours with a constant light output, image 12-17. R5905303 HDQ 2K40 02/03/2015...
Page 172
CLO mode setting On overrules the lamp power mode setting. Projector will always play in CLO mode using the CLO target. How to switch CLO mode 1. Press Menu to activate the menus and select Lamp → Power → CLO mode. Image 12-19 Lamp, power Image 12-18 Main menu, lamp R5905303 HDQ 2K40 02/03/2015...
2. Use the ◄ or ► key to change the CLO target lumens. Depending on the projector model, the value range can be different. The screenshot is only given as information. For the exact values, see the specifications of the specific projector. R5905303 HDQ 2K40 02/03/2015...
These parameters are useful in case of a service request. How to display 1. Press Menu to activate the menus and select Lamp → Identification. Image 12-26 Lamp, identification Image 12-25 Main menu, lamp 2. Press ENTER to select. R5905303 HDQ 2K40 02/03/2015...
How to display the light output 1. Press Menu to activate the menus and select Lamp → Z-axis. Image 12-29 Lamp, Z-axis Image 12-28 Main menu, lamp 2. Press ENTER to display the current light output. Image 12-30 Current light output R5905303 HDQ 2K40 02/03/2015...
Auto Rear Lens Zoom / Focus Shift Mid Position Calibrate lens at startup Calibrate lens Warping Warp adjust Opacity Warp file service Alternative Side Keystone Blanking Bottom Left Right Contrast/Intensity Intensity Gamma Internal Patterns Color Space Status R5905303 HDQ 2K40 02/03/2015...
1. Press Menu to activate the menus and select Alignment → Orientation. Image 13-1 Main menu, alignment Image 13-2 Alignment, orientation 2. Use the ▲ or ▼ key to select the desired orientation and press ENTER to activate. R5905303 HDQ 2K40 02/03/2015...
2. Use the ▲ or ▼ key to select zoom/focus and press ENTER to activate. Image 13-6 Lens, Zoom/Focus 3. Use the ▲ or ▼ key to zoom the lens. Use the ◄ or ► key to focus the lens. Press ENTER to switch to Lens shift adjustment. R5905303 HDQ 2K40 02/03/2015...
Lens, shift 3. Use the ▲ or ▼ key to shift the lens in vertical direction. Use the ◄ or ► key to shift the lens in horizontal direction. Press ENTER to switch to Zoom/Focus adjustment. R5905303 HDQ 2K40 02/03/2015...
Image 13-13 Alignment, lens 2. Use the ▲ or ▼ key to select Mid Position and press ENTER to activate. Image 13-14 Lens, mid position Lens will be shifted horizontally and vertically to its mid position. R5905303 HDQ 2K40 02/03/2015...
2. Use the ▲ or ▼ key to select Calibrate lens at startup and press ENTER to toggle between [on] and [off]. Image 13-17 Calibrate lens at startup 13.7 Calibrate lens Lens calibration is a time consuming operation. How to calibrate 1. Press Menu to activate the menus and select Alignment → Lens. R5905303 HDQ 2K40 02/03/2015...
A Lens Calibration window opens. Select first the desired calibration options by checking the check box before the option and then select Yes to start the calibration procedure. Image 13-21 Calibrate lens confirmation 13.8 Warping Not all models are equipped with a warping unit. For these models, the warping unit is optional. R5905303 HDQ 2K40 02/03/2015...
13.8.2 Warp activation - deactivation What can be done ? The Warp functionality can be activated or deactivated. With 3D activated, warping can be enabled for sources up to 30 Hz per eye. Above this frequency, warping is disabled. R5905303 HDQ 2K40 02/03/2015...
2. Press ENTER to toggle between [On] and [Off]. [On]: warp functionality is activated. [Off]: warp functionality is disabled. 13.8.3 Start up manual adjustment How to start up 1. Press Menu to activate the menus and select Alignment → Warping → .Warp adjust. R5905303 HDQ 2K40 02/03/2015...
Page 186
Increase the number of points. The current number of points (mode) is indicated with a digit inside the icon. By default 3 points are shown. Reduce the number of points. The current number of points (mode) is indicated with a digit inside the icon. Remove / show grid Remove / show points Hardware reset of warp module R5905303 HDQ 2K40 02/03/2015...
The impact depends on the level itself. Therefore it is important to adjust the geometry starting from level one and going down to lower levels as required. In practice it will not be needed to adjust the anchor points of levels 7 and lower. R5905303 HDQ 2K40 02/03/2015...
Page 188
1 1 1 Image 13-36 Geometry adjustment: 5 x 5 mode This logic can be extrapolated for the lower modes and levels, being level seven to level 21, however in practice these modes and levels are rarely used. R5905303 HDQ 2K40 02/03/2015...
How to select a predefined number of steps 1. Use the ▲ or ▼ key to go to the Warp adaptation steps area. The current selection is indicated in yellow. 2. Use the ◄ or ► key to select the desired steps. R5905303 HDQ 2K40 02/03/2015...
Warp mode. keystone, horizontal linearity, points, scale, shift, rotation, rotation point. Warp adaptation: this pane changes according to the warp mode selection. 2. Within a pane, use the ◄ or ► key to select the desired function. 3. Press ENTER to activate this function. R5905303 HDQ 2K40 02/03/2015...
2. Select the desired warp area. Depending on the selected area only the points in that area will be adjusted. 3. Select keystone. 4. Select within Warp Adaptations, Horizontal or Vertical to adjust the corresponding keystone. R5905303 HDQ 2K40 02/03/2015...
