O: Operator Related Parameters - YASKAWA L1000A Technical Manual

B.3 Parameter Table
No. (Addr.) Name
n8-84
Polarity Detection Current
(2D3H)
n8-86 Magnet Pole Search Error
(2D5H) Detection Selection
<9> Values shown here are for 200 V class drives. Double the value when using a 400 V class drive.
■
:
n9 Current Detection Adjustments
No. (Addr.) Name
n9-60
A/D Conversion Start Delay
(64DH)
<4> Default setting is determined by the drive model (o2-04).

◆ o: Operator Related Parameters

The o parameters set up the digital operator displays.
■
o1: Digital Operator Display Selection
No. (Addr.) Name
o1-01
(500H) Drive Mode Unit Monitor
Selection
o1-02
(501H)
User Monitor Selection after
Power Up
o1-03 Digital Operator Display Unit
(502H) Selection
o1-04
V/f Pattern Setting Units
(503H)
o1-10 User-Set Display Units Maximum
(520H) Value
o1-11 User-Set Display Units Decimal
(521H) Display
o1-12
Length Units
(739H)
o1-20
Traction Sheave Diameter
(575H)
o1-21
Roping Ratio
(576H)
364
V/f OLV
Sets the current level (E5-03) as a percentage for detecting polarity during Initial Polarity
Estimation.
V/f OLV
0: Disabled
1: Enabled
V/f OLV
Sets a delay time for starting the current signal A/D conversion. This value seldom needs to be
changed.
All Modes
Selects the content of the last monitor that is shown when scrolling through Drive Mode
display. Enter the last three digits of the monitor parameter number to be displayed: U -
All Modes
1: Speed reference (U1-01)
2: Direction
3: Output speed (U1-02)
4: Output current (U1-03)
5: User-selected monitor (set by o1-01)
All Modes
Sets the units the drive should use to display the frequency reference and motor speed monitors.
0: 0.01 Hz
1: 0.01% (100% = E1-04)
2: r/min (calculated using the number of motor poles setting in E2-04, E4-04, or E5-04)
3: User-selected units (set by o1-10 and o1-11)
4: Elevator units 1 (speed in m/s, accel/decel rate and jerk in s)
5: Elevator units 2 (speed in m/s, accel/decel rate in m/s
6: Elevator units 3 (speed in ft/min, accel/decel rate in ft/s
V/f OLV
0: Hz
1: r/min
All Modes
These settings define the display values when o1-03 is set to 3.
o1-10 sets the display value that is equal to the maximum output frequency.
o1-11 sets the position of the decimal position.
V/f OLV
0: Millimeter unit
1: Inch unit
V/f OLV
Sets the traction sheave diameter for display unit calculations.
V/f OLV
Sets the roping ratio.
1: 1:1
2: 1:2
3: 1:3
4: 1:4
YASKAWA ELECTRIC SIEP C710616 38A YASKAWA AC Drive L1000A Technical Manual
Description
CLV CLV/PM
CLV CLV/PM
Description
CLV CLV/PM
Description
2 , jerk in m/s 3 )
2 , jerk in ft/s 3 )
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
Setting Page
common_
Default: 100%
TMonly
Min: 0%
Max: 150%
common_
Default: 0
TMonly
Min: 0
Max: 1
Setting Page
common_
Default:
<4>
TMonly
Min: 0.0 μs
Max: 40.0 μs
Setting Page
Default: 106 (Monitor
common_
TMonly
U1-06)
Min: 105
.
Max: 699
common_
TMonly
Default: 1
Min: 1
Max: 5
common_
TMonly
Default: 1
Min: 0
Max: 6
<21>
common_
Default:
<5>
TMonly
Min: 0
Max: 1
Default:
<20>
common_
Min: 1
TMonly
Max: 60000
Default:
<20>
Min: 0
Max: 3
common_
Default: 0
TMonly
Min: 0
Max: 1
common_ Default: 400 mm
<38>
TMonly
Min: 100 mm
Max: 2000 mm
<38>
common_
TMonly
Default: 2
Min: 1
Max: 4
222
222
223
224
224
224
225
225
225
225
225
226