Page 1
HDQ 4K35 User and Installation manual R5905823/04 30/11/2015...
Page 2
Barco NV President Kennedypark 35, 8500 Kortrijk, Belgium Phone: +32 56.36.82.11 Fax: +32 56.36.883.86 Support: www.barco.com/en/support Visit us at the web: www.barco.com Printed in Belgium...
Page 3
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacement at its own discretion within an appropriate period.
Read this chapter attentively. It contains important information to prevent personal injury while installing and using a Barco HDQ 4K35. Furthermore, it includes several cautions to prevent damage to the HDQ 4K35. Ensure that you understand and follow all safety guidelines, safety instructions and warnings mentioned in this chapter before installing your HDQ 4K35. After this chapter, additional “warnings”...
SONNEL, AUTHORIZED to operate professional projection systems. A Barco HDQ 4K35 is intended "FOR PROFESSIONAL USE ONLY" by AUTHORIZED PERSONNEL familiar with potential hazards associated with high voltage, high intensity light beams, ultraviolet exposure and high temperatures generated by the lamp and associated circuits.
Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, remove all power from the projector. This will prevent damage to the projector due to lightning and AC power-line surges. R5905823 HDQ 4K35 30/11/2015...
Page 10
ARNING The complete exhaust box is very hot when the projector is on. To avoid burns, let the projector cool down for at least 15 minutes before touching the exhaust box. R5905823 HDQ 4K35 30/11/2015...
Page 11
In the event of fire, use sand, CO electrical fire. Always have service performed on this projector by authorized Barco service personnel. Always insist on genuine Barco replacement parts. Never use non-Barco replacement parts as they may degrade the safety of this projector.
Page 12
If the product exhibits a distinct change in performance, indicating a need for service. • Replacement parts: When replacement parts are required, be sure the service technician has used original Barco replacement parts or authorized replacement parts which have the same characteristics as the Barco original part. Unauthorized substitu- tions may result in degraded performance and reliability, fire, electric shock or other hazards.
Read this chapter before installing your Barco HDQ 4K35. It contains important information concerning installation requirements for the HDQ 4K35, such as minimum and maximum allowed ambient temperature, humidity conditions, required safety area around the installed projector, required power net, etc.
The HDQ 4K35 operates from a nominal 230/400V 3W+N+PE 16A 50-60Hz or 208V 3W+PE 27A 50-60Hz. The projector must be switched internally between a star connection to a delta connection or vice versa. See "Power input setup of the HDQ 4K35", page For a 3W+N+PE system, 400V is measured between the lines, 230V is measured between the lines and the neutral.
2. Unfold the top side of the outer cardboard box. Take out the small box located between inner and outer cardboard box (this box contains the accessories such as manuals, remote control, etc.). Remove the outer cardboard box by sliding it up above the projector. R5905823 HDQ 4K35 30/11/2015...
Page 16
Release the projector from the supporting wooden board by removing the 4 screws. Warning: It is forbidden to lift up the projector with manpower, use a hoisting tool instead. Do not underestimate the weight of the projector. The projector weights ±210 kg (±462 lb.). R5905823 HDQ 4K35 30/11/2015...
Page 17
A rubber foam inside a plastic bag is placed into the lens opening of the projector. It’s recommended to reuse this foam and plastic back each time you transport the projector. This to prevent intrusion of dust and foreign particles. The lens is delivered in a separate box. R5905823 HDQ 4K35 30/11/2015...
This check should confirm that there are no broken knobs or connectors, that the cabinet and panel surfaces are free of dents and scratches, and that the operating panel is not scratched or cracked. The Barco Sales and Service office should be notified as soon as possible if this is not the case.
Air inlets and outlets Air inlets and outlets Image 2-6 The HDQ 4K35 projector has 3 air inlets (1 at the front and 2 at the bottom) and 2 air outlets (on the exhaust box on top of the projector). ARNING When the projector is used in portrait mode, the air outlet is positioned towards the floor.
After you have unpacked and checked the projector you can start with the installation process of your Barco HDQ 4K35. This chapter gives you an overview of all the different stages in the installation process which you have to follow to set your HDQ 4K35 up and running.
Overview • Installation of the Lamp House • Access to the power connection • Power input setup of the HDQ 4K35 • Connecting the projector with the power net • Connecting a UPS to the projector electronics • Landscape and portrait mode •...
