Page 1 POSITIP 8013 ACTIVE Operating Instructions Digital Readout English (en) 01/2018...
Page 2: Table Of Contents
14 File management..........................217 15 Settings............................227 16 Service and maintenance......................277 17 What to do if ..........................285 18 Removal and disposal........................291 19 Specifications..........................293 20 Index...............................299 21 List of figures..........................302 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 3 Personnel qualification........................25 Obligations of the operating company....................26 General safety precautions......................... 26 2.7 .1 Symbols in the instructions..................... 27 2.7 .2 Symbols on the product......................27 2.7 .3 Electrical safety precautions....................28 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 4 General information..........................41 Product overview..........................42 Connecting encoders........................... 44 Connecting touch probes........................45 Wiring switching inputs and outputs....................46 Connecting a printer..........................50 Connecting a network peripheral.......................51 Connecting the line voltage........................52 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 5 6.9.3 Calculator..........................76 6.10 OEM bar..............................77 6.10.1 Operating elements of the OEM bar..................77 6.10.2 Calling the functions of the OEM bar..................78 6.11 Messages and audio feedback......................79 6.11.1 Messages..........................79 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 6 7 .4.4 Adjusting the display......................111 Backup configuration.........................112 Setup..............................113 Overview............................. 114 Logging in for setup.......................... 115 Individual setup steps........................117 8.3.1 Basic settings.........................117 8.3.2 Setting the application (optional)................... 133 Backup configuration.........................143 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 7 Programming the row of holes..................... 160 9.8.6 Simulating the program run....................161 Machining a bolt hole circle and row of holes (Program run)............162 9.9.1 Opening the program......................162 9.9.2 Running the program......................163 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 8 Controlling program blocks....................198 12.2.3 Aborting the program run...................... 198 12.2.4 Using the simulation window....................198 12.2.5 Setting the spindle speed......................200 12.3 Managing programs...........................201 12.3.1 Opening a program........................201 12.3.2 Closing a program........................201 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 9 13.6 Running program blocks........................216 14 File management..........................217 14.1 Overview............................. 218 14.2 File types.............................219 14.3 Managing folders and files....................... 220 14.4 Opening and viewing files........................ 223 14.5 Exporting files............................ 224 14.6 Importing files............................ 225 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 10 15.6.6 Overrides..........................250 15.6.7 Adding M functions....................... 250 15.6.8 Configuring M functions......................251 15.6.9 Special settings........................251 15.6.10 Axes X, Y, Z........................... 252 15.6.11 Encoder..........................254 15.6.12 Reference marks (Encoder)....................256 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 11 16 Service and maintenance......................277 16.1 Overview............................. 278 16.2 Cleaning...............................278 16.3 Maintenance schedule........................280 16.4 Resuming operation...........................281 16.5 Updating the firmware........................281 16.6 Restore configuration........................283 16.7 Reset all settings..........................284 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 12 Product dimensions with Single-Pos stand................297 19.3.2 Product dimensions with Duo-Pos stand................297 19.3.3 Product dimensions with Multi-Pos stand................298 19.3.4 Product dimensions with Multi-Pos holder................298 20 Index...............................299 21 List of figures..........................302 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 13: Fundamentals
Fundamentals...
Page 14 If the part numbers and indexes do not match so that the documentation is not valid, you will find the current documentation for the product at www.heidenhain.de. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 15 Would you like to see any changes made, or have you found any errors? We are continuously striving to improve our documentation for you. Please help us by sending your requests to the following e-mail address: userdoc@heidenhain.de HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 16 These instructions must be read and observed by every person who performs any of the following tasks: Mounting Installation Commissioning and configuration Operation Programming Service, cleaning and maintenance Troubleshooting Removal and disposal HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 17 An Operator-type user cannot create additional users, but is allowed to edit various operator-specific settings, such as his name or the language. A user of the Operator group can be logged in automatically as soon as the product is switched HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 18 ... the creation and processing of programs ✓ ✓ ✓ 14 "File management" ... the functions of the "File management" menu ... setting options and associated setting parameters ✓ ✓ ✓ 15 "Settings" for the product HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 19 ✓ ✓ ✓ 19 "Specifications" ... product dimensions and mating dimensions (drawings) This chapter enables accessing the content of these ✓ ✓ ✓ 20 "Index" instructions according to specific topics. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 20 The behavior of the functions depends on the configurable machine settings The book symbol represents a cross reference to external documentation, e.g. the documentation of your machine tool builder or other supplier. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 21 Identifies an item of a list Example: TTL interface EnDat interface Bold Identifies menus, displays and buttons Example: Tap Shut down The operating system shuts down Turn the power switch off HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 23: Safety
Safety...
Page 24 Intended use The products of the POSITIP 8013 ACTIVE series are advanced digital readouts for use on manually operated machine tools. In combination with linear and angle encoders, digital readouts of the POSITIP 8013 ACTIVE series return the position of the tool in more than one axis and provide further functions for operating the machine tool.
Page 25 If any such hazard exists, appropriate measures must be taken by the operating company. In particular, the products of the POSITIP 8013 ACTIVE series must not be used in the following applications: Use and storage outside the operating conditions specified in "Specifications"...
Page 26 The specific safety precautions required for the individual activities to be performed on the product are indicated in the respective sections of these instructions. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 27 Functional ground connection as per IEC/EN 60204-1. Observe the information on installation. Product seal. Breaking or removing the product seal will result in forfeiture of warranty and guarantee. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 28 If you open the product, the warranty and the guarantee will be void. Never open the housing Only the product manufacturer is permitted to access the inside of the product HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 29: Transport And Storage
Transport and storage...
Page 30: Overview
PDF issue of the Operating Instructions on a memory medium in the currently available languages Product Digital Readout POSITIP 8013 ACTIVE Installation Instructions Printed issue of the Installation Instructions in the currently available languages HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 31: Accessories
90°, fixing hole pattern 100 mm x 100 mm Single-Pos stand Stand for rigid mounting, 1089230-01 inclination angle 20°, fixing hole pattern 100 mm x 100 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 32: In Case Of Damage In Transit
Storage of the product Package the product as described above Observe the specified ambient conditions Further information: "Specifications", Page 293 Inspect the product for damage after any transport or longer storage times HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 33: Mounting
Mounting...