ENTER when an item is selected and use the 4 arrow keys to adjust. Image 13-45 Warping, Linearity 5. Adjust the horizontal and vertical linearity. To fine tune this adjustment, select a specific area and add extra anchor points by changing the warp level. R5905303 HDQ 2K40 02/03/2015...
How to scale 1. Select the 2 x 2 adjustment level. See "Setting the warping level", page 185. The default selected anchor point is the left top corner of the image. 2. Select the desired warp area. R5905303 HDQ 2K40 02/03/2015...
The image can be rotated around a predefined point. This is considered as an equal rotation of the 4 corner points in 2 x 2 mode and with the full area selected. The default rotation point is the center of the image. R5905303 HDQ 2K40 02/03/2015...
Page 195
Image 13-53 Warping, scaling 4. Continue with the rotation. Rotate around the rotation point 1. Select the 2 x 2 adjustment level. See "Setting the warping level", page 185. 2. Select full image as warp area. R5905303 HDQ 2K40 02/03/2015...
About the opacity of the OSD menus During the warp adjustment process the OSD menu is displayed on top the warp grid. To see the grid and the grid points, reduce the opacity of the OSD menu. R5905303 HDQ 2K40 02/03/2015...
Page 197
1. Press Menu to activate the menus and select Alignment → Warping → .Opacity. Image 13-58 Main menu, alignment Image 13-59 Alignment, Warping Image 13-60 Warping, opacity 2. Use the ◄ or ► key to change the opacity. R5905303 HDQ 2K40 02/03/2015...
Image 13-64 File service, load Image 13-63 Warping, file service 2. Press ENTER to display the overview list with warp files. Image 13-65 Warp files 3. Use the ▲ or ▼ key to select the desired file. R5905303 HDQ 2K40 02/03/2015...
What can be done? The current settings can be saved into a new file. How to save 1. Press Menu to activate the menus and select Alignment → Warping → .Warp File Service → .Save as. R5905303 HDQ 2K40 02/03/2015...
4. Press ENTER to finalize the save as action. 13.8.19 Warp file service, rename file How to rename? 1. Press Menu to activate the menus and select Alignment → Warping → .Warp File Service → .Rename. R5905303 HDQ 2K40 02/03/2015...
Arrow key left (◄) has the backspace functionality. 5. Press ENTER to finalize the rename action. 13.8.20 Warp file service, delete file How to delete 1. Press Menu to activate the menus and select Alignment → Warping → .Warp File Service → .Delete. R5905303 HDQ 2K40 02/03/2015...
13.8.21 Warp file service, delete all files What can be done? All custom created warp files can be deleted. How to delete 1. Press Menu to activate the menus and select Alignment → Warping → .Warp File Service → .Delete All. R5905303 HDQ 2K40 02/03/2015...
In some circumstances the hardware of the warping get stuck. A hard reset of the board is the only solution. With Warp board reset, the board is reset but the current values remain in the board. How to reset the board 1. Press Menu to activate the menus and select Alignment → Warping → .Warp board reset. R5905303 HDQ 2K40 02/03/2015...
How to reset board and values 1. Press Menu to activate the menus and select Alignment → Warping → .Warp board and values reset. R5905303 HDQ 2K40 02/03/2015...
For 3D sources with a frequency higher than 30 Hz/eye, the warp unit cannot be used anymore. Therefor, for these source the alternative side keystone can be used. How to adjust 1. Press Menu to activate the menus and select Alignment → Warping → .Alternative Side Keystone. R5905303 HDQ 2K40 02/03/2015...
(or noise). A ’0’ on the bar scale indicates no blanking. Which blanking adjustments are available ? • top blanking • bottom blanking • left blanking • right blanking R5905303 HDQ 2K40 02/03/2015...
Page 207
The reset function brings all blanking settings back to zero. How to adjust 1. Press Menu to activate the menus and select Alignment → Blanking. Image 13-101 Main menu, alignment Image 13-102 Alignment, blanking 2. Press ENTER to select. R5905303 HDQ 2K40 02/03/2015...
Alignment, contrast/intensity 2. Use the ▲ or ▼ key to select Intensity. Use the ◄ or ► key to change the intensity until the desired value is reached (adjustable between 0 and 255) Image 13-106 Intensity R5905303 HDQ 2K40 02/03/2015...
How to select a pattern 1. Press Menu to activate the menus and select Alignment → Internal Patterns. Image 13-109 Main menu, alignment Image 13-110 Alignment, internal patterns 2. Press ENTER to select the pattern list. R5905303 HDQ 2K40 02/03/2015...
This color space is measured at the factory and stored inside the projector. How to select a color standard 1. Press Menu to activate the menus and select Alignment → Color Space. R5905303 HDQ 2K40 02/03/2015...
Page 211
American standard. Custom The user can define the x and y coordinates for red, green and blue which forms the corners of the color space. By changing the coordinates, the color reproduction can be changed. Custom2 R5905303 HDQ 2K40 02/03/2015...
Why ScenergiX ? When working in a multichannel setup the HDQ 2K40 and its Soft Edge possibilities enable an image blending that gives the ap- pearance of a single view, thus achieving realistic immersion for the majority of wide screen applications.