5. Secure the Lamp House by fastening the two retaining screws (1) at the base of the Lamp House. Use a 10 mm nut driver or a flat screwdriver. Image 3-2 Installation of the Lamp House 6. Install the lamp cover. R5905823 HDQ 4K35 30/11/2015...
1. Remove the back cover of the projector. See "Removal of the back cover", page 88. 2. Release the 2 captive screws (1). 3. Remove the power connection cover (2). Image 3-3 Power connection access The terminal barrier strip (3) and Y-Δ configuration block (4) is accessible. R5905823 HDQ 4K35 30/11/2015...
3. Physical installation Power input setup of the HDQ 4K35 About the power input The projector power input can be configured for a power supply of 230/400V 3W+N+PE (Υ-connection) or for 208V 3W+PE (Δ-con- nection). Before operating the projector, place the links in the correct position depending on the local power supply.
Page 25
2. Take off the mounted links (A, B and C). 3. Connect the right pins together. Place 2 links between the upper pin and the middle pin (A, B)and 1 link between the middle pin and the lower pin (C). R5905823 HDQ 4K35 30/11/2015...
Always connect ground conductor (PE) first. Note: Always connect the neutral conductor (N) when available. Image 3-7 Power connection 7. Install the power connection cover. 8. Install the back cover of the projector. See "Removal of the back cover", page 88. R5905823 HDQ 4K35 30/11/2015...
UPS. A short power link cable (with plug type C13/C14) loops the power through to the projector electronics. ARNING Only use UPS units which are suitable for the HDQ 4K35. How to connect a UPS to the projector electronics? 1.
Page 28
The electrical connection with the UPS INLET socket of the projector must be done with a certified AC power supply cord (minimum 0,75 mm² or 18 AWG and minimum 300V) AUTION Do not use the power OUTLET socket of the projector to provide power to other equipment! R5905823 HDQ 4K35 30/11/2015...
The projector can be used in landscape or portrait mode. The illustrations below shows which positions are allowed and which are not. Image 3-11 Landscape mode (allowed) Portrait mode (allowed) Upside down (disallowed) Turned over portrait mode (disallowed) Upwards (disallowed) Downwards (disallowed) R5905823 HDQ 4K35 30/11/2015...
Page 30
It is not allowed to stack multiple projectors in portrait mode. AUTION When the projector is used in portrait mode, always ensure the cooling liquid level is sufficient. To check the cooling liquid level, see "Checking cooling liquid level", page 74. R5905823 HDQ 4K35 30/11/2015...
Introduction The Barco HDQ 4K35 is mounted by default in a multifunctional frame. This frame can be used to stack multiple projectors onto each other. The stacked projectors can be used in a standing (table mount) or hanging configuration (ceiling mount).
Page 32
The projector weights ±210 kg (±462 lb.). 4. Slide in the 4 pipe lynch pins (3) and secure them by swinging the lever (4). Image 3-14 Stacking projectors 5. Mount 2 (two) safety cables to secure both projector frames to each other: R5905823 HDQ 4K35 30/11/2015...
Page 33
Make sure that the falling distance is maximum 20 cm (8”). If necessary, before clasping the safety hook around the cable, turn the cable a few time around the frame. c) Repeat this procedure for the other safety cable on the other side of the frame. 2x 2x Image 3-15 R5905823 HDQ 4K35 30/11/2015...
3. Physical installation Adjusting the multifunctional frame Introduction The Barco HDQ 4K35 is mounted by default in a multifunctional frame. This frame can be used to adjust the projector position. The frame can be adjusted in 3 different ways: •...
Page 35
2. Turn the adjustment rod (2) clockwise to skew the projector clockwise anti clockwise to skew the projector anti clockwise. 3. Tighten the locking screw(s) (1). Use a 2.5 mm Allen wrench. Tip: Only secure the most reachable locking screw(s). Image 3-18 Skewing the projector R5905823 HDQ 4K35 30/11/2015...
Use Communicator software to shift. In the navigation pane, click on Configuration → Lens. The Lens settings menu opens. Use the Lens shift buttons to shift the image. Or, use the shift buttons on the local keypad. R5905823 HDQ 4K35 30/11/2015...