Page 34: Overview
Allen key, size 2.5 (Duo-Pos stand) Material for mounting on supporting surface The unit must be mounted to a stand or a holder to ensure the correct and intended use of the product. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 35: Mounting On Stand Single-Pos
Figure 2: Product mounted on Single-Pos Figure 3: Cable routing on Single-Pos stand stand Further information: "Product dimensions with Single-Pos stand", Page 297 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 36: Mounting On Duo-Pos Stand
Figure 4: Product mounted on Duo-Pos stand Figure 5: Cable routing on Duo-Pos stand Further information: "Product dimensions with Duo-Pos stand", Page 297 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 37: Mounting On Multi-Pos Stand
Figure 6: Product mounted on Multi-Pos stand Figure 7: Cable routing on Multi-Pos stand Further information: "Product dimensions with Multi-Pos stand", Page 298 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 38: Mounting On Multi-Pos Holder
Figure 8: Product mounted on Multi-Pos Figure 9: Cable routing on Multi-Pos holder holder Further information: "Product dimensions with Multi-Pos holder", Page 298 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 39: Installation
Installation...
Page 40: Overview
The following steps must be performed only by qualified personnel. Further information: "Personnel qualification", Page 25 The type of connections for encoders may vary depending on the product version. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 41: General Information
Incorrect wiring of inputs or outputs can cause damage to the product or peripheral devices. Comply with the pin layouts and technical data of the product Only assign pins or wires that are used Further information: "Specifications", Page 293 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 42: Product Overview
Functional ground connection as per IEC/EN 60204-1 X116: RJ45 Ethernet connection for communication and data exchange with subse- quent systems or PC X112: 15-pin D-sub connection for touch probes (e.g. HEIDENHAIN touch probe) HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 43 X104: 9-pin D-sub connection for universal relay interface (2x relay changeover contacts) Left side panel 11 X31 (under protective cover): USB 2.0 Hi-Speed connection (Type A) for printer or USB mass storage device HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 44: Connecting Encoders
Connect the encoder cables tightly to the respective connections Further information: "Product overview", Page 42 If the cable connectors include mounting screws, do not overtighten them Pin layout of X1, X2, X3 R– A– Sensor 0 Sensor HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 45: Connecting Touch Probes
If the cable connectors include mounting screws, do not overtighten them Pin layout of X112 LED+ B 5 V B 12 V 12 V DC 5 V DC LED– B – Probe signals, readiness TP – Touch Probe, normally closed HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 46: Wiring Switching Inputs And Outputs
If the cable connectors include mounting screws, do not overtighten them The digital or analog inputs and outputs must be assigned in the device settings of the respective switching function. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 47 Installation | Wiring switching inputs and outputs Pin layout of X104 CO – Change Over NO – Normally Open NC – Normally Closed Relay outputs: HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 48 Dout 1 Dout 3 Dout 5 Dout 7 DC 24 V Digital inputs: Digital outputs: X105 X105 Din 0...23 Pin 17, 18, 36 DC 24 V DC 24 V Dout 0...7 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 49 Aout 0+ Aout 1+ Aout 2+ Aout 3+ Ain 1 Ain 3 Aout 0– Aout 1– Aout 2– Aout 3– DC 5 V Ain 0 Ain 2 Analog inputs: Analog outputs: HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 50: Connecting A Printer
The cable connector must firmly engage in the port Further information: "Product overview", Page 42 Pin layout of X116 1 2 3 4 5 6 7 8 D1– D3– D2– D4– (TX+) (TX–) (RX+) (RX–) HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 51: Connecting A Network Peripheral
CAT.5 cable. The cable connector must firmly engage in the port Further information: "Product overview", Page 42 Pin layout of X116 1 2 3 4 5 6 7 8 D1– D3– D2– D4– (TX+) (TX–) (RX+) (RX–) HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 52: Connecting The Line Voltage
Use a power cable that meets the requirements to connect the power connection to a 3-wire grounded power outlet Further information: "Product overview", Page 42 Pin layout X100 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 53: Basic Operation
Basic operation...
Page 54: Overview
Malfunctions of the touchscreen caused by humidity or contact with water! Humidity or water can impair the proper functioning of the touchscreen. Protect the touchscreen from humidity or contact with water Further information: "Product data", Page 294 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 55: Gestures
The actions initiated by dragging include Scroll lists and texts HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 56: General Operating Elements And Functions
If the entry is incomplete or incorrect, a red exclamation mark is displayed. The entry cannot be concluded in this case To apply the values, confirm the entry with RET The values are displayed The screen keyboard disappears HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 57 Buttons that open drop-down lists are indicated by a triangle pointing down. Tap the button The drop-down list opens The active entry is highlighted in green Tap the desired entry The selected entry is applied HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 58 The new feature is added Close Tap Close to close a dialog Confirm Tap Confirm to conclude an activity Back Tap Back to return to the higher level in the menu structure HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 59: Positip 8013 Active - Switch-On And Switch-Off
Basic operation | POSITIP 8013 ACTIVE – switch-on and switch-off POSITIP 8013 ACTIVE – switch-on and switch-off 6.4.1 Switching on POSITIP 8013 ACTIVE Before using the product, you need to perform the commissioning and setup steps. Depending on the purpose of use, you may have to configure additional setup parameters.
Page 60: Switching Off Positip 8013 Active
Basic operation | POSITIP 8013 ACTIVE – switch-on and switch-off 6.4.3 Switching off POSITIP 8013 ACTIVE NOTICE Damage to the operating system! Disconnecting the power source while the product is on can damage the operating system of the product. Use the Switch-off menu to shut down the product...