To ensure proper ScenergiX adjustment, be sure that the following adjustments are done perfectly on all projectors: • Convergence • Geometry • Color Matching (Color Temperature, Color Standard, Input Balance, Gamma) 13.14.3 Scenergix activation How to activate 1. Press Menu to activate the menus and select Alignment → Scenergix. R5905303 HDQ 2K40 02/03/2015...
13.14.4 Scenergix pattern What can be done? To make the Scenergix adjustment more easy, an internal pattern can be displayed. How to select 1. Press Menu to activate the menus and select Alignment → Scenergix → Scenergix Pattern. R5905303 HDQ 2K40 02/03/2015...
10 50 90 130 170 210 250 290 330 370 Image 13-126 Scenergix pattern 13.14.5 Scenergix adjustment lines What can be done? Border lines for the blending areas can be displayed while adjusting the white and black level. R5905303 HDQ 2K40 02/03/2015...
When a source (A) must be displayed via 2 projectors as one image (B), the vertical and horizontal start position and the size must be determined so that each projector displays a part of the image. The overlap area can be adjusted with the Scenergix tools. R5905303 HDQ 2K40 02/03/2015...
Page 217
Activate data doubling on both projectors and setup the vertical and horizontal start for projector 1 and projector 2. How to setup 1. Press Menu to activate the menus and select Alignment → Scenergix → Data doubling. R5905303 HDQ 2K40 02/03/2015...
4. Do the same for Horizontal Size, Vertical Start and Vertical Size. 5. Repeat this action for he second projector. 13.14.7 White level adjustment (blending area) How to set 1. Press Menu to activate the menus and select Alignment → Scenergix → White level. R5905303 HDQ 2K40 02/03/2015...
Page 219
3. Use the ▲ or ▼ key to select one of the four size adjustments and press ENTER to select Use the ◄ or ► key to change the border of the blending area to the desired position (value between 0 and 255) R5905303 HDQ 2K40 02/03/2015...
Page 220
13. Alignment Image 13-139 Width selections 4. Set first the width for the first projector and repeat for the second one. Image 13-140 Width set up for projector 1 R5905303 HDQ 2K40 02/03/2015...
After the area is set, use TEXT key to remove the area border lines when adjusting the black level. How to set the leakage area width 1. Press Menu to activate the menus and select Alignment → Scenergix → Black level. R5905303 HDQ 2K40 02/03/2015...
Page 222
Image 13-146 Black level, area 3. Use the ▲ or ▼ key to select one of the four size adjustments. Use the ◄ or ► key to move the green border line to the desired position. R5905303 HDQ 2K40 02/03/2015...
Page 223
Use the Reset item to reset all area values. How to adjust 1. Press Menu to activate the menus and select Alignment → Scenergix → Black level. Image 13-148 Main menu, alignment Image 13-149 Alignment, Scenergix R5905303 HDQ 2K40 02/03/2015...
Image 1 Image 13-152 Black level adjustment Use the Reset item to set all values back to zero. 13.14.9 Scenergix Reset What can be done? All Scenergix values can be set back to the default values. R5905303 HDQ 2K40 02/03/2015...
The right image is projected, the right shutter is open, allowing the right eye to see the right image. The ideal situation is when the opening/closing times of these shutters are in sync with the blanking time of DLP mirrors. R5905303 HDQ 2K40 02/03/2015...
Page 226
Active Blanking Time Left Shutter Open Closed Right Shutter Open Closed Image 13-157 Shutters closing too late and/or opening too early cause Cross-Talk Closing these shutters too quickly and/or opening too slowly will cause Color Artifacts. R5905303 HDQ 2K40 02/03/2015...
Page 227
1. Press Menu to activate the menus and select Alignment → 3D Glasses . Image 13-159 Main window Image 13-160 Alignment, 3D glasses 2. Press ENTER. 3. Use the ▲ or ▼ key to select Dark Time Adjustment R5905303 HDQ 2K40 02/03/2015...
Right Delay Time With output reference delay Left 3D Sync Right Image 13-162 3D Output reference delay How to set the delay 1. Press Menu to activate the menus and select Alignment → 3D Glasses . R5905303 HDQ 2K40 02/03/2015...
The incoming 3D sync signal can routed to the 3D sync output connector. How to activate 1. Press Menu to activate the menus and select Alignment → 3D Glasses. Image 13-166 Main window Image 13-167 Alignment, 3D glasses R5905303 HDQ 2K40 02/03/2015...
Almost any image can be displayed on almost any place in the room using the pan and tilt adjustments. Settings storing per layout is possible. Projector control activation 1. Press Menu to activate the menus and select Alignment → High End Systems Mirror. Image 13-169 Main menu, alignment Image 13-170 Alignment, High End Systems Mirror R5905303 HDQ 2K40 02/03/2015...
Page 231
4. Use the ◄ or ► key to change the value between -128 and 128. Store settings 1. To change the store settings, use the ▲ or ▼ key to select Store settings per layout and press ENTER to toggle between [No] and [Yes]. Image 13-173 R5905303 HDQ 2K40 02/03/2015...
Page 232
13. Alignment [No] : settings are stored globally. [Yes] : settings are stored per layout. R5905303 HDQ 2K40 02/03/2015...
DHCP [On] [Off] IP address Subnet mask Default gateway Wireless Status DHCP IP address Subnet mask IR Control IR front IR back IR side Address Universe Mode Art DMX [On/Off] Output voltage enable Output voltage level Monitor Shutdown R5905303 HDQ 2K40 02/03/2015...