Page 37
8. Focus the projector to the screen until the hatch pattern is perfectly sharp. Use Communicator software to focus. In the navigation pane, click on Configuration → Lens. The Lens settings menu opens. Use the Lens focus buttons to focus the image. R5905823 HDQ 4K35 30/11/2015...
Adjust until the outline of the hatch pattern is most symmetric with the reference hatch pattern. Inclination Image 3-25 6. Adjust the skew of the stacked projector with respect to the reference projector. Adjust until the outline of the hatch pattern is most symmetric with the reference hatch pattern. R5905823 HDQ 4K35 30/11/2015...
Page 39
Use Communicator software to zoom. In the navigation pane, click on Configuration → Lens. The Lens settings menu opens. Use the Lens zoom buttons to zoom the image. Or, use the zoom buttons on the local keypad. Zoom Image 3-28 R5905823 HDQ 4K35 30/11/2015...
Page 40
Use the Lens focus buttons to focus the image. In case of a triple stacked standing projector configuration (table mount) adjust and align the reference pro- jector first, than the middle projector and finally the uppermost projector. R5905823 HDQ 4K35 30/11/2015...
About this chapter This chapter gives an overview of available lenses for the Barco HDQ 4K35 and explains how you can select the best suited lens for your specific situation using the lens formulas. Also, it is explained how to install and remove a lens from the projector lens holder.
4. Lenses & Lens Holder Available lenses Which lenses are available for my projector? The table below is subject to changes. Consult Barco’s web site and click on myBarco for the most recent information about available lenses. Product Number Zoom range...
How to select the right lens 1. Determine the required screen width (SW). 2. Determine the approximate position of the projector in the room. 3. Start up the Lens Calculator on the Barco website: http://www.barco.com/en/tools/lenscalculator to determine the possible lenses for your configuration.
2. Take the lens assembly out of its packing material and remove the lens caps on both sides. 3. Place the lens holder in the “unlocked” position by moving the lens lock handle (1) towards the lens power supply socket (2). Image 4-12 Unlock lens holder R5905823 HDQ 4K35 30/11/2015...
Page 46
8. Continue with the installation of the lens fixation mechanism, see "Installing the lens fixation mechanism", page 44. AUTION Never transport the projector with a Lens mounted in the Lens Holder. Always remove the Lens before transporting the projector. Neglecting this can damage the Lens Holder and Prism. R5905823 HDQ 4K35 30/11/2015...
It’s recommended to place the foam rubber of the original projector packaging, back into the Lens opening to prevent intrusion of dust. Note that this foam rubber is packed in a plastic bag to prevent the dust, emitted by the foam, from entering the projector. R5905823 HDQ 4K35 30/11/2015...
Depending on which lens is used, it may not always be possible to install the fixation brackets at the positions showed on the illustration. In that case, the brackets may be installed on the underside of the lens, following the same principle. Always install 2 fixation brackets. R5905823 HDQ 4K35 30/11/2015...
How to remove the lens fixation mechanism? 1. Remove the nuts (2) from the fixation brackets. Use a 10 mm wrench. 2. Remove the fixation brackets (1) from the Lens Holder. Image 4-18 Removing the lens fixation mechanism R5905823 HDQ 4K35 30/11/2015...
Take into account that the lens focus may slightly drift while the lens is warming up from cold to operation temperature. This is a typical phenomenon for projection lenses used with high brightness projectors. The operation temperature of the lens is reached after approximately 30 minutes projection of average video. R5905823 HDQ 4K35 30/11/2015...
Introduction The lens of the HDQ 4K35 can be shifted vertically. The maximum vertical shift range is ±110% in both directions, which is not sufficient in some situations. To extend the vertical shift range in a certain direction, the Lens Holder can be shifted manually.
1, 2 and 3 Scheimpflug adjustment nuts A, B, C and D Set screws a, b, c and d lock nuts 1, 2 and 3 are adjustment points. 4 is a locking point and NOT used during Scheimpflug adjustment. R5905823 HDQ 4K35 30/11/2015...
Turn the Scheimpflug adjustment nuts 1, 2 and 3 until the front of the nut is equally aligned with the front of the threaded rod. b) Adjust the focus in the center of the screen (F) using the motorized focus control. Image 4-26 Center focusing 6. Sharpen bottom left corner of the screen by adjusting nut 1. R5905823 HDQ 4K35 30/11/2015...