Page 61: User Login And Logout
Tap Log out The user is logged out All functions of the main menu are inactive, except for Switch The product can only be used again after a user has logged in HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 62: Setting The Language
After logging in, follow the instructions of the wizard The Reference symbol stops blinking upon successful completion of the reference mark search Further information: "Activating the reference mark search", Page 93 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 63: User Interface
Further information: "Manual operation menu", Page 66 If automatic user login is not active, the product opens the User login menu. Further information: "User login menu", Page 72 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 64: Main Menu Of The User Interface
Program run Execution of a previously created program with operator guidance Further information: "Program run menu", Page 68 Programming Creation and management of individual programs Further information: "Programming menu", Page 69 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 65 Further information: "Settings menu", Page 73 Switch-off Shutdown of the operating system or activation of energy- saving mode Further information: "Switch off menu", Page 74 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 66: Manual Operation Menu
Spindle speed (machine tool) In the Manual operation menu, the workspace shows the position values measured on the machine axes. The status bar provides additional functions. Further information: "Manual operation", Page 165 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 67: Mdi Menu
You specify the distance to the target point, and the distance to go is then calculated and displayed. The status bar provides additional measured values and functions. Further information: "MDI mode", Page 177 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 68: Program Run Menu
You can display a visualization of the selected block in the optional simulation window. The status bar provides additional measured values and functions. Further information: "Program run", Page 193 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 69: Programming Menu
A sequence of blocks then forms a program. You can display a visualization of the selected block in the optional simulation window. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 70 Basic operation | User interface Figure 18: Programming menu with simulation window opened View bar Simulation window (optional) Block parameters Toolbar Program blocks Program management Further information: "Programming", Page 203 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 71: File Management Menu
The USB mass storage devices and the network drives are displayed with their names or drive designations. Further information: "File management", Page 217 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 72: User Login Menu
To log in another user, the logged-in user must log out. Further information: "User login and logout", Page 61 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 73: Settings Menu
Further information: "Settings", Page 227 The product provides various authorization levels that grant the user full or restricted access to management and operation functionality. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 74: Switch Off Menu
Cleaning mode Switches the screen off; the operating system continues unchanged Further information: "POSITIP 8013 ACTIVE – switch-on and switch-off", Page 59 Further information: "Display reinigen", Page 279 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 75: Status Bar
Display of the actual feed rate of the currently fastest axis Override Display of the changed traversing speed of an axis. The change is made using an external controller on an NC- controlled machine tool HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 76: Stopwatch
Stops time measurement and resets it to 0:00:00 6.9.3 Calculator For calculations, the status bar provides a calculator with the basic mathematical functions. To enter the numeric values, use the numeric keys as on a standard calculator. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 77: Oem Bar
NC-controlled machine tool Further information: "Configuring nominal values for the spindle speed", Page 107 Coolant Activates the coolant supply of a connected machine tool Further information: "Configuring special functions", Page 109 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 78: Calling The Functions Of The Oem Bar
Zeroing a tool axis does not overwrite any preset values or tool data. If a preset value is set for the tool axis in the position display, zeroing of the tool axis is reset again. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 79: Messages And Audio Feedback
To close the display area, drag the handle up out of the screen The number of unclosed messages is indicated in Messages Closing messages Tap Close to close a message The message disappears HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 80: Wizard
The wizard proceeds to the next step or concludes the process Tap Next to proceed to the next step Tap Back to return to the previous step Tap Close to close the wizard HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 81: Audio Feedback
The available sounds are grouped into categories. The sounds differ within a category. You can define the audio feedback settings in the Settings menu. Further information: "Sounds", Page 234 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 83: Commissioning
Commissioning...
Page 84: Overview
Make sure that you have read and understood the "Basic Operation" chapter before performing the activities described below. Further information: "Basic operation", Page 53 The following steps must be performed only by qualified personnel. Further information: "Personnel qualification", Page 25 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 85: Logging In For Commissioning
The language selected for the user is indicated by a national flag in the Language drop-down list Select the flag for the desired language in the Language drop-down list The user interface is displayed in the selected language HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 86 Enter the new password and repeat it Confirm entry with RET Tap OK Close the message with OK The new password is available the next time the user logs in HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 87: Steps For Commissioning
Select the desired format in the Date format list: MM-DD-YYYY: Display as month, day, year DD-MM-YYYY: Display as day, month, year YYYY-MM-DD: Display as year, month, day Further information: "Date and time", Page 237 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 88 Additional Software options are enabled for the product via a License key. On the overview page, you can check which Software options are enabled. Further information: "Checking the Software options", Page 92 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 89 Contact a HEIDENHAIN service agency and submit the file you created in order to request a license key for the product The license key and the license file are generated and sent by e-mail HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 90 The license key is activated Tap OK You may need to restart the product, depending on the software option Confirm the restart with OK The activated software option is available HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 91 The license key is activated Tap OK You may need to restart the product, depending on the software option Confirm the restart with OK The activated software option is available HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 92 On the overview page, you can check which Software options are enabled for the product. Tap Settings in the main menu Tap Service Open in the sequence Software options Overview A list of enabled Software options is displayed HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 93: Configuring The Axes
Before you start measuring, you need to configure the parameters of the connected encoders for the individual axes. The parameters of HEIDENHAIN encoders, which are typically connected to the unit, can be found in the overview of typical encoders. Further information: "Overview of typical encoders", Page 96...
Page 94 Confirm the entry with RET As an alternative, you can tap Apply in Current position for reference point shift in order to apply the current position as the offset value HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 95 Positive: The direction of traverse is in the counting direction of the encoder Negative: The direction of traverse is opposite to the counting direction of the encoder Further information: "Axes X, Y, Z", Page 252 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 96 Commissioning | Steps for commissioning Overview of typical encoders The following overview lists the parameters of the HEIDENHAIN encoders that are typically connected to the product. When connecting other encoders, refer to the encoder's documentation for the required parameters. Linear encoders...
Page 97 For all methods, the actual error curve must be exactly measured (e.g., with the help of a comparator measuring device or calibration standard. Linear error compensation and segmented linear error compensation can no longer be combined with each other. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 98 Enter the length of the actual traverse path determined by measure (actual length) Confirm the entry with RET Activate Compensation with the ON/OFF sliding switch Further information: "Linear error compensation (LEC)", Page 257 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 99 Tap Back twice to return to the previous display Activate Compensation with the ON/OFF sliding switch The error compensation for the axis is applied Further information: "Segmented linear error compensation (SLEC)", Page 258 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 100 Tap Back twice to return to the previous display Activate Compensation with the ON/OFF sliding switch The adjusted error compensation for the axis is applied Further information: "Segmented linear error compensation (SLEC)", Page 258 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 101: Using M Functions
Thread cutting OFF Program STOP, spindle STOP, coolant OFF These M functions are independent of the machine; some M functions however depend on the machine tool configuration (e.g. spindle functions). HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 102: Switching Functions
Switching functions Configuring a touch probe You can use probing functions to set presets with a HEIDENHAIN KT 130 Edge Finder. The stylus of the edge finder can be additionally fitted with a ruby ball tip. In order to use the KT 130 edge finder, you need to configure the relevant parameters.
Page 103: Oem Area
Tap Select The file is copied to the Service info area on the product Further information: "Service info", Page 239 Confirm the successful transfer with OK Further information: "Documentation", Page 276 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 104: Adding A Startup Screen
Tap the file name Tap Select The image is copied to the product and displayed as the startup screen the next time the product is started Confirm the successful transfer with OK HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 105: Configuring The Oem Bar
Showing or hiding the OEM bar Tap Settings in the main menu Tap Service Open in the sequence OEM area OEM bar Activate or deactivate Show bar with the ON/OFF sliding switch HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 106 "LogoOEM bar item", Page 271 Navigate to the folder containing the image file, and select the file Tap Select Select the desired option in the Link to documentation drop- down list HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 107 Tap Spindle speed in the Type drop-down list Tap the name of the spindle in the Spindle drop-down list Enter the desired nominal value into the Spindle speed input field HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 108 Tap Select image for inactive function to select the image file you want to use to depict the function Navigate to the folder containing the image file, and select the file Tap Select HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 109 Select image for inactive function to specify the image you want to display to depict the respective status Further information: "Special functionsOEM bar item", Page 273 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 110 Open in the sequence OEM area OEM bar Bar items Tap the desired menu item Tap Remove bar entry Tap OK to confirm deletion The menu item is deleted from the OEM bar HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 111: Adjusting The Display
Defining the keyboard design Tap Settings in the main menu Tap Service Open in the sequence OEM area Settings Select the desired layout for the screen keyboard in the Keyboard theme drop-down list HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 112: Backup Configuration
Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 113: Setup
Setup...
