F: Option Settings - YASKAWA L1000A Technical Manual

B.3 Parameter Table
<10> The display resolution depends on the rated output power of the drive. Models CIMR-L 2A0018 to 0033 and CIMR-L 4A0009 to 0018
display values in 0.01 A units, while models CIMR-L 2A0047 to 0415 and CIMR-L 4A0024 to 0260 display values in 0.1 A units.
■
E5: PM Motor Settings
No.(Addr.) Name
E5-02
(32AH) Motor Rated Power
<1>
E5-03
(32BH) Motor Rated Current
<1>
E5-04
(32CH) Number of Motor Poles
<1>
E5-05
Motor Stator Resistance
(32DH)
(Single Phase)
<1>
E5-06
(32EH) Motor d-Axis Inductance
<1>
E5-07
(32FH) Motor q-Axis Inductance
<1>
E5-09
(331H) Motor Induction Voltage Constant 1
<1>
E5-11
Encoder Offset
(333H)
E5-24
Motor Induction Voltage Constant 2
(353H)
<1> Parameter setting value is not reset to the default value when the drive is initialized.
<4> Default setting value is determined by the drive model (o2-04).
<10> The display resolution depends on the rated output power of the drive. Models CIMR-L 2A0018 to 2A0033 and CIMR-L 4A0009 to
4A0018 display values in 0.01 A units, while models CIMR-L 2A0047 to 2A0415 and CIMR-L 4A0024 to 4A0260 display values in 0.1 A
units.

◆ F: Option Settings

F parameters are used to program the drive for Encoder and PG feedback from the motor and to function with option
cards.
■
F1: PG Speed Control Card
No.(Addr.) Name
F1-01
Encoder 1 Resolution
(380H)
F1-02 Operation Selection at PG Open
(381H) Circuit (PGo)
F1-03 Operation Selection at Overspeed
(382H) (oS)
348
V/f OLV
Sets the rated capacity of the motor.
V/f OLV
Sets the motor rated current.
V/f OLV
Sets the number of motor poles.
V/f OLV
Sets the stator resistance (1 phase value).
V/f OLV
Sets the d-axis inductance.
V/f OLV
Sets the q-axis inductance.
V/f OLV
Sets the induced phase peak voltage in units of 0.1 mV (rad/s) [electrical angle].
When setting this parameter, E5-24 should be set to 0.0.
V/f OLV
Sets the offset between the rotor magnetic axis and the encoder zero position. Set during
Encoder Offset Tuning.
V/f OLV
Sets the induced phase-to-phase rms voltage in units of 0.1 mV/(r/min) [mechanical angle].
When setting this parameter, E5-24 should be set to 0.0.
V/f OLV
Sets the encoder resolution (number of pulses per revolution)
V/f OLV
0: Ramp to stop. Decelerate to stop using the deceleration ramp in C1-02.
1: Coast to stop.
2: Fast Stop. Decelerate to stop using the deceleration ramp in C1-09.
3: Alarm only.
V/f OLV
0: Ramp to stop. Decelerate to stop using the deceleration ramp in C1-02.
1: Coast to stop.
2: Fast Stop. Decelerate to stop using the deceleration ramp in C1-09.
3: Alarm only.
YASKAWA ELECTRIC SIEP C710616 38A YASKAWA AC Drive L1000A Technical Manual
Description
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
Description
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
Setting Page
common_ Default:
<4>
TMonly
Min: 0.10 kW
Max: 650.00 kW
Default:
<4>
common_ Min: 10% of drive rated
TMonly
current
Max: 200% of drive
rated current
<10>
common_
Default: 12
TMonly
Min: 2
Max: 48
common_ Default:
<4>
TMonly Min: 0.000 Ω
Max: 65.000 Ω
common_ Default:
<4>
TMonly
Min: 0.00 mH
Max: 600.00 mH
common_ Default:
<4>
TMonly
Min: 0.00 mH
Max: 600.00 mH
common_ Default:
<4>
TMonly
Min: 0.0 mV/(rad/s)
Max:
6500.0 mV/(rad/s)
common_
Default: 0.0 deg
TMonly
Min: -180 deg
Max: 180 deg
common_ Default: 0.0 mV/(r/min)
TMonly
Min: 0.0 mV/(r/min)
Max: 6500.0 mV/
(r/min)
Setting Page
common_ Default:
<5>
TMonly
Min: 1 ppr
Max: 60000 ppr
<34>
common_
TMonly
Default: 1
Min: 0
Max: 3
common_
TMonly
Default: 1
Min: 0
Max: 3
175
175
175
175
176
176
176
176
176
177
177
177