MacDon M Series Assembly Instructions Manual page 73

D 1 1 5 || T O
L1
C 1 1 4 ||
L2
C 1 1 4 ||
L2
C 1 1 4 || E X I T
L2
D 1 1 5 || H D R
L1
C 1 1 4 || E X T E N D
L2
D 1 1 5 || C A L I B R A T I N G
L1
C 1 1 4 || E X T E N D
L2
C 1 1 4 || E X T E N D
L2
D 1 1 5 || C A L I B R A T I N G
L1
C 1 1 4 || R E T R A C T
L2
C 1 1 4 || H D R
L2
D 1 1 5 || T O
L1
C 1 1 4 ||
L2
C 1 1 4 ||
L2
C 1 1 4 || E X I T
L2
L1 D 1 1 5 || D I A G N O S T I C
L2 C 1 1 4 ||
Y
D 1 1 5 || V I E W
L1
E
S
C 1 1 4 ||
L2
Y
L1
E
S
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
D 1 1 5 || E N T E R
L1
C 1 1 4 ||
L2
Y
L1
E
S
L2
L1
L2
L1
L2
L1
L2
L1
L2
Form # 169242
UNLOADING AND ASSEMBLY
C A L I B R A T E
H E A D E R H E I G H T
H E A D E R T I L T
C A L ? N O / Y E S
T I L T S E N S O R
T L T T O
T I L T
T I L T
T I L T
T I L T
T I L T
T I L T C O M P L E T E
C A L I B R A T E
H E A D E R H E I G H T
H E A D E R T I L T
C A L ? N O / Y E S
M O D E ?
N O / Y E S
E R R O R C O D E S ?
N O / Y E S
D 1 1 5 || V I E W
T R A C T O R
||
C 1 1 4 ||
N O / Y E S
1 || 1 2 3 4 . 5
||
4 7 || S E N S O R
E
2 || 1 2 3 0 . 5
||
7 1 || L O W
E H Y D R A U L I C
D 1 1 5 || E X I T
T R A C T O R
C 1 1 4 ||
N O / Y E S
D 1 1 5 || V I E W
E N G I N E
C 1 1 4 ||
N O / Y E S
1 || 1 2 3 4 . 5
||
4 4 9 || F U E L
P R E S S U R E
D 1 1 5 || E X I T
E N G I N E
C 1 1 4 ||
N O / Y E S
D 1 1 5 || E X I T
E R R O R
C 1 1 4 ||
N O / Y E S
S E N S O R
N O / Y E S
D 1 1 5 || K N I F E
S P E E D
C 1 1 4 ||
E N A B L E / D I S A B L E
D 1 1 5 || R E E L
S P E E D
C 1 1 4 ||
E N A B L E / D I S A B L E
D 1 1 5 || H E A D E R
C 1 1 4 ||
E N A B L E / D I S A B L E
D 1 1 5 || H E A D E R
C 1 1 4 ||
E N A B L E / D I S A B L E
D 1 1 5 || E X I T
S E N S O R
C 1 1 4 ||
N O / Y E S
S E L E C T
The operator can select any of the three items requiring
calibration (or exit the CAL menu) by using the turn signal
switches to cycle through the choices. Pressing SELECT will
take the operator to the calibration menu for that particular
C A L
The display will indicate the sensor being calibrated. The
S T A R T
operator will be prompted to extend the header tilt and HOLD will
flash until the system has completed reading in the signal with
the header tilt fully extended. HOLD will change to DONE (with
H O L D
D O N E
When the header tilt extend is done, the CDM will prompt the
user to press the header tilt retract. COMPLETE (with buzzer)
H O L D
will flash on the screen for 2 seconds when the calibration is
S E L E C T
Select any of the sensors by using the turn signal switches to
cycle through the choices. Pressing SELECT will take the
operator to the calibration menu for that particular sensor. NO is
the default for EXIT CAL?. If "NO" then jump to:
T O C A L I B R A T E
If "NO" then jump to:
T R A C T O R S E T U P ?
E N T E R
C O D E S ?
H R S 1 2 3
V O L T S L O W
H R S 1 2 3
O I L
C O D E S ?
C O D E S ?
H R S 1 2 3
H I G H
C O D E S ?
C O D E S ?
S E T U P ?
R E A D
S E N S O R
S E N S O R
H T S E N S O R
T I L T S E N S O R
S E T U P ?
71
sensor or to the next main menu.
buzzer) when the reading is completed.
finished.
S E L E C T
If "NO" then jump to:
S E N S O R S E T U P ?
If "NO" then jump to:
V I E W E N G I N E
The last 10 distinct error codes are stored along
with the code #, Exxx, engine hours and number
of occurrences. The "arrow" keys are used to
cycle between codes.
If "NO" then jump to the first error code logged.
If "NO" then jump to:
E N T E R S E N S O R
The last 10 distinct error codes are stored.
If "NO" then jump to the first engine error code
logged.
If "NO" then jump to:
V I E W T R A C T O R
If "NO" then jump to:
S E N S O R I N P U T S ?
The operator can select each sensor and
selectively enable or disable the sensor. This can
be used to disable a failed sensor to eliminate
false or erratic display readings.
When "SELECT" is pressed the program goes to
the EXIT SENSOR SETUP? menu selection.
If "NO" then jump to:
K N I F E S P E E D
(continued next page)
C O D E S ?
S E T U P ?
C O D E S ?
S E N S O R
Model Year - 2009