Page 114: Overview
Make sure that you have read and understood the "Basic Operation" chapter before performing the activities described below. Further information: "Basic operation", Page 53 The following steps must be performed only by qualified personnel. Further information: "Personnel qualification", Page 25 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 115: Logging In For Setup
After logging in, follow the instructions of the wizard The Reference symbol stops blinking on successful completion of the reference mark search Further information: "Activating the reference mark search", Page 93 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 116 Enter the new password and repeat it Confirm entry with RET Tap OK Close the message with OK The new password is available the next time the user logs in HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 117: Individual Setup Steps
Select the desired format in the Date format list: MM-DD-YYYY: Display as month, day, year DD-MM-YYYY: Display as day, month, year YYYY-MM-DD: Display as year, month, day Further information: "Date and time", Page 237 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 118 To set the number of decimal places displayed, tap – or + Further information: "Units", Page 237 Entering and configuring users The following user types, which have different rights, are defined in the product's factory default settings: Setup Operator HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 119 Tap OK A message appears Close the message with OK The user is created with the basic data. The user can then further edit the data himself later HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 120 Close the message with OK To change the language, select the flag for the desired language in the Language drop-down list To activate or deactivate Auto login, use the ON/OFF sliding switch HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 121 Tap Settings in the main menu Tap User Tap the user you want to delete Tap Remove user account Enter the password of the authorized user (OEM or Setup) Tap OK The user is deleted HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 122 The Operating Instructions are copied to the product Any existing Operating Instructions will be overwritten Confirm successful transfer with OK The Operating Instructions can be opened and displayed on the product HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 123 Enter the Preferred DNS server and, if required, the Alternative DNS server Confirm the entires with RET The configuration of the network connection is applied Further information: "Network", Page 241 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 124 If required, select Network drive options Select Authentication for encrypting the password in the network Configure the Mount options Tap Mount The connection to the network drive is established Further information: "Network drive", Page 242 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 125 If this list contains the used printer, the appropriate driver is available on the product and you can directly configure the printer. If this is not the case, you will need a printer-specific PPD file. Further information: "Finding PPD files", Page 130 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 126 Select the appropriate driver for the printer type If the appropriate driver is not listed, a suitable PPD file must be copied to the product. Further information: "Finding PPD files", Page 130 The driver is activated HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 127 Use the CUPS web interface to configure the enhanced settings of the connected printer. You can also use this web interface if the printer information fails over the product. Further information: "Using CUPS", Page 131 Further information: "Printers", Page 234 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 128 If the appropriate driver is not listed, a suitable PPD file must be copied to the product. Further information: "Finding PPD files", Page 130 The driver is activated Tap Close in the message Tap Set standard values HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 129 Use the CUPS web interface to configure the enhanced settings of the connected printer. You can also use this web interface if the printer information fails over the product. Further information: "Using CUPS", Page 131 Further information: "Printers", Page 234 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 130 Select the PPD file Tap Select The PPD file is copied to the product Tap Continue The PPD file is loaded and the driver is activated Tap Close in the message HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 131 (e.g. http://10.6.225.86:631) In the web interface, click on the Administration tab and select the desired action See the Online Help tab for detailed information about the CUPS web interface. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 132 The entered values are saved as defaults Depending on the type of printer, select further values such as type of paper or duplex print under Properties Further information: "Printers", Page 234 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 133: Setting The Application (Optional)
Depending on the purpose of use, the setup engineer (Setup) can prepare the product for a special application by creating tool tables and preset tables. The following activities can also be performed by Operator-type users. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 134 Designation that uniquely identifies the tool, such as drill or milling cutter Tool diameter D Diameter of the tool contact surface Tool length L Length of the tool in the tool axis HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 135 To protect the entry for a tool from accidental changes or deletion, tap the Lock symbol next to the tool's entry The symbol changes and the entry is locked Tap Close The Tool table dialog is closed HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 136 The symbol changes and the entry is unlocked Tap Delete A message appears Close the message with OK The selected tool is deleted from the tool table Tap Close The Tool table dialog is closed HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 137 Numeric input; use this method to manually enter the presets into the preset table Presetting by probing can also be performed by Operator-type users, depending on the application. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 138 (three probing procedures with tool, four probing procedures with edge finder) Tap Manual operation in the main menu The user interface for manual operation is displayed Tap Probing on the status bar HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 139 Leave the input field empty to load the measured value To define a new value enter the desired value and confirm with RET Tap Confirm in the wizard The probed coordinate is loaded as preset HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 140 Leave the input field empty to load the measured value To define a new value enter the desired value and confirm with RET Tap Confirm in the wizard The probed coordinate is loaded as preset HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 141 To protect the entry for a preset from accidental changes or deletion, tap the Lock symbol next to the preset's entry The symbol changes and the entry is locked Tap Close The Preset table dialog is closed HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 142 The symbol changes and the entry is unlocked Tap Delete A message appears Close the message with OK The selected preset(s) is/are deleted from the preset table Tap Close The Preset table dialog is closed HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 143: Backup Configuration
Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 145: Quick Start
Quick Start...
