Mitsubishi Electric CC-Link IE TSN User Manual page 158

Error code Error type
3001H Moderate
error
3601H Moderate
error
3C00H Major error
3C01H Major error
3C0FH Major error
3C10H Major error
3C13H Major error
3C14H Major error
3C2FH Major error
3E00H Major error
*1*2
D000H Minor error
*1*2
D001H Minor error
10 TROUBLESHOOTING
156
10.7 Error Code List
Error name Error definition and causes
CC-Link IE Field One of the following is detected.
Network Station No. • There is a station with the same
duplication detection station number on the same CC-Link
IE Field Network.
• There are multiple master stations
and sub-master stations on the same
CC-Link IE Field Network.
• There is a CC-Link IE Controller
Network (twisted pair cable) station
on the same CC-Link IE Field
Network.
Inter-module The NZ2GN-GFB is set to
synchronization target "Synchronous" in the network
mismatch configuration settings of the CC-Link IE
Field Network master station.
Hardware error Module hardware error
Hardware error Module hardware error
Hardware error Module hardware error
Hardware error Module hardware error
Hardware error Module hardware error
Hardware error Module hardware error
Hardware error Module hardware error
CC-Link IE Field An error was detected in the CC-Link IE
Network error Field Network.
CC-Link IE TSN Invalid network settings are received.
Communication setting
error 1
CC-Link IE TSN Network settings that cannot be
Communication setting handled by the NZ2GN-GFB are
error 2 received.
Action
• Correct the station number or station type of the station
where the error was detected.
• Divide it into CC-Link IE Controller Network (twisted
pair cable) and the network.
• After taking the above action, power off and on or reset
all stations where the error was detected.
In the network configuration settings of the CC-Link IE
Field Network master station, Set the bridge module to
"Asynchronous".
• Power off and on the NZ2GN-GFB.
• If this error occurs again, the possible cause is a
module failure. Please consult your local Mitsubishi
representative.
• Power off and on the NZ2GN-GFB.
• Take measures against noise with a shielded cable for
connection.
• If this error occurs again, the possible cause is a
module failure. Please consult your local Mitsubishi
representative.
• Power off and on the NZ2GN-GFB.
• Take measures against noise with a shielded cable for
connection.
• If this error occurs again, the possible cause is a
module failure. Please consult your local Mitsubishi
representative.
• Power off and on the NZ2GN-GFB.
• Take measures against noise with a shielded cable for
connection.
• If this error occurs again, the possible cause is a
module failure. Please consult your local Mitsubishi
representative.
• Power off and on the NZ2GN-GFB.
• Take measures against noise with a shielded cable for
connection.
• If this error occurs again, the possible cause is a
module failure. Please consult your local Mitsubishi
representative.
• Power off and on the NZ2GN-GFB.
• If this error occurs again, the possible cause is a
module failure. Please consult your local Mitsubishi
representative.
• Power off and on the NZ2GN-GFB.
• If this error occurs again, the possible cause is a
module failure. Please consult your local Mitsubishi
representative.
• Power off and on the NZ2GN-GFB.
• If this error occurs again, the possible cause is a
module failure. Please consult your local Mitsubishi
representative.
• Power off and on the NZ2GN-GFB.
• If this error occurs again, the possible cause is a
module failure. Please consult your local Mitsubishi
representative.
• Check that the model name of the CC-Link IE TSN
device station set in the network configuration settings
of the CC-Link IE TSN master station matches the
model name of the actual device.
• If this error occurs even when the model names match,
the possible cause is a module failure. Please consult
your local Mitsubishi representative.