1. Press Menu to activate the menus and select Projector Control → Projector Address → Projector Address. Image 14-1 Main menu, projector control Image 14-2 Projector control, projector address Image 14-3 Projector address 2. Press ENTER to activate the address input. R5905303 HDQ 2K40 02/03/2015...
1. Press Menu to activate the menus and select Projector Control → Projector Address → Common Address. Image 14-5 Main menu, projector control Image 14-6 Projector control, projector address Image 14-7 Projector address, common address 2. Press ENTER to activate the address input. Image 14-8 Projector common address R5905303 HDQ 2K40 02/03/2015...
The communication protocol for the communication between the projector and a computer can be set to RS232 or RS422. How to set up 1. Press Menu to activate the menus and select Projector Control → Serial Communication. R5905303 HDQ 2K40 02/03/2015...
IP address must be entered. DHCP lets a network administrator supervise and distribute IP addresses from a central point and automatically sends a new IP address when a computer is plugged into a different place in the network. R5905303 HDQ 2K40 02/03/2015...
field to any IP-Address on the subnet. 14.5.2 Wired DHCP set up How to set up 1. Press Menu to activate the menus and select Projector Control → Network. Image 14-15 Main menu, projector control Image 14-16 Projector control, network R5905303 HDQ 2K40 02/03/2015...
[Off] : DHCP is deactivated. A fixed address must be used. 14.5.3 Wired IP address set up How to set up 1. Press Menu to activate the menus and select Projector Control → Network. Image 14-18 Main menu, projector control Image 14-19 Projector control, network R5905303 HDQ 2K40 02/03/2015...
14.5.4 Wired subnet mask set up Subnet for Wired and Wifi must be different ! How to set up 1. Press Menu to activate the menus and select Projector Control → Network. R5905303 HDQ 2K40 02/03/2015...
Page 241
Use the ◄ or ► key to select another character. Note: Digits can be entered with the digit keys on the remote control or the local keypad. When a digit is entered in that way, the next character will be selected automatically. R5905303 HDQ 2K40 02/03/2015...
Image 14-26 Main menu, projector control Image 14-27 Projector control, network Image 14-28 Network, default gateway 2. Use the ▲ or ▼ key to select Default Gateway under Wired and press ENTER to activate the input box. R5905303 HDQ 2K40 02/03/2015...
Before a wireless network can be used, the status must be set to On. How to activate 1. Press Menu to activate the menus and select Projector Control → Network → Wireless setup. Image 14-30 Main menu, projector control Image 14-31 Projector control, network R5905303 HDQ 2K40 02/03/2015...
14.5.7 Wireless access points selection and setup These menu items are only accessible when wireless network status is set to [on]. Scan for access points 1. Select Scan access points and press ENTER to start the scan. R5905303 HDQ 2K40 02/03/2015...
Page 245
Access to a wireless secured access point 1. Use the ▲ or ▼ key to select Passphrase. For a secured network, a passphrase should be entered before getting access to the wireless network. Image 14-36 Passprhrase, selection Image 14-37 Passphrase, entry R5905303 HDQ 2K40 02/03/2015...
Can only be used with a wireless network module installed. How to set up 1. Press Menu to activate the menus and select Projector Control → Network → Wireless Setup . Image 14-39 Main menu, projector control Image 14-40 Projector control, network R5905303 HDQ 2K40 02/03/2015...
Can only be used with a wireless network module installed. How to set up 1. Press Menu to activate the menus and select Projector Control → Network → Wireless Setup. Image 14-43 Main menu, projector control Image 14-44 Projector control, network R5905303 HDQ 2K40 02/03/2015...
Can only be used with a wireless network module installed. Subnet for Wired and Wifi must be different ! How to set up 1. Press Menu to activate the menus and select Projector Control → Network → Wireless Setup. R5905303 HDQ 2K40 02/03/2015...
Page 249
Image 14-50 Network, wireless Image 14-51 Network, wireless Subnet Mask 2. Press ENTER to open the Wireless menu. 3. Use the ▲ or ▼ key to select Subnet Mask and press ENTER to activate the input box. R5905303 HDQ 2K40 02/03/2015...
Can only be used with a wireless network module installed. How to set up 1. Press Menu to activate the menus and select Projector Control → Network → Wireless Setup. Image 14-53 Main menu, projector control Image 14-54 Projector control, network R5905303 HDQ 2K40 02/03/2015...
Each IR receiver inside the projector can be activated or deactivated. When an IR receiver is deactivated, no IR signal sent to this IR receiver will be processed. How to activate or deactivate 1. Press Menu to activate the menus and select Projector Control → IR control. R5905303 HDQ 2K40 02/03/2015...
DMX control. All DMX controls can be sent over the Ethernet cable. Multiple universes are possible. 14.7.1 DMX address What should be done ? Before a projector can execute DMX commands, a unique address, called DMX address, should be given to the projector. This address can vary from 1 to 512. R5905303 HDQ 2K40 02/03/2015...
Page 253
Use the ◄ or ► key to select another character. Note: Digits can be entered with the digit keys on the remote control or the local keypad. When a digit is entered in that way, the next character will be selected automatically. R5905303 HDQ 2K40 02/03/2015...
How to set a DMX universe 1. Press Menu to activate the menus and select Projector Control → DMX → Universe. Image 14-65 Main menu, projector control Image 14-66 Projector control, DMX Image 14-67 DMX, universe 2. Press ENTER to select. R5905303 HDQ 2K40 02/03/2015...