Page 146: Overview
"Manual operation", "MDI mode", "Programming" and "Program run". Make sure that you have read and understood the "Basic Operation" chapter before performing the activities described below. Further information: "Basic operation", Page 53 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 147: Requirements
"Defining presets", Page 168 An Operator-type user is logged in The reference mark search was performed Further information: "Conducting the reference mark search", Page 167 A HEIDENHAINKT 130 Edge Finder is available HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 148 The defined Ø 5.0 mm drill is added to the tool table Repeat the sequence for the other tools using the naming convention [type] [diameter] Tap Close The Tool table dialog is closed HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 149: Determining The Preset (Manual Operation Mode)
RET Tap Confirm in the wizard The probed coordinate is loaded in preset 0 Repeat the procedure and define the preset in the Y direction via probing HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 150: Machining A Through Hole (Manual Operation Mode)
On the OEM bar: Tap Coolant ON Predrill the through hole and retract the spindle Keep positions X and Y On the OEM bar: Tap Coolant OFF You have successfully predrilled the through hole HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 151: Drilling Out The Through Hole
On the OEM bar: Tap Coolant ON Drill out the through hole and retract the spindle On the OEM bar: Tap Coolant OFF You have successfully drilled out the through hole HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 152: Machining A Rectangular Pocket (Mdi Mode Of Operation)
X coordinate of center: 80 Y coordinate of center: 50 Side length in X: 110 Side length in Y: 80 Direction: clockwise Finishing allowance: 0.2 Confirm each entry with RET HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 153: Milling The Rectangular Pocket
The product executes the individual steps of the milling procedure On the OEM bar: Tap Coolant OFF Retract the spindle Tap Close Program run is terminated The wizard closes You have successfully machined the rectangular pocket HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 154: Machining A Fit (Mdi Mode Of Operation)
Y coordinate: 50 Z coordinate: drill through To run the block, tap END The positioning aid is displayed If the simulation window is active, the position and traverse path are visualized HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 155: Reaming The Fit
Ream the through hole and retract the spindle On the OEM bar: Tap Coolant OFF Tap Close Program run is terminated The wizard closes You have successfully machined the fit HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 156: Determining The Preset (Manual Operation Mode)
In the Set position values field, enter the value 0 for position value X and position value Y and confirm with RET Tap Confirm in the wizard The probed coordinates are loaded in preset 1 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 157 Activating the preset Tap Presets on the status bar The Presets dialog box opens Tap preset 1 Tap Confirm The preset is set On the status bar is displayed with preset HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 158: Programming A Bolt Hole Circle And Row Of Holes (Programming)
In Name enter the name Example Confirm the entry with RET In Unit for linear values select the mm unit of measure The program has been successfully created; you can then begin with programming HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 159: Programming The Tool
Confirm each entry with RET Leave all the other values as defaults. Tap END to terminate the input process Tap Save program in the program management The program is saved HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 160: Programming The Tool
Depth: -13 Number of rows: 3 Row spacing: 45 Fill mode: frame of holes Confirm each entry with RET Tap Save program in the program management The program is saved HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 161: Simulating The Program Run
Check the view for programming errors, e.g. tool path intersections of holes If there are no programming errors you can machine the bolt hole circle and row of holes HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 162: Machining A Bolt Hole Circle And Row Of Holes (Program Run)
Tap Open program in the program management A dialog box is opened. Select the Internal/Programs storage location in the dialog Tap the file Example.i Tap Open The selected program is opened HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 163: Running The Program
Repeat the process for the row of holes machining block After drilling the row of holes tap Close The machining is terminated The program is reset The wizard is closed HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 165: Manual Operation
Manual operation...
Page 166: Overview
Tap Manual operation in the main menu The user interface for manual operation is displayed Figure 36: Manual operation menu Axis key Reference DRO screen Clear Status bar Spindle speed (machine tool) HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 167: Conducting The Reference Mark Search
Tap Start Existing reference marks are cleared The Reference symbol blinks Follow the instructions of the wizard The Reference symbol stops blinking on successful completion of the reference mark search HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 168: Defining Presets
The following functions are available for probing a workpiece: Icon Function Scheme Probe the edge of a workpiece (one probing procedure) Determine the centerline of a workpiece (two probing procedures) HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 169 Enter the desired value in the Set position values input field: Leave the input field empty to load the measured value To define a new value enter the desired value and confirm with RET HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 170 Manual operation | Defining presets Tap Confirm in the wizard The probed coordinate is loaded as preset HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 171: Setting The Units Of Measure
Deg-Min-Sec: angle in degrees [°], minutes ['] and seconds ["] Tap Close The selected units are displayed in the quick access menu The displayed values are converted to the selected units HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 172: Presetting A Position As Datum
The entered position value is linked with the current position and overwrites the active preset in the preset table The active preset is applied as the new value Perform the desired machining operation, e.g. drilling or milling HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 173: Selecting A Tool
Tap the tool you want to use Tap Confirm The associated tool parameters are applied automatically The selected tool is shown on the status bar Mount the desired tool on the machine tool HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 174: Creating A Tool
To protect the entry for a tool from accidental changes or deletion, tap the Lock symbol next to the tool's entry The symbol changes and the entry is locked Tap Close The Tool table dialog is closed HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 175: Setting The Spindle Speed
Tap the Spindle speed input field, enter the value and tap RET to confirm The product applies the entered spindle speed as the nominal value and controls the spindle of the machine tool accordingly HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 177: Mdi Mode
MDI mode...
Page 178: Overview
Programming mode and then execute them in the Program Run mode. Further information: "Programming", Page 203 Further information: "Program run", Page 193 Activation Tap MDI in the main menu HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 179 MDI mode | Overview Tap Create on the status bar The user interface for the MDI mode is displayed Figure 37: MDI menu View bar Block parameters MDI block Status bar Block tools HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 180: Block Types
(inside contour) Incremental position value, i.e. the position value is referenced to the actual position Only for the Z axis: Drill through without position value specification HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 181: Machining Patterns
Select the tool on the status bar Further information: "Creating a tool table", Page 134 In the appropriate input fields you can load the current axis position with Actual position capture. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 182 Angle of the 1st hole of the bolt hole arc Stepping angle Angle of the circle segment Default: bolt hole circle Depth Target depth for drilling in the Z plane Default: drilling through-holes HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 183 Number of rows Number of rows of holes in the linear hole pattern Row spacing Spacing between the individual rows of holes Fill mode Distribution of holes All holes Frame of holes HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 184 Direction in which the rectangular pocket is roughed out (clockwise or counterclockwise) Default: counterclockwise Finishing allowance Amount of material that is to be left remaining around the rectangular pocket and will be removed in the last pass HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 185 Approaching the starting position is at clearance height at rapid traverse If a target depth was defined, positioning is at Clearance height at the end of machining HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 186: Executing Blocks
NC START key on the machine tool With multi-step blocks, such as machining patterns, tap Next to proceed to the next step in the wizard HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 187 MDI mode | Executing blocks Figure 41: Example of a block in the MDI mode Wizard View bar Distance-to-go display MDI block Status bar Positioning aid Spindle speed (machine tool) HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 188: Using The Simulation Window
The simulation window displays a contour view. The contour view provides the necessary feedback for precisely positioning the tool or for following a contour along the machining plane. The contour view uses the following colors (defaults): HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 189 The simulation window for the currently selected block appears Tap Graphic on the view bar to enlarge the simulation window The parameter view is hidden and the simulation window is enlarged HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 190: Positioning Aid
± 5 mm from the nominal position. The color also changes in the following way: Display of positioning aid Meaning The axis slide is moving away from the nominal position Green The axis slide is moving towards the nominal position HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 191: Setting The Spindle Speed
Tap the Spindle speed input field, enter the value and tap RET to confirm The product applies the entered spindle speed as the nominal value and controls the spindle of the machine tool accordingly HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 193: Program Run
Program run...
