MacDon M Series Assembly Instructions Manual page 74

D 1 1 5 || R E A D
L1
C 1 1 4 ||
L2
Y
L1
E
S
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
D 1 1 5 || A C T I V A T E
L1
C 1 1 4 ||
L2
Y
E L1
S
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
Form # 169242
UNLOADING AND ASSEMBLY
S E N S O R I N P U T S ?
N O / Y E S
D 1 1 5 || S E N S O R
I N P U T
C 1 1 4 || H D R
H E I G H T
D 1 1 5 || S E N S O R
I N P U T
C 1 1 4 || H D R
A N G L E
D 1 1 5 || S E N S O R
I N P U T
C 1 1 4 || K N I F E
S P E E D
D 1 1 5 || S E N S O R
I N P U T
C 1 1 4 ||
R E E L S P E E D
D 1 1 5 || S E N S O R
I N P U T
C 1 1 4 || W H E E L
S P E E D
D 1 1 5 || E X I T
R E A D
C 1 1 4 ||
N O / Y E S
D 1 1 5 || S E N S O R
I N P U T
C 1 1 4 || H D R
H E I G H T
D 1 1 5 || S E N S O R
I N P U T
C 1 1 4 || H D R
A N G L E
D 1 1 5 || S E N S O R
I N P U T
C 1 1 4 || K N I F E
S P E E D
D 1 1 5 || S E N S O R
I N P U T
C 1 1 4 ||
R E E L S P E E D
F U N C T I O N S ?
N O / Y E S
D 1 1 5 || A C T I V A T E
C 1 1 4 || H E A D E R
D 1 1 5 || A C T I V A T E
C 1 1 4 ||
R E E L
D 1 1 5 || A C T I V A T E
C 1 1 4 || H D R
T I L T
D 1 1 5 || A C T I V A T E
C 1 1 4 || K N I F E
D R I V E
D 1 1 5 || A C T I V A T E
C 1 1 4 || D R A P E R / A U G E R
D 1 1 5 || A C T I V A T E
C 1 1 4 ||
R E E L
D 1 1 5 || A C T I V A T E
C 1 1 4 ||
N O / Y E S
D 1 1 5 || A C T I V A T E
C 1 1 4 ||
C A N C E L
D 1 1 5 || P U R G E
C Y C L E
C 1 1 4 ||
C A N C E L
D 1 1 5 || P U R G E
C Y C L E
C 1 1 4 ||
N O E X I T
D 1 1 5 || E X I T
F U N C T I O N
C 1 1 4 ||
N O / Y E S
A C T I V A T E
3 . 5 9 V
1 . 8 4 V
1 2 3 H Z
1 2 3 H Z
1 2 3 H Z
S E N S O R S ?
S E N S O R
S E N S O R
S E N S O R
S E N S O R
F O R C E
F U N C T I O N S ?
D O W N / U P
F U N C T I O N S ?
D O W N / U P
F U N C T I O N S ?
I N / O U T
F U N C T I O N S ?
O N
F U N C T I O N S ?
O N
F U N C T I O N S ?
F O R E / A F T
P U M P D R V S ?
P U M P D R V S ?
S T A R T
S T A R T E D
W A I T
E N D E D
Y E S
M E N U ?
72
If "NO" then jump to:
F U N C T I O N S ?
For diagnostic purposes each sensors input
signal can be read. This helps in determining
how each sensor is operating and if the proper
output voltages are being received by the control
system.
Add a selection to be able to read in the wheel speed
frequency.
If "NO" then jump to:
S E N S O R I N P U T
H D R H E I G H T
If a sensor has been disabled "SENSOR" will be
flashing in the area where the input reading
would have been.
If "NO" then jump to:
H E A D E R T Y P E ?
For diagnostic purposes each header function
can be activated by using the "arrow" keys on the
CDM. When "SELECT" is pressed the program
will go to the next function that can be activated.
If a disk header is detected then the nomeclature
should read: DISC DRIVE instead of KNIFE
DRIVE.
PWM OPERATION: If the HAZARD switch is
pressed instead of the TURN SIGNAL switch the
GSL will operate the PWM valve (HAZARD sw
must be held) and the PWM value will reset to
zero when released.
ACTIVATE PUMP DRIVES - This is to allow the
operator to purge the air from a new or changed
pump system.
Depending upon which program is installed,
pressing the START activates a predetermined
timed purge cycle. Pressing CANCEL or a
completed cycle will jump to the PURGE CYCLE
ENDED menu selection.
If "NO" then jump to:
H E A D E R D O W N / U P
(continued next page)
3 . 5 9 V
Model Year - 2009