Depending on the DMX application the correct mode has to be selected. How to set the mode 1. Press Menu to activate the menus and select Projector Control → DMX → Universe. Image 14-69 Main menu, projector control Image 14-70 Projector control, DMX R5905303 HDQ 2K40 02/03/2015...
Art-Net DMX [Off] : DMX via Ethernet is disabled. How to toggle 1. Press Menu to activate the menus and select Projector Control → DMX → Art-Net DMX. Image 14-72 Main menu, projector control Image 14-73 Projector control, DMX R5905303 HDQ 2K40 02/03/2015...
DMX Art-Net, set level to 0 V How to enable or disable 1. Press Menu to activate the menus and select Projector Control → DMX → Output voltage enable. Image 14-75 Main menu, projector control Image 14-76 Projector control, DMX R5905303 HDQ 2K40 02/03/2015...
Page 258
1. Press Menu to activate the menus and select Projector Control → DMX → Output voltage level. Image 14-78 Main menu, projector control Image 14-79 Projector control, DMX Image 14-80 Front XLR output voltage level 2. Press ENTER to toggle between [0 Volt], [9 Volt], [12 Volt] and [24 Volt]. R5905303 HDQ 2K40 02/03/2015...
1. Press Menu to activate the menus and select Projector Control → DMX → Monitor. Image 14-81 Main menu, projector control Image 14-82 Projector control, DMX Image 14-83 DMX monitor 2. Press ENTER to open the overview list. R5905303 HDQ 2K40 02/03/2015...
Projector can be forced to go in shutdown after a certain retarding time when no DMX signals are available. How to activate/deactivate 1. Press Menu to activate the menus and select Projector Control → DMX → Shutdown. Image 14-85 Main menu, projector control Image 14-86 Projector control, DMX R5905303 HDQ 2K40 02/03/2015...
The retarding time is the time between no DMX is detected and the moment that the projector shuts down. How to set the retarding time 1. Press Menu to activate the menus and select Projector Control → DMX → Shutdown Time. Image 14-88 Main menu, projector control Image 14-89 Projector control, DMX R5905303 HDQ 2K40 02/03/2015...
In ECO standby only the microcontroller, communication interface and local (or remote) control are operational. All other electronics are powered down. How to set 1. Press Menu to activate the menus and select Projector Control → Buttons → Standby. Image 14-91 Main menu, projector control Image 14-92 Projector control, buttons R5905303 HDQ 2K40 02/03/2015...
Main menu, projector control Image 14-95 Projector control, buttons Image 14-96 Buttons, shortcut keys Image 14-97 Shortcut allocations 2. Use the ▲ or ▼ key to select the desired key and press ENTER to remove the allocation. R5905303 HDQ 2K40 02/03/2015...
A time out for the local LCD can be set. If there is nothing done on the local LCD, it can go out after a time out. How to set up 1. Press Menu to activate the menus and select Projector Control → Local LCD. R5905303 HDQ 2K40 02/03/2015...
French • German • Spanish • Portuguese • Japanese • Chinese • Korean • Dutch All available languages are indicated in the language of the country. The current active language is indicated by checked radio button. R5905303 HDQ 2K40 02/03/2015...
• task2: switch to layout 2 at a certain hour. No changes for the lamp. • task3: lamp off at the end of the day. Follow the next topics to create, edit or delete a task. R5905303 HDQ 2K40 02/03/2015...
2. Press ENTER to open the task creation window. The start date window is selected. Use the ▲ or ▼ key to jump to the next item in the setup. When all items are correctly filled out, select Apply and press ENTER to create the task. R5905303 HDQ 2K40 02/03/2015...
Page 268
Use the ◄ or ► key to jump to the next part of the date and time setting. Image 14-112 Time setup 3. Select Recurrence and press ENTER; Use the ◄ or ► key to change the recurrence. Image 14-113 Recurrence setup R5905303 HDQ 2K40 02/03/2015...
Use the ▲ or ▼ key to change that character. Note: Extra characters can be added at the end of the current displayed characters. Creating the task 1. Select Apply and press ENTER to create the task. R5905303 HDQ 2K40 02/03/2015...
Projector control, scheduler Image 14-118 Scheduler, edit task 2. Press ENTER to open the task selection list. Image 14-119 Task selection list 3. Use the ▲ or ▼ key to select the desired task and press ENTER R5905303 HDQ 2K40 02/03/2015...
A task stored in the list of tasks can be deleted from that list. How to delete 1. Press Menu to activate the menus and select Projector Control → Scheduler → Delete task. Image 14-121 Main menu, projector control Image 14-122 Projector control, scheduler R5905303 HDQ 2K40 02/03/2015...
When switched on, the tasks in the list will be executed on the given time. How to toggle the scheduler 1. Press Menu to activate the menus and select Projector Control → Scheduler → Scheduler [On]/[Off]. Image 14-126 Main menu, projector control Image 14-127 Projector control, scheduler R5905303 HDQ 2K40 02/03/2015...
PUK code to unblock the SIM card. How to configure 1. Press Menu to activate the menus and select Projector Control → GSM configuration → GSM pincode. R5905303 HDQ 2K40 02/03/2015...
Page 274
Image 14-134 4. Select OK and press ENTER to configure the software. Replacing a SIM card with a new one 1. Before removing the current mounted SIM card, select Projector Control → GSM configuration → GSM pincode R5905303 HDQ 2K40 02/03/2015...