Page 194: Overview
In both cases, the wizard guides you through the individual program steps. While running the program, you can use the optional simulation window as a graphic positioning aid for the axes you have to move. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 195 Program run | Overview Activation Tap Program run in the main menu The user interface for program run is displayed View bar Wizard Status bar Program control Spindle speed (machine tool) Program management HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 196: Using The Program
"Managing programs", Page 201 Figure 44: Example of a program in the Program run operating mode View bar Simulation window (optional) Distance-to-go display Toolbar Program blocks Spindle speed (machine tool) Program management HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 197: Running The Program
When the Single Block mode is active, the program stops after each block of the program control (this also includes blocks that do not require any action by the user) HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 198: Controlling Program Blocks
The following options are available on the view bar: Operating element Function Graphic Display of simulation and blocks Graphic-Position Display of simulation, position values and blocks Position Display of position values and blocks HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 199 Tool contour, tool position and tool track (orange) Positioning block (dashed) You can modify the colors and line thicknesses used in the contour view. Further information: "Simulation window", Page 233 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 200: Setting The Spindle Speed
Tap the Spindle speed input field, enter the value and tap RET to confirm The product applies the entered spindle speed as the nominal value and controls the spindle of the machine tool accordingly HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 201: Managing Programs
Tap the folder containing the file Tap the file Tap Open The selected program is loaded 12.3.2 Closing a program Tap Close program in the program management The opened program is closed HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 203: Programming
Programming...
Page 204: Overview
The user interface for programming is displayed Figure 46: Programming menu View bar Toolbar Program management The status bar and the optional OEM bar are not available in the Programming menu. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 205: Block Types
(inside contour) Incremental position value, i.e. the position value is referenced to the actual position Only for the Z axis: Drill through without position value specification HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 206: Coordinate Systems
M function Number of the M function Optional: Selection from function table Dwell time Time interval between machining steps HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 207: Machining Patterns
Select the tool on the status bar Further information: "Creating a tool table", Page 134 In the appropriate input fields you can load the current axis position with Actual position capture. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 208: Creating A Program
Define the relevant parameters, depending on the block type Further information: "Block types", Page 205 Confirm each entry with RET If the simulation window is active, the current block is visualized HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 209: Deleting Blocks
Delete symbol Tap the Delete symbol for the blocks you want to delete in the program The selected blocks are deleted from the program Tap Delete on the toolbar again HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 210: Saving A Program
Tap Save program in the program management The program is saved Figure 47: Example of a program in the Programming operating mode View bar Simulation window (optional) Block parameters Toolbar Program blocks Program management HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 211: Using The Simulation Window
The following options are available on the view bar: Operating element Function Graphic Display of simulation and blocks Graphic-Form Display of simulation, parameters and blocks Form Display of parameters and blocks HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 212: Depiction As Contour View
The contour view uses the following colors (defaults): Figure 48: Simulation window with contour view Machining pattern (white) Current block or machining position (green) Tool contour, tool position and tool track (orange) Positioning block (dashed) HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 213: Activating The Simulation Window
Tap each program block, one after the other The program steps are displayed in the simulation window; you can enlarge the detail view as needed Tap Detail view to enlarge Tap Overview show the overall view HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 214: Managing Programs
Closing a program Tap Close program in the program management The opened program is closed 13.5.3 Saving a program Tap Save program in the program management The program is saved HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 215: Saving The Program Under A New Name
All changes to the program will be automatically saved immediately 13.5.6 Deleting a program Tap Delete the program in the program management Tap Delete selection Tap OK to confirm deletion The program is deleted HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 216: Running Program Blocks
Edit the relevant parameters, depending on the block type Further information: "Block types", Page 205 Confirm each entry with RET Tap Save program in the program management The edited program is saved HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 217: File Management
File management...
Page 218: Overview
Tap File management in the main menu The user interface for file management is displayed Figure 49: File management menu List of available storage locations List of folders in the selected storage location HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 219: File Types
– – *.jpg, *.png, Image files *.bmp ✓ – – – *.csv Text files ✓ ✓ – – *.txt, *.log, Text files *.xml ✓ ✓ – ✓ *.pdf PDF files HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 220: Managing Folders And Files
Tap Select The folder is copied If you copy a folder to the folder it is stored in, the suffix "_1" is appended to the name of the copied folder. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 221 The operating elements are displayed Tap Rename file Tap the input field in the dialog and enter a name for the new file Confirm the entry with RET Tap OK The file is renamed HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 222 Touch the icon of the folder or file you want to delete, and drag it to the right The operating elements are displayed Tap Delete selection Tap Delete The folder or file is deleted HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 223: Opening And Viewing Files
Tap View The file contents are displayed Tap Close to close the view In this view, you can print PDF files on the printer configured in the product by tapping Print. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 224: Exporting Files
Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 225: Importing Files
Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 227: Settings
Settings...
Page 228: Overview
Configuration of interfaces and network drives User Configuration of users Axes Configuration of connected encoders and error compensa- tion Service Configuration of software options, service functions and information Activation Tap Settings in the main menu HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 229: Overview Of The Settings Menu
15.6.8 "Configuring M functions" 15.6.9 "Special settings" 15.7.1 "Firmware information" 15.7.2 "Backup and restore configuration" 15.7.3 "Firmware update" Service 15.7.4 "Reset to factory settings" 15.7.5 "OEM area" 15.7.16 "Documentation" 15.7.17 "Software options" HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 230: General
Free RAM on the system Number of unit starts Number of times the product was started up with the current firmware Operating time Operating time of the product with the current firmware HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 231: Screen And Touch Screen
Tap and drag: Touch the touchscreen and drag the arrow upwards from the lower edge Tap: Touch the touchscreen Tap or axis movement: Touch the touchscreen or move the axis Default setting: Tap and drag HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 232: Display
Default setting: Distance to go with position Position values The position values can describe the actual values or nominal values of the axes. Settings: Actual value Nominal value Default setting: Actual value HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 233: Simulation Window
Tool path Use of the tool track Settings: ON or OFF Default value: ON The Undo buttons enable the color definitions of the simulation window to be reset to factory settings. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 234: Sounds
List of printers configured on the product Properties Settings of the selected default printer Add printer Adds a USB printer or Network printer Remove printer Removes a USB printer or Network printer connected to the product HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 235: Properties
The setting range and default setting depend on the printer type Color/Black and white Specification of the printing mode The setting range and default setting depend on the printer type HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 236: Add Printer
Shows the type of the configured printer Location Shows the location of the configured printer Connection Shows the connection of the configured printer Remove the selected printer Deletes the configured printer from the product HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 237: 15.2.10 Date And Time
Default setting: Commercial Decimal places for linear values Number of decimal places for linear values Setting range: Millimeters: 0 ... 5 Inch: 0 ... 7 Default value: Millimeters: 4 Inch: 6 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 238 Decimal degrees: 0 ... 5 Deg-Min-Sec: 0 ... 2 Default value: Radian: 5 Decimal degrees: 3 Deg-Min-Sec: 0 Decimal separator Separator for the display of values Settings: Point or Comma Default setting: Point HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 239: 15.2.12 Copyrights
