Table of Contents
Advertisement
Available languages
Available languages
NOTE: WWAN is a specific 4G mode and is usually more robust than PPP.
1.
Navigate to Configuration.
2.
Select Interface.
3.
General and select WAN = modem (WWAN)
4.
Navigate to Configuration>Interface>WWAN and enter APN applicable for
the selected 4G operator. Leave remaining fields empty.
5.
Press Save at the bottom of the page.
To configure PPP (4G)
2
1
5
1.
Navigate to Configuration.
2.
Select Interface.
3.
General and select WAN = modem (PPP).
4.
Navigate to Configuration>Interface>PPP modem and enter APN applicable
for the selected 4G operator. Leave remaining fields empty.
5.
Press Save at the bottom of the page.
To configure current limit
2
1
NOTE: Change the settings of the current limit if the current limit must be lower
that the charging status fuse level.
Navigate to Configuration.
1.
2.
Select Outlet.
3.
Change the settings for the current limit.
CTEK AB
To configure URL and charging station identity (ChargeboxID) to the
portal
1.
Do a check of the status page to make sure that the internet access op-
erates correctly.
2.
Make sure that the OCPP ChargeboxID and server address is known. This
information should be provided by the portal operator. If CTEK's portal
"Charge Portal" is used, the URL to the portal has the format that follows:
wss://<companyname>.oamportal.com/Ocpp/websocket.
NOTE: The ChargeboxID must be unique and not contain more than 22
characters. The selected portal must support OCPP v1.5 or v1.6.
3.
Navigate to Configuration>Backend and enter the ChargeboxID.
4.
Set the communication protocol to OCPP v1.5 or v1.6.
Enter the backend address. Usually the other parameters may remain
5.
3
unchanged.
6.
Press Save at the bottom of the page.
4
7.
Navigate to the status page and verify that the portal communication is
established.
To configure RFID
1
NOTE: For chargers without portal connection you can only add and remove RFID
tags from the web interface in the charger. For connected chargers you can only
change in the portal.
1.
Navigate to Configuration>Outlet>Authentication and select RFID for all
outlets to activate RFID authentication with RFID tag before charging.
3
2.
Add and delete approved RFID tags under Tag admin.
User & installation instructions
To do a installation tests
•
Make sure that the charging station is firmly mounted on the wall/pole.
•
Check the connection of the power cable and network cable. Tighten the
cable gland if it is necessary.
•
If the installation is a Nanogrid Home setup, check the Communication
between the external EM and the Charger
•
Charge a vehicle. Check the current and make sure that charging symbols
on the display operate correctly.
-
-
•
Make sure that the weather protection of the lock is sealed correctly.
•
Make sure that the display is lit.
•
When the vehicle is charging, make sure that the LEDs on the protection
cover are green.
•
Press the RCD test button on the protection cover to test the earthfault-
testing functionality. Charging should stop. To reset unplug and plug the
charging cable.
•
Ensure the latest version of firmware is intalled before handover.
To do maintenance tests
2
Maintenance on the product must be done once a year.
•
Ensure that the charging outlet/charging cable is in good condition.
•
Replace the charging outlet/charging cable if it is necessary.
3
•
Check the rubber gaskets. Remove any possible dirt from the rubber
gasket.
•
If necessary, update the software.
•
Check the cable gland. Tighten if it is necessary.
•
Any damaged components must be replaced using CTEK approved or
original parts.
To recycle the product
The product must be recycled as electronic equipment. Follow the local
requirements for recycling of electronic equipment.
Function control RFID
Internet connection (4G/Router/Ethernet)
9
Advertisement
Chapters
Table of Contents