When subscripted for notifications, the projector will send out SMS messages when notifications occur with severity “Critical”, “Error” or “Warning”. How to subscribe via the OSD menu 1. Press Menu to activate the menus and select Projector Control → GSM configuration → Sms subscriptions. R5905303 HDQ 2K40 02/03/2015...
Page 276
This procedure can be repeated for subscriber 2 and 3. 5. Select OK and press ENTER to configure the subscription. How to unsubscribe via the OSD menu 1. Press Menu to activate the menus and select Projector Control → GSM configuration → Sms subscriptions. R5905303 HDQ 2K40 02/03/2015...
Via Projector Toolset when connected via an Ethernet connection with the projector. See Projector Toolset’s user guide (R5905073, index 04), chapter “FLEX, light output control”. • Via the OSD menu of the projector itself • Via an SMS message send to a projector equipped with an optional GSM board. R5905303 HDQ 2K40 02/03/2015...
Image 14-150 Successful configured If the code is incorrect, the message: “Invalid attempt!”, is displayed: Image 14-151 Invalid attempt After 3 invalid attempts, the message: “Invalid attempt! Try again after 300 seconds” is displayed. Image 14-152 R5905303 HDQ 2K40 02/03/2015...
Activation code can be generated with Projector Toolset. See Projector Toolset’s user guide, chapter “Communication”, “Mobile settings”. 2. Send this message to the GSM number associated with the projector. The receiving projector analyses the message and creates a return SMS. This message is sent back to the requested cell phone. R5905303 HDQ 2K40 02/03/2015...
The receiving projector analyses the message and execute the command. It creates a return SMS with the following message: “Lamp ignition enable” or “Lamp ignition disabled” or “Lamp ignition admission failed”. This message is sent back to the requested cell phone. R5905303 HDQ 2K40 02/03/2015...
Load custom settings Reset Formatter Refill Mode Save Custom Settings Special HD Camera Mode Auto Dimming when Overtemperature Time and Date 15.2 Identification What can be seen? The identification screen shows the general information about the projector. R5905303 HDQ 2K40 02/03/2015...
Page 282
1. Press Menu to activate the menus and select Service → Identification. Image 15-1 Main menu, service Image 15-2 Service, identification Image 15-3 Identification 2. Use the ▲ or ▼ key to scroll through the menu. R5905303 HDQ 2K40 02/03/2015...
< the current has a lower version than the reference software. How to display an overview 1. Press Menu to activate the menus and select Service → Diagnosis → Versions. Image 15-4 Main menu, service Image 15-5 Service, diagnosis R5905303 HDQ 2K40 02/03/2015...
Once one of these values are crossed the threshold an error or warning message is logged or displayed on the local LCD screen. How to display an overview 1. Press Menu to activate the menus and select Service → Diagnosis → Measurements. R5905303 HDQ 2K40 02/03/2015...
Page 285
2. Use the ▲ or ▼ key to select Voltages and get an overview of the voltages or to select Temperatures to get an overview of the internal temperatures or to select Fan Speeds to get an overview of current speeds of the different fans or to get an overview of miscellaneous items such as pressure altitude etc. Image 15-12 Overview voltages R5905303 HDQ 2K40 02/03/2015...
Projector hosts two log files: one managed bythe Main controller and one specific for the Lamp power supply. How to display the logging 1. Press Menu to activate the menus and select Service → Diagnosis → Logging. R5905303 HDQ 2K40 02/03/2015...
Page 287
2. Use the ▲ or ▼ key to select Main Controller to get a logging of the main controller or to select Lamp Power Supply to get a logging of the lamp power supply. Image 15-20 Main controller logging R5905303 HDQ 2K40 02/03/2015...
1. Press Menu to activate the menus and select Service → Diagnosis → Board Id. Image 15-22 Main menu, service Image 15-23 Service, diagnosis Image 15-24 Diagnosis, board ID 2. Press ENTER to display an overview of the board IDs. R5905303 HDQ 2K40 02/03/2015...
How to display 1. Press Menu to activate the menus and select Service → Diagnosis → Notifications. Image 15-26 Main menu, service Image 15-27 Service, diagnosis Image 15-28 Diagnosis, notifications 2. Press ENTER to display the notification list. R5905303 HDQ 2K40 02/03/2015...
1. Press Menu to activate the menus and select Service → Diagnosis → Tilt sensor. Image 15-30 Main menu, service Image 15-31 Service, diagnosis Image 15-32 Diagnosis, tilt sensor 2. Press ENTER to read out the tilt sensor. R5905303 HDQ 2K40 02/03/2015...
15.4 Internal Service Patterns How to select 1. Press Menu to activate the menus and select Service → Internal Service Patterns. Image 15-34 Main menu, service Image 15-35 Service, Internal service patterns Image 15-36 Internal service patterns, Pmp In R5905303 HDQ 2K40 02/03/2015...
Page 292
To change the options for the selected pattern, use he ► key to open these options. The number of options can change for the different patterns. Image 15-40 Pmp In test pattern options Use the ▲ or ▼ key to select an option and press ENTER to select. The checkbox in front of that item will be checked. R5905303 HDQ 2K40 02/03/2015...
Page 293
Internal service patterns, OSD Press ENTER to display the list of possible patterns. Image 15-42 OSD Test patterns Pmp out patterns Image 15-43 Internal service patterns, Pmp Out Press ENTER to display the list of possible patterns. R5905303 HDQ 2K40 02/03/2015...