Page 54
4. Lenses & Lens Holder Image 4-27 Left bottom focusing 7. Sharpen bottom right corner of the screen by adjusting nut 2. Image 4-28 Right bottom focusing 8. Sharpen top right corner of the screen by adjusting nut 3 R5905823 HDQ 4K35 30/11/2015...
Page 55
9. Repeat from step 6 until the projected focus pattern is as sharp as possible in the center, left, right, top and bottom of the screen. 10.Continue with the Fixation of the lens holder front plate procedure. R5905823 HDQ 4K35 30/11/2015...
Note: Ensure that the edges of the projected test pattern remain in place on the screen. Any movement of the image will affect the Scheimpflug adjustment. Tip: Fasten the set screw and the Scheimpflug nut alternately, without disturbing the projected image, until the Scheimpflug nut and set screw are completely tightened. R5905823 HDQ 4K35 30/11/2015...
Page 57
4. Lenses & Lens Holder Image 4-32 7. Fasten the lock nut at the lower left of the Lens Holder. Use a 10mm nut driver. R5905823 HDQ 4K35 30/11/2015...
5. INPUT AND COMMUNICATION Overview • Introduction • Local keypad of the HDQ projector • Communication ports of the HDQ projector • Source input ports of the Barco HDQ 4K35 projector • ICMP status LEDs • ICMP reset R5905823 HDQ 4K35 30/11/2015...
Communication ports Socket for security key Fan controller module Display ports HDMI port 3G-SDI ports AUTION A unit may only be removed by qualified service personnel. Removing a unit will result in an authorization request upon starting. R5905823 HDQ 4K35 30/11/2015...
The shift keys (6) allow you to shift the lens up/down or left/right. Focus keys The focus keys (7) allow you to focus the projected image on the screen. Zoom keys The zoom keys (8) allow you to zoom in or out the projected image on the screen. R5905823 HDQ 4K35 30/11/2015...
Communicator touch panel. See user’s guide of the Touch panel, section Macro editor, for more informa- tion about this functionality. Note that the General Purpose Inputs accept 24 volt maximum. 3D INTERFACE Optional port. R5905823 HDQ 4K35 30/11/2015...
Page 63
5. Input and Communication Can be used to connect external 3D devices to the projector. All signals necessary for 3D projection can be provided via this con- nector. PERIPHERAL PORT For future use. R5905823 HDQ 4K35 30/11/2015...
5. Input and Communication Source input ports of the Barco HDQ 4K35 projector Location of the source input ports RS232 IN 3D INTERFACE PERIPHERAL PORT 10 / 100 / 1000 BASE-T DVI INPUT GENERAL PURPOSE IN/OUT DVI A DVI B...
Page 65
A+B span @48Hz 2048 x 2160 8, 10 A+B span @50Hz 2048 x 1080 8, 10 Single up scale @60Hz 2048 x 1080 8, 10 Single up scale @48Hz 3840 x 2160 8, 10 Single left/right @24Hz R5905823 HDQ 4K35 30/11/2015...
Page 66
All input resolutions are scaled towards the desired resolution specified in the screen presentation file. Audio formats • LPCM 8-channel (7.1), 16/20/24-bit at 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz. Additional features • YCbCr 4:4:4 • YCbCr 4:2:2 • Deep Color : 30bpp, 36bpp R5905823 HDQ 4K35 30/11/2015...
Security Manager - Self Test Blinking Green Yellow Security Manager - FPGA self-test Green Blinking Orange Update ongoing Green Blinking Green FIPS ok - Application startup Green Green Power on & No Error Blinking Red FIPS error R5905823 HDQ 4K35 30/11/2015...
As a result the projector is safely prepared for the ICMP reboot. All ongoing events on the ICMP (e.g. ingest) are stopped immediately and the ICMP restarts. Image 5-6 ARNING Resetting the ICMP with the hardware reset button may cause damage to the content on the HDDs. A re-configuration of the whole system may be required! R5905823 HDQ 4K35 30/11/2015...
9. Press the DOWSER button on the local keypad or use the Communicator Touch Panel to open the dowser. As a result the applied source will be displayed. AUTION See user’s guide of the Communicator Touch Panel to operate and control the HDQ. R5905823 HDQ 4K35 30/11/2015...
