Docomo F-01A Instruction Manual page 510

Upper slot : Command
Lower slot : Example
AT+CLIR=<n>
AT+CLIR=2
OK
AT+CMEE=<n>
AT+CMEE=0
OK
AT+CNUM
AT+CNUM
+CNUM : ,"090XXXXXXXX",
129
OK
AT+COPS=<n>,2,<oper>
AT+COPS=0
OK
AT+CPAS
AT+CPAS
+CPAS : 0
OK
AT+CPIN="<pin>",
"<newpin>"
AT+CPIN="0000"
OK
AT+CR=<n>
AT+CR=0
OK
AT+CRC=<n>
AT+CRC=0
OK
AT+CREG=<n>
AT+CREG=0
OK
*2
Set whether to send phone number to the receiver when sending 64K data communication.
n=0 : Use the setting in service agreement
n=2 : Send (default)
AT+CLIR? : Display the current settings and status in the "+CLIR : <n>,<m>" format
m=0 : CLIR not operating (always sends)
m=2 : Unknown m=3 : CLIR temporary mode (default=does not send)
m=4 : CLIR temporary mode (default=sends)
AT+CLIR=? : Display a list of assignable values
*1
Set whether to display an error report at FOMA terminal.
n=0 : Display "ERROR" and no result code (default)
n=1 : Use result code, displaying reason as number
n=2 : Use result code, displaying reason as alphabetic characters
Display reasons in the "+CME ERROR : xxxx" format when n=1 or n=2 is set (xxxx = number
or alphabetic characters).
AT+CMEE? : Display current settings
AT+CMEE=? : Display a list of assignable values
Display FOMA terminal's own phone number in the "+CNUM : ,"<number>",<type>" format.
number : Own phone number (With 2in1, display Number A in Dual mode or A mode and
Number B in B mode)
type=129 : International access code + not included
type=145 : International access code + included
*2
Set search method for network operator to connect.
n=0 : Auto (default)
When n=1 is set, set PLMN Number in hexadecimal value for <oper>.
AT+COPS? : Display current settings
AT+COPS=? : Display a list of assignable values
Display whether FOMA terminal can send and receive AT commands to external devices in
"+CPAS : <n>" format.
n=0 : Possible n=1 : Impossible
n=3 : Possible and receiving
AT+CPAS=? : Display a list of displayable values
Enter these commands for entering PIN/PIN2 codes or PUK. To enter PUK, enter new PIN/
PIN2 code in <newpin>. Even if entering in <newpin> when entry of PIN/PIN2 code is
request, PIN/PIN2 code cannot be changed.
AT+CPIN? : Display the code currently requested in "+CPIN : <n>" format
n=READY : Entry of code not requested
n=SIM PIN2 : Entry of PIN2 code waited
n=SIM PUK : Entry of PUK waited due to failure in unblocking PIN code
n=SIM PUK2 : Entry of PUK waited due to failure in unblocking PIN2 code
*1
Set whether to display the communication type before "CONNECT" is displayed during
connection.
n=0 : Not display (default)
n=1 : Display the communication type in the "+CR : <serv>" format
serv=GPRS : Packet communication
serv=AV64K : 64K videophone
AT+CR? : Display current settings
*1
Set whether to use +CRING result codes when communication is received.
n=0 : Not use (default)
n=1 : Use "+CRING : <type>" result codes
type=GPRS "PPP",,,"<APN>" : Packet communication
type=SYNC : 64K data communication
AT+CRC? : Display current settings
AT+CRC=? : Display a list of assignable values
*1
Set whether to display network information indicating Within service area or Out of service
area.
n=0 : Not notified (default)
n=1 : When the terminal is moved from Within service area to Out of service area or vice
versa, the status is reported in the "+CREG : <stat>" format.
stat=0 : Out of service area
stat=5 : Within service area (during international roaming)
AT+CREG? : Display the current settings and status in the "+CREG : <n>,<stat>" format
AT+CREG=? : Display a list of assignable values
Description
n=1 : Not send
m=1 : CLIR operating (never sends)
P43 "Error messages list"
n=1 : Manual n=3 : No mapping
n=2 : Status unknown
n=4 : Possible and communicating
n=SIM PIN : Entry of PIN code waited
serv=SYNC : 64K data communication
AT+CR=? : Display a list of assignable values
type=AV64K : 64K videophone
stat=1 : Within service area
41
stat=4 : Unknown