Appendix D: Event Log Messages - Honeywell GX-Series Installation And Setup Manual

Appendix D: Event Log Messages

KEYPAD TEXT
0001 + CU-BATT Control Unit Standby Battery Low has occurred (battery voltage below
10.2VDC).
0001 - CU-BATT Control Unit Standby Battery Low has finished (battery voltage now above
10.2VDC).
0002 + CU-AC Control Unit Mains (a.c.) Power Fail has occurred.
0002 - CU-AC Control Unit Mains (a.c.) Power Fail has finished.
0003 + LID TAMP Lid Tamper on control unit has occurred.
0003 - LID TAMP Lid Tamper on control unit has finished.
0004 + AUX TAMP Auxiliary Tamper on control unit has occurred.
0004 - AUX TAMP Auxiliary Tamper on control unit has finished.
+ABORT SET Setting process aborted
+AC+BATT AC Fail and battery voltage low.
+ AC FAIL AC Fail zone activated (opened) or an AC Fail on a Power Supply Unit.
– AC FAIL AC Fail zone de-activated (closed) or an AC Fail on a Power Supply Unit has
stopped.
+ALARM EXT Alarm extend zone activated.
ALM CAUSE Reset of system required by entry of an alarm cause code.
ADDED Engineer has added a Module to the system.
ARC TEST Alarm Receiving Centre Test
+ATM-1 ATM-1 zone activated.
+ATM-2 ATM-2 zone activated.
+ATM-3 ATM-3 zone activated.
+ATM-4 ATM-4 zone activated.
AUTOTEST Automatic Test of the system via a comms Module
+AUTOTIMER Autoset timer activated.
–AUTOTIMER Autoset timer de-activated.
BURG HIGH High priority intruder alarm zone open
BURG LOW Low priority intruder alarm zone open.
◊
Fault on battery protection
+BAT FUSE
+ BATT LOW Battery Low activated on Power Supply Unit.
– BATT LOW Battery Low de-activated on Power Supply Unit.
+BEAM PAIR Beam Pair zones activated (opened).
+BEGIN SET Setting process started.
+ BELL FAIL Bell Fail zone opened.
+ BELL TAMP Bell Tamper zone activated (opened).
– BELL TAMP Bell Tamper zone de-activated (closed).
BOOT UP System has been started up or restarted.
CANCEL Alarm activation Cancelled by a valid user Code (system or Group(s) still Set).
COMM FAIL Communication Failure has occurred on a comms Module.
CONFIRM Two independent alarms.
COPY SITE Remote Copy of the Site (system) has occurred via Remote Servicing or the
RS232 Module.
CUSTOM- Custom-A zone activated (opened).
CUSTOM-B Custom-B zone activated (opened).
◊
Control Unit protection trouble.
+CU-FUSE
DELAY ALM PA Delay Alarm zone activated after PA Delay timeout.
◊
The PC board uses a PTC device instead of a fuse. The PTC serves as an automatically resetting fuse.
GX-Series Control Panel Installation and Setup Guide
DESCRIPTION
D-1
TRIGGER
EVENT
13. Elec Status M
20. Fault
13. Elec. Status M
13. Elec. Status M
20. Fault
13. Elec. Status M
9. Tamper M
18. Zone restoral M
9. Tamper M
9. Tamper M
18. Zone restoral
11. Reset NM
13. Elec. Status M
20. Fault
13. Elec. Status M
20. Fault
13. Elec. Status M
20. Fault
3. 24 Hours M
16. Log Zone
Always TR M
9. Tamper M
Always TR NM
3. 24 Hours NM
16. Log Zone
3. 24 Hours NM
16. Log Zone
3. 24 Hours NM
16. Log Zone
3. 24 Hours NM
16. Log Zone
Always TR
None NM
None NM
2. Intrude M
18. Zone Restoral
2. Intrude M
18. Zone Restoral
13. Elec Status M
20. Fault
13. Elec. Status M
20. Fault
13. Elec. Status M
20. Fault
2. Intruder NM
None NM
16. Log Zone NM
9. Tamper M
9. Tamper M
18. Zone restoral
13. Elec. status NM
11. Reset/Cancel NM
20. Fault M
2. Intruder M
None NM
5. Custom zones NM
16. Log Zone
5. Custom Zones NM
16. Log Zone
9. Tamper M
13. Elec Status
20. Fault
1. PA/duress M