As a result the lamp turns off but the fans remain turning to cool down the projector. 2. Let the projector cool down at least 5 minutes or until the speed of the fans decreases. 3. Switch OFF the projector with the power switch. R5905823 HDQ 4K35 30/11/2015...
Cleaning the exterior of the projector • Checking cooling liquid level • Topping up the cooling liquid reservoir • Removal of the Lamp House • Realignment of the lamp in its reflector • Authorization to clear security warning on the projector R5905823 HDQ 4K35 30/11/2015...
5. Position the filter with the up-sign (2) upwards and slide it in until it clicks into position. Image 7-1 Cleaning the front dust filter 6. Install the input cover. See "Removal of the input cover", page 84. R5905823 HDQ 4K35 30/11/2015...
5. Position the filters with the flanges upwards (3) and slide them in until they click into position. Image 7-2 Cleaning the bottom dust filters 6. Install the left cover. See "Removal of the left cover", page 90. R5905823 HDQ 4K35 30/11/2015...
If smears occur when cleaning lenses, replace the cloth. Smears are the first indication of a dirty cloth. 1. Pressurized air cans are not efficient if there is too much dust on the surface, the pressure is too low R5905823 HDQ 4K35 30/11/2015...
1. Disconnect the power to the projector mains terminals and unplug the power cord at UPS INLET for removal of all power from the projector. 2. Clean the housing of the projector with a damp cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. R5905823 HDQ 4K35 30/11/2015...
If the current cooling liquid level is approaching the Min level point, check for leakage in the cooling system prior to starting the topping up procedure. If the cooling liquid level is not visible, open the filler cap and shine a torch into the reservoir. R5905823 HDQ 4K35 30/11/2015...
(approximately 25 °C). The projector should have sufficiently cooled down (minimum 2 hours). ARNING Only use Barco approved cooling liquid to refill the liquid cooling circuit of the projector. Neglect- ing this may lead to irreversible damage of the projector.
Page 80
Tighten the filler cap sufficiently to avoid cooling liquid leakage. Tighten to a torque of 7 Nm. 5. Install the left projector cover. See "Removal of the left cover", page 90. AUTION Never fill the cooling liquid reservoir above the Max level mark. R5905823 HDQ 4K35 30/11/2015...
Place the Lamp House on a solid and stable support. Warning: Be aware of the weight of the Lamp House. Take the necessary precautions to avoid personal injury. Image 7-5 Removal of the Lamp House R5905823 HDQ 4K35 30/11/2015...
5. Secure the Z-axis position by fastening the Z-axis lock screw (2). 6. Switch off the projector, wait five minutes and unplug the power cord at the projector side. 7. Install the lamp cover. See "Installation of the lamp cover", page 83. R5905823 HDQ 4K35 30/11/2015...
In case of a correct code entry, the color of the backlight of the numeric keys 1 to 10 changes to green for 1 second and then back to blue. Each attempt to clear the security warning and its result (successfully or unsuccessfully) is logged inside the projector. R5905823 HDQ 4K35 30/11/2015...
Location of the covers The image below shows the location of the projector covers. Each cover can be removed individually. Image 8-1 Location of the covers Lamp cover Input cover Front cover Back cover Left cover R5905823 HDQ 4K35 30/11/2015...
1. Release the 2 captive screws (1). 2. Release the 2 locks by sliding them towards each other (2). Pull the bottom side away from the projector. 3. Remove the cover (3). Image 8-2 Removing the lamp cover R5905823 HDQ 4K35 30/11/2015...
1. Position the lamp cover on its place and slide it towards the projector (1). 2. Slide the locks to each other (2) and push the cover against the projector. Release the locks. 3. Tighten the 2 captive screws (3). Image 8-3 Installing the lamp cover R5905823 HDQ 4K35 30/11/2015...
How to remove the input cover? 1. Release the 2 captive screws (1). 2. Pull back the cover until the locking mechanism at the bottom releases. 3. Remove the cover (2). Image 8-4 Removing the input cover R5905823 HDQ 4K35 30/11/2015...
1. Position the input cover on its place and slide it towards the projector (1). 2. Push the cover against the projector until the locks at the bottom snap. 3. Tighten the 2 captive screws (2). Image 8-5 Installing the input cover R5905823 HDQ 4K35 30/11/2015...
