Mpls-Tp Debug Commands - Alcatel-Lucent 7450 Manual

MPLS-TP Debug Commands

MPLS-TP Debug Commands
The following command provides the debug command for an MPLS-TP tunnel:
tools>dump>router>mpls>tp-tunnel <lsp-name> [clear]
The following is a sample output:
A:mlstp-dutA# tools dump router mpls tp-tunnel
- tp-tunnel <lsp-name> [clear]
- tp-tunnel id <tunnel-id> [clear]
<lsp-name>
<tunnel-id>
<clear>
*A:mlstp-dutA# tools dump router mpls tp-tunnel "lsp-
"lsp-32"
"lsp-40"
*A:mlstp-dutA# tools dump router mpls tp-tunnel "lsp-32"
Idx: 1-32 (Up/Up): pgId 4, paths 2, operChg 1, Active: Protect
TunnelId: 42::0.0.3.233::32-42::0.0.3.234::32
PgState: Dn, Cnt/Tm: Dn 1/000 04:00:48.160 Up:3/000 00:01:25.840
MplsMsg: tpDn 0/000 00:00:00.000, tunDn 0/000 00:00:00.000
Paths:
Work (Up/Dn): Lsp 1, Lbl 32/32, If 2/128 (1/2/3 : 0.0.0.0)
Tmpl: ptc: , oam: privatebed-oam-template (bfd: privatebed-bfd-template(np)-10 ms)
Bfd: Mode CC state Dn/Up handle 160005/0
Bfd-CC (Cnt/Tm): Dn 1/000 04:00:48.160 Up:1/000 00:01:23.970
State:
DnReasons: ccFault ifDn
Protect (Up/Up): Lsp 2, Lbl 2080/2080, If 3/127 (5/1/1 : 0.0.0.0)
Tmpl: ptc: privatebed-protection-template, oam: privatebed-oam-template (bfd: pri-
vatebed-bfd-template(np)-10 ms)
Bfd: Mode CC state Up/Up handle 160006/0
Bfd-CC (Cnt/Tm): Dn 0/000 00:00:00.000 Up:1/000 00:01:25.410
State:
Aps: Rx - 5, raw 3616, nok 0(), txRaw - 3636, revert Y
Pdu: Rx - 0x1a-21::0101 (SF), Tx - 0x1a-21::0101 (SF)
State: PF:W:L LastEvt pdu (L-SFw/R-SFw)
Tmrs: slow
Defects: None
Seq
===
000
001
002
003
004
005
Page 102
: [32 chars max]
: [1..61440]
: keyword - clear stats after reading
"lsp-33" "lsp-34"
"lsp-41"
wpDn 0/000 00:00:00.000, ppDn 0/000 00:00:00.000
wpDel 0/000 00:00:00.000, ppDel 0/000 00:00:00.000
tunUp 1/000 00:00:02.070
Admin Up (1::1::1)
Admin Up (1::1::1)
Now: 000 05:02:19.130
Event state TxPdu
====== ======== ==========
start UA:P:L SF (0,0)
pdu UA:P:L SF (0,0)
pdu UA:P:L SF (0,0)
pUp NR NR (0,0)
pdu NR NR (0,0)
wDn PF:W:L SF (1,1)
"lsp-35" "lsp-36" "lsp-37"
port Up , if Dn , operChg 2
port Up , if Up , operChg 1
RxPdu Dir
========== =====
NR (0,0) Tx-->
SF (0,0) Rx<--
NR (0,0) Rx<--
NR (0,0) Tx-->
NR (0,0) Rx<--
NR (0,0) Tx-->
"lsp-38" "lsp-39"
Act Time
==== ================
Work 000 00:00:02.080
Work 000 00:01:24.860
Work 000 00:01:26.860
Work 000 00:01:27.440
Work 000 00:01:28.760
Prot 000 04:00:48.160
7450 ESS MPLS Guide