Meaning and function Operating Instructions Display of the operating instructions stored on the product Default: no document; the document in the desired language can be added Further information: "Documentation", Page 276 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 240: Sensors
Default setting: OFF Length Length offset of the edge finder Setting range: ≥ 0.0001 Default value: 0.0000 Diameter Diameter of the edge finder Setting range: ≥ 0.0001 Default value: 0.0000 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 241: Interfaces
IPv6 standard gateway Network address of the router connecting a network Preferred DNS server Primary server for mapping the IP address Alternative DNS server Optional server for mapping the IP address HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 242: Network Drive
Kerberos V5 authentication and packet signing NTLM password hashing NTLM password hashing with signing NTLMv2 password hashing NTLMv2 password hashing with signing Default value: None Configuration of the Mount options Settings: Default value: nounix,noserverino HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 243: User
Language of the user – Auto login On restart of the product: Automatic login of the last logged-in user Default value: OFF – Remove user account Removal of the user account HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 244: Setup
Language of the user – Auto login On restart of the product: Automatic login of the last logged-in user Default value: OFF – Remove user account Removal of the user account HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 245: Operator
Path: Parameter Explanation Adds a new user of the type Operator Further information: "Entering and configuring users", Page 118 It is not possible to add further OEM and Setup-type users. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 246: Axes
Start starts the reference mark search and opens the workspace Reference mark search status Indicates whether the reference mark search was successful Display: Successful Unsuccessful Stop of reference mark search Indicates whether the reference mark search was canceled Display: HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 247: Information
Further information: "Inputs (Switching functions)", Page 248 Outputs Assignment of the digital output for the respective switching function according to the pin layout Further information: "Outputs (Switching functions)", Page 249 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 248: Inputs (Switching Functions)
MDI mode and Program Run: The push button functions as an NC START key. Pressing the push button starts and interrupts the cycles of a program block. Default value: Not connected HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 249: Outputs (Switching Functions)
Program Run or if automatic feed rate is activated in manual operation. The lighting blinks if an active cycle is interrupted and can be continued by pressing the NC START key. Default value: Not connected HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 250: Overrides
Settings ► Axes ► General settings ► M functions ► + Path: Parameters Explanation Name Entry of the name for the new M function Setting range: M100 ... M120 For the configuration, see "Configuring M functions", Page 251 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 251: Configuring M Functions
Definition of the axis movements that are possible with the jog buttons traverse keys Settings: ON: Only a single axis can be moved OFF: Several axes can be moved simultaneously Default value: OFF HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 252: 15.6.10 Axes X, Y, Z
Setting range: 50 ms ... 10000 ms Default value: 150 Kv factor P Proportional component of the position controller during positioning Setting range: 0.3 m/(min x mm) ... 6 m/(min x mm) Default value: 2.5 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 253 Setting range: 5 µm ... 1000 µm Default value: 500 Maximum standstill error Definition of the maximum position deviation at a standstill Setting range: 5 µm ... 1000 µm Default value: 100 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 254: 15.6.11 Encoder
Frequency value of the analog low-pass filter (not with TTL) Settings: 33 kHz: Suppression of interference frequencies above 33 kHz 400 kHz: Suppression of interference frequencies above 400 kHz Default value: 400 kHz HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 255 Positive: The direction of traverse corresponds to the counting direction of the encoder Negative: The direction of traverse does not correspond to the counting direction of the encoder Default value: Positive HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 256: Reference Marks (Encoder)
Setting range: > 0° ... 360° Default value: 10.0 Reference point displacement Configuration of the offset between the reference mark and the zero point Further information: "Reference point displacement", Page 257 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 257: 15.6.13 Reference Point Displacement
If Compensation is active, the Nominal length and Actual length cannot be edited or generated. Nominal length Input field for nominal value in mm Actual length Input field for actual value in mm HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 258: Segmented Linear Error Compensation (Slec)
The start point defines the position starting from which the compensation is applied to the axis Default value: 0.00000 Create Creates a new table of supporting points based on the entries HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 259: Outputs
Fmax Setting range: 1000 mV ... 10000 mV Default value: 9000 Drive enable Assignment of the digital output for the drive enable according to pin layout Default value: Not connected HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 260: 15.6.18 Inputs
Assignment of the digital input for the enable signal of the servo amplifier according to pin layout Default value: Not connected Signal is low-active If the function is active, the axis is enabled when the signal is low at the input HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 261: 15.6.19 Software Limit Switches
Limit switch in negative Distance (in mm) in the negative direction from the machine direction datum to the software limit switch (including Reference point displacement, if activated) Default value: 0 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 262: 15.6.20 Spindle Axis S
Setting range: 0 rpm ... 500 rpm Default value: 30 Maximum spindle speed for Definition of the maximum spindle speed for thread cutting thread cutting Setting range: 100 rpm ... 2000 rpm Default value: 1000 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 263: Outputs (S)
Assignment of the digital output for the clockwise spindle enable according to pin layout Default value: Not connected Enable spindle CCW Assignment of the digital output for the counterclockwise spindle enable according to pin layout Default value: Not connected HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 264: Inputs (S)
This signal influ- ences error messages and program run. The machine tool builder is responsible for the immediate shutdown of the spindles with opened spindle protection. Default value: Not connected HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 265 Default value: Not connected Spindle position Assignment of a digital input; the signal positions the spindle at low speed during stopping to a desired position Default value: Not connected HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 266: Service
Version number of the parameters for inputs and outputs info.xml Version number of the information parameters audio.xml Version number of the audio parameters network.xml Version number of the network parameters os.xml Version number of the operating system parameters HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 267: Backup And Restore Configuration
Explanation Restore configuration Restoring of the backed up settings Further information: "Restore configuration", Page 283 Backup configuration Backing up of settings of the product Further information: "Backup configuration", Page 112 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 268: Firmware Update
You can reset the settings of the product to the factory default settings if required. Software options are deactivated and subsequently need to be reactivated with the available license key. Further information: "Reset all settings", Page 284 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 269: Oem Area
OFF: The OEM bar is not displayed Default value: OFF Bar items Configuration of the Bar items on the OEM bar Further information: "Adding OEM-Bar items", Page 270 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 270: Adding Oem-Bar Items
Page 272 Special functions: Further information: "Special functionsOEM bar item", Page 273 Document: Further information: "DocumentOEM bar item", Page 274 Remove bar entry Removing the bar item from the OEM bar HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 271: Logooem Bar Item
Copies a selected image file to the storage location /Oem/ Images File format: PNG, JPG, PPM, BMP or SVG Image size: max. 140 x 70 px Remove bar entry Removing the bar item from the OEM bar HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 272: Spindle Speedoem Bar Item
Copies a selected image file to the storage location /Oem/ Images File format: PNG, JPG, PPM, BMP or SVG Image size: Max. 100 x 70 px Remove bar entry Removing the bar item from the OEM bar HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 273: 15.7.11 Special Functionsoem Bar Item
Copies a selected image file to the storage location /Oem/ Images File format: PNG, JPG, PPM, BMP or SVG Image size: Max. 100 x 70 px Remove bar entry Removing the bar item from the OEM bar HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 274: 15.7.12 Documentoem Bar Item
Selection of the keyboard layout Settings: Standard: entry confirmed with (Return) TNC: entry confirmed with (Enter) Default value: Standard Program run Modifying of the program execution Further information: "Program execution", Page 275 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 275: 15.7.14 Program Execution
Copies a selected image file to the storage location /Oem/ Images File format: PNG, JPG, PPM, BMP or SVG Image size: Max. 100 x 70 px Remove the entry Remove the entry HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 276: 15.7.16 Documentation
Activation of the software options via license key or license file Further information: "Activating a license key", Page 90 Reset trial options Reset of the trial options by entering a license key HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 277: Service And Maintenance
Service and maintenance...