Image 8-6 Removing the rubber dust ring 2. Release the captive screw (1). 3. Pull back the cover until the locking mechanism at the top releases. 4. Remove the cover (2). Image 8-7 Removing the front cover R5905823 HDQ 4K35 30/11/2015...
2. Push the cover against the projector until the locks at the top snap. 3. Tighten the captive screw (2). Image 8-8 Installing the front cover 4. Reinstall the rubber dust ring around the Lens Holder. Image 8-9 Installing the rubber dust ring R5905823 HDQ 4K35 30/11/2015...
How to remove the back cover? 1. Release the 2 captive screws (1). 2. Pull back the cover until the locking mechanism at the top releases. 3. Remove the cover (2). Image 8-10 Removing the back cover R5905823 HDQ 4K35 30/11/2015...
1. Position the back cover on its place and slide it towards the projector (1). 2. Push the cover against the projector until the locks at the top snap. 3. Tighten the 2 captive screws (2). Image 8-11 Installing the back cover R5905823 HDQ 4K35 30/11/2015...
3. Lift the cover up a little (3) and slide it out on the front side of the frame (5) while turning the back of the cover away from the projector (4). Image 8-12 Removing the left cover R5905823 HDQ 4K35 30/11/2015...
(3). 2. Slide the locks to each other (4) and push the cover against the projector. Release the locks. 3. Tighten the 2 captive screws (5). Image 8-13 Installing the left cover R5905823 HDQ 4K35 30/11/2015...
Page 96
8. Removal and installation of the projector covers R5905823 HDQ 4K35 30/11/2015...
A. Dimensions and specifications A.1 Dimensions of the Barco HDQ 4K35 Dimensions 1248 1024 Image A-1 Dimensions of the Barco HDQ 4K35 • Lens-to-lens distance (with stacked projectors): 870 mm R5905823 HDQ 4K35 30/11/2015...
A. Dimensions and specifications A.2 Specifications of the Barco HDQ 4K35 Overview Projector type 4K 3-chip DLP digital projector Technology 1.38" DMD™ x3 Resolution 4,096 x 2,160 Brightness 35,000 center lumens / 33,000 ANSI lumens* Contrast ratio 2,000:1 (standard) Brightness uniformity...
Page 101
A. Dimensions and specifications Warranty 3 years standard, extendable up to 5 years +/- 10% R5905823 HDQ 4K35 30/11/2015...
A. Dimensions and specifications A.3 Technical Regulations Certificates RoHS Image A-3 Image A-4 Image A-5 Image A-2 Rohs Rohs OK CE mark EAC mark R5905823 HDQ 4K35 30/11/2015...
B. Environmental information B. ENVIRONMENTAL INFORMATION Overview • Disposal information • RoHS compliance • Production address • Importers contact information R5905823 HDQ 4K35 30/11/2015...
For more information about recycling of this product, please contact your local city office or your municipal waste disposal service. For details, please visit the Barco website at: http://www.barco.com/en/AboutBarco/weee...
Chinese Mainland, marked with the Environmental Friendly Use Period (EFUP) logo. The number inside the EFUP logo that Barco uses (please refer to the photo) is based on the “General guidelines of environment-friendly use period of electronic information products”...
B. Environmental information B.3 Production address Factories Barco NV Noordlaan 5, B-8520 Kuurne (BELGIUM) Barco Visual (Beijing) Electronics Co. Ltd. 巴可伟视(北京)电子有限公司 No.16 Changsheng Road, Changping District, 102200, Beijing, P.R.C 北京市昌平区中关村科技园区昌平园昌盛路16号 邮政编码:102200 Made in information The made in country is indicated on the product ID label on the product itself.
B. Environmental information B.4 Importers contact information Contact To find your local importer, contact Barco directly or one of Barco’s regional offices via the contact information given on Barco’s web site, www.barco.com. R5905823 HDQ 4K35 30/11/2015...
Page 108
B. Environmental information R5905823 HDQ 4K35 30/11/2015...
SMPTE Society of Motion Picture and Television Engineers - A global organization, based in the United States, that sets standards for baseband visual communications. This includes film as well as video standards. Uninterruptible Power Supply R5905823 HDQ 4K35 30/11/2015...