Page 294
To change the options for the selected pattern, use he ► key to open these options. The number of options can change for the different patterns. Image 15-45 Pmp out internal service test patterns options Fib patterns Image 15-46 Internal service patterns, Fib Press ENTER to display the list of possible patterns. Image 15-47 Fib test patterns R5905303 HDQ 2K40 02/03/2015...
2. If you want to restore also one of the items in the list, check the check box in front of that item. Select Yes to restore the factory settings. Select No to stop the restore process. R5905303 HDQ 2K40 02/03/2015...
When no USB stick is available, a message will be shown: No USB device is found. The name of the custom settings files contains the serial number of the projector from which ti is downloaded. Load custom settings 1. Press Menu to activate the menus and select Service → USB Memory. R5905303 HDQ 2K40 02/03/2015...
A reset formatter is necessary when e.g. a color is missing, artifacts are visible in the image or image is frozen and the formatter test patterns cannot be displayed. How to reset 1. Press Menu to activate the menus and select Service → Reset Formatter. R5905303 HDQ 2K40 02/03/2015...
When all necessary preparations are taken, the refill mode activates automatically the refill process. For more information about the refill process, consult the Service manual. How to start the refill mode 1. Press Menu to activate the menus and select Service → Refill Mode. R5905303 HDQ 2K40 02/03/2015...
When settings are changed when the lamp is off, a manual Save custom settings must be executed to save the changes. When the message Saving data is displayed, never switch off the projector. How to save 1. Press Menu to activate the menus and select Service → Save Custom Settings. R5905303 HDQ 2K40 02/03/2015...
When an over-temperature is detected, the projector starts dimming the lamp so that the projector can cool down. How to activate - deactivate 1. Press Menu to activate the menus and select Service → Auto Dimming when Overtemperature. Image 15-67 Main menu, service Image 15-68 Service, auto dimming when over-temperature R5905303 HDQ 2K40 02/03/2015...
Note: Digits can be entered with the digit keys on the remote control or the local keypad. When a digit is entered in that way, the next character will be selected automatically. 4. Press ENTER to accept the changes. Repeat for other values in the same way. R5905303 HDQ 2K40 02/03/2015...
Page 302
15. Service R5905303 HDQ 2K40 02/03/2015...
5. Position the filter with the up-sign (2) upwards and slide it in until it clicks into position. Image 16-1 Cleaning the front dust filter 6. Install the input cover. See "Removal of the input cover", page 308. R5905303 HDQ 2K40 02/03/2015...
Necessary tools • Compressed air. • Clean Toraysee® cloth or any micro fiber lens cleaning cloth. • Clean cotton cloth. Necessary parts Lens cleaner (e.g. Carl Zeiss lens cleaner or Purasol® or any water-based lens cleaner) R5905303 HDQ 2K40 02/03/2015...
1. Remove the left projector cover. See "Removal of the left cover", page 312. 2. Check the cooling liquid level in the reservoir. 5. Pressurized air cans are not efficient if there is too much dust on the surface, the pressure is too low R5905303 HDQ 2K40 02/03/2015...
(approximately 25 °C). The projector should have sufficiently cooled down (minimum 2 hours). ARNING Only use Barco approved cooling liquid to refill the liquid cooling circuit of the projector. Neglect- ing this may lead to irreversible damage of the projector.
The procedure below may only be performed by “qualified service technicians”. ARNING Before removing the Lamp House, disconnect the power to the projector mains terminals and unplug the power cord at the UPS INLET for removal of all power from the projector. R5905303 HDQ 2K40 02/03/2015...
How to realign the lamp in its reflector ? 1. Remove the lamp cover. See "Removal of the lamp cover", page 307. 2. Start up the projector, enter the menu structure and select Lamp → Z-axis. 3. Loosen the Z-axis lock screw (2). R5905303 HDQ 2K40 02/03/2015...
3. Initiate authorization by holding the security key in the security socket D.. Image 16-7 Keypad The color of the backlight of the numeric keys 1 to 6 of the local keypad changes from blue to yellow. 4. Enter pin code within 5 seconds. R5905303 HDQ 2K40 02/03/2015...
Page 310
In case of a correct code entry, the color of the backlight of the numeric keys 1 to 10 changes to green for 1 second and then back to blue. Each attempt to clear the security warning and its result (successfully or unsuccessfully) is logged inside the projector. R5905303 HDQ 2K40 02/03/2015...
How to remove the lamp cover? 1. Release the 2 captive screws (1). 2. Release the 2 locks by sliding them towards each other (2). Pull the bottom side away from the projector. 3. Remove the cover (3). R5905303 HDQ 2K40 02/03/2015...
2. Slide the locks to each other (2) and push the cover against the projector. Release the locks. 3. Tighten the 2 captive screws (3). Image 17-3 Installing the lamp cover 17.3 Removal of the input cover Necessary tools Flat screwdriver R5905303 HDQ 2K40 02/03/2015...
1. Position the input cover on its place and slide it towards the projector (1). 2. Push the cover against the projector until the locks at the bottom snap. 3. Tighten the 2 captive screws (2). Image 17-5 Installing the input cover R5905303 HDQ 2K40 02/03/2015...
Image 17-7 Removing the front cover 17.6 Installation of the front cover Necessary tools Flat screwdriver How to install the front cover? 1. Position the front cover on its place and slide it towards the projector (1). R5905303 HDQ 2K40 02/03/2015...
17.7 Removal of the back cover Necessary tools Flat screwdriver How to remove the back cover? 1. Release the 2 captive screws (1). 2. Pull back the cover until the locking mechanism at the top releases. 3. Remove the cover (2). R5905303 HDQ 2K40 02/03/2015...