Page 278: Overview
Do not use sharp-edged objects to remove persistent contamination Cleaning the housing Use only a cloth dampened with water and a mild detergent for cleaning the exterior surfaces HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 279 To deactivate the cleaning mode, tap anywhere on the touchscreen An arrow appears at the bottom of the screen Drag the arrow up The screen is switched on and shows the user interface last displayed HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 280: Maintenance Schedule
Contact HEIDENHAIN service and check their function agency if required Check power cables Annually Replace power cables for faulty insulation and according to the specification weak points HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 281: Resuming Operation
Continue The service application is launched Updating the firmware The firmware can be updated from a USB mass storage device (FAT32 format) or via a network drive. Tap Firmware update HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 282 Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 283: Restore Configuration
Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 284: Reset All Settings
Tap OK to confirm the reset Tap OK to confirm shutdown of the product The product is shut down All settings are reset To restart the product, switch it off and then back on HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 285: What To Do If
What to do if ...
Page 286: Overview
17.2.1 Restoring the firmware On a computer, create the folder "heidenhain" on a USB mass storage device (FAT32 format). In the "heidenhain" folder, create the folder "update" Copy the new firmware to the "update" folder...
Page 287: Restore Settings
Malfunctions If faults or malfunctions that are not listed in the "Troubleshooting" table below occur during operation, refer to the machine tool builder's documentation or contact a HEIDENHAIN service agency. HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 288: Troubleshooting
Incorrect feed rate Check the axis settings Qualified not limit the axis speed override settings personnel Rapid traverse key does Incorrect rapid Check settings Qualified not work traverse settings Page 248 personnel HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 289 Use another USB port The type or format- Use another USB mass Qualified ting of the USB mass storage device personnel storage device is not Format USB mass storage supported device with FAT32 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 290 User login is not possible Password does not As a user with a higher Qualified exist authorization level, reset the personnel password Page 118 To reset the OEM password, contact the HEIDENHAIN service agency HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 291: Removal And Disposal
Removal and disposal...
Page 292: Overview
Forward the product to recycling in accordance with the applicable local disposal regulations If you have any questions about the disposal of the product, please contact a HEIDENHAIN service agency HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 293: Specifications
Specifications...
Page 294: Overview
Output current max. 150 mA per channel Relay outputs Max. switching voltage AC 30 V / DC 30 V Max. switching current 0.5 A Max. switching capacity 15 W Max. continuous current 0.5 A HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 295 Front panel and side panels: IP 65 Rear panel: IP 40 Mass 3.5 kg With Single-Pos stand: 3.6 kg With Duo-Pos stand: 3.8 kg With Multi-Pos stand: 4.5 kg With Multi-Pos holder: 4.1 kg HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 296: Product Dimensions And Mating Dimensions
All dimensions in the drawings are in millimeters. All dimensions in the drawings are in millimeters. 35.5 30.5 Figure 51: Dimensions of housing X112 X116 X100 Figure 52: Dimensions of rear panel of the product HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 297: Product Dimensions With Single-Pos Stand
19.3.2 Product dimensions with Duo-Pos stand ISO 7092-4 ISO 7092-4 ISO 7380-M4x8 Md = 2.6 Nm ISO 7380-M4x8 Md = 2.6 Nm 115.5 Figure 54: Product dimensions with Duo-Pos stand HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 298: Product Dimensions With Multi-Pos Stand
Md = 15 Nm max. 1 18.75 12.3 Figure 55: Product dimensions with Multi-Pos stand 19.3.4 Product dimensions with Multi-Pos holder Md = 15 Nm max. 1 Figure 56: Product dimensions with Multi-Pos holder HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 299: Index
Dragging........55 Dragging........ 55 overview......101 Duo-Pos........36 Holding........55 standard....... 101 operation........ 55 mounting........34 Tapping........55 Electrical specialist..... 25 Mounting Ground connection, 3-wire cable 52 Encoders Duo-Pos stand....... 36 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 300 User login......61 Password user types......118 changing....86, 116, 120 Qualified personnel....25 User ID........119 creating........ 119 Quick start........ 146 User interface After startup......63 Factory default setting... 63 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 301 68 User interface settings menu......73 Switch off menu....74 user login menu..... 72 User login........61 menu........72 Users deleting........ 121 Wiring switching inputs and outputs........46 Wizard........80 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 302: List Of Figures
Distance to go with position view with graphic positioning aid.......... 190 Image 43: Example of a program in the Program run operating mode..........196 Image 44: Image 45: Simulation window with contour view.................. 199 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 303 Image 53: Product dimensions with Single-Pos stand................297 Image 54: Product dimensions with Duo-Pos stand................297 Image 55: Product dimensions with Multi-Pos stand................298 Image 56: Product dimensions with Multi-Pos holder................298 HEIDENHAIN | POSITIP 8013 ACTIVE | Operating Instructions | 01/2018...
Page 304 DR. JOHANNES HEIDENHAIN GmbH Dr.-Johannes-Heidenhain-Straße 5 83301 Traunreut, Germany  +49 8669 31-0  +49 8669 32-5061 E-mail: info@heidenhain.de Technical support  +49 8669 32-1000 Measuring systems  +49 8669 31-3104 E-mail: service.ms-support@heidenhain.de NC support  +49 8669 31-3101 E-mail: service.nc-support@heidenhain.de NC programming ...

HEIDENHAIN POSITIP 8013 ACTIVE Operating Instructions Manual

Quick Links

Related Manuals for HEIDENHAIN POSITIP 8013 ACTIVE

Summary of Contents for HEIDENHAIN POSITIP 8013 ACTIVE