2. Push the cover against the projector until the locks at the top snap. 3. Tighten the 2 captive screws (2). Image 17-11 Installing the back cover 17.9 Removal of the left cover Necessary tools Flat screwdriver R5905303 HDQ 2K40 02/03/2015...
(3). 2. Slide the locks to each other (4) and push the cover against the projector. Release the locks. 3. Tighten the 2 captive screws (5). Image 17-13 Installing the left cover R5905303 HDQ 2K40 02/03/2015...
Page 318
17. Removal and installation of the projector covers R5905303 HDQ 2K40 02/03/2015...
About this chapter This chapter gives you an overview of all the relevant specifications of the Barco HDQ 2K40. All the dimensions which could be necessary when using the projector in a specific setup or configuration are given on the drawings. Also the lens-to-lens distance, applicable when the projector is used in a stacking configuration, is given.
15 Class A and CE EN55022 Class A, RoHS Warranty 2 years standard, extendable up to 5 years A.3 Technical Regulations Certificates RoHS Image A-3 Image A-4 Image A-5 Image A-2 Rohs Rohs OK CE mark EAC mark R5905303 HDQ 2K40 02/03/2015...
Page 322
A. Specifications R5905303 HDQ 2K40 02/03/2015...
9. Fpix MHz: pixel frequency 10. Ptot : total pixels on one horizontal line. 11. Pact: active pixels on one horizontal line. 12. Ltot: total lines in one field 13. Lact: active lines in one field. R5905303 HDQ 2K40 02/03/2015...
Mechanical shutter closed 6 - 255 Electronic contrast on output Brightness 0 - 255 Adjusts the brightness between 0 and 100% on input 0 - 255 Contrast Adjust the contrast between 0 and 100% on input R5905303 HDQ 2K40 02/03/2015...
0 - 5 6 - 255 Electronic contrast on output Brightness 0 - 255 Adjusts the brightness between 0 and 100% on input Contrast 0 - 255 Adjusts the contrast between 0 and 100% on input R5905303 HDQ 2K40 02/03/2015...
Page 329
Stand by / Lamp Off (if held for 5 seconds) 224 - 231 XLR output voltage On (if held for 5 seconds) 232 - 239 XLR output voltage Off (if held for 5 seconds) 240 - 255 No function 14. Only when lens is calibrated R5905303 HDQ 2K40 02/03/2015...
Page 330
C. DMX chart R5905303 HDQ 2K40 02/03/2015...
For more information about recycling of this product, please contact your local city office or your municipal waste disposal service. For details, please visit the Barco website at: http://www.barco.com/en/AboutBarco/weee...
Page 332
SJ/T11363-2006. X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求. X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ/T11363-2006 R5905303 HDQ 2K40 02/03/2015...
The month and year of production is indicated on the product ID label on the product itself. D.4 Importers contact information Contact To find your local importer, contact Barco directly or one of Barco’s regional offices via the contact information given on Barco’s web site, www.barco.com. R5905303 HDQ 2K40 02/03/2015...
Page 334
D. Environmental information R5905303 HDQ 2K40 02/03/2015...
Cleaning the exterior of the projector stacked clean Alignment 173–180, 202, 204–206, 208–212, 214, 217, 220–221 exterior CLO mode Dark time CLO targets 3D Glasses Color space Blanking Color temperature 121–123 Color space Custom values R5905303 HDQ 2K40 02/03/2015...
Page 336
15, 21 Art-Net Download plug-in DMX address Download Projector Toolset DMX universe 250–251 General considerations Front XLR output voltage Getting started 65, 71–72 Monitor Projector address Shutdown Source selection Shutdown retarding time Terminology overview DMX chart 323–324 R5905303 HDQ 2K40 02/03/2015...
Page 337
Files Auto dimming when over-temperature Manual load file CLO mode Option auto picture alignment CLO targets Option load file Identification Rename LPS power Important safety instructions Overview Importer Power Information Power mode Request via SMS Realign R5905303 HDQ 2K40 02/03/2015...
Page 338
Bar scale Light output configuration, OSD Menu FLEX power connection Light output control connection Set light output power Via SMS Power mode Load Lamp Image file power net Manual Production Local keypad Projector address 71–72, 230–231 R5905303 HDQ 2K40 02/03/2015...
Page 339
Interface standard LENS key Service 277, 279–280, 282, 284–287, 291–297 Auto dimming Text on/off Over-temperature Date Set up Diagnosis 279–280, 282, 284–286 Board Id 23–26, 65, 71 Logging Address Measurements How to use Notification Possibilities Tilt sensor R5905303 HDQ 2K40 02/03/2015...
Page 340
Save as Switch off Wired remote control Switch on Switching off Switching on Switching to standby Y-Δ (wye-delta) configuration Δ delta Technical Regulations Test patterns Adjustment mode Text on/off Tilt sensor Projector position Z-axis, current light output R5905303 HDQ 2K40 02/03/2015...
Page 341
Revision Sheet Barco nv/Documentation Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.82.11, Fax: +32 56.36.88.24 Support: www.Barco.com/esupport, Web: www.barco.com From: Date: Please correct the following points in this documentation (R5905303/09): page wrong correct R5905303 HDQ 2K40 02/03/2015...
Need help?
Do you have a question about the HDQ 2K40 and is the answer not in the manual?
Questions and answers