Siemens SINUMERIK 840D sl Function Manual page 15

7.11.1.3 TRAANG ....................................................................................................................................587
7.11.1.4 Chained transformations............................................................................................................588
7.11.1.5 Non transformation-specific machine data ................................................................................588
7.11.2 Signals .......................................................................................................................................589
7.11.2.1 Signals from channel .................................................................................................................589
8 Measurement (M5) ................................................................................................................................ 591
8.1 Brief description .........................................................................................................................591
8.2 Hardware requirements .............................................................................................................593
8.2.1 Probes that can be used ............................................................................................................593
8.2.2 Measuring probe connection......................................................................................................595
8.3 Channel-specific measuring.......................................................................................................600
8.3.1 Measuring mode ........................................................................................................................600
8.3.2 Measurement results .................................................................................................................601
8.4 Setting zeros, workpiece measuring and tool measuring ..........................................................602
8.4.1 Preset actual value memory and scratching..............................................................................602
8.4.2 Workpiece measuring ................................................................................................................603
8.4.2.1 Input values................................................................................................................................603
8.4.2.2 Measurement selection..............................................................................................................610
8.4.2.3 Output values .............................................................................................................................611
8.4.2.4 Calculation method ....................................................................................................................612
8.4.2.5 Units of measurement and measurement variables for the calculation.....................................615
8.4.2.6 Diagnostics.................................................................................................................................616
8.4.3 Types of workpiece measurement.............................................................................................617
8.4.3.1 Measurement of an edge (measurement type 1, 2, 3) ..............................................................617
8.4.3.2 Measurement of an angle (measurement type 4, 5, 6, 7)..........................................................621
8.4.3.3 Measurement of a hole (measurement type 8)..........................................................................624
8.4.3.4 Measurement of a shaft (measurement type 9).........................................................................627
8.4.3.5 Measurement of a groove (measurement type 12)....................................................................628
8.4.3.6 Measurement of a web (measurement type 13) ........................................................................631
8.4.3.7 Measurement of geo axes and special axes (measurement type 14, 15).................................632
8.4.3.8 Measurement of an oblique edge (measurement type 16)........................................................634
8.4.3.9 Measurement of an oblique angle in a plane (measurement type 17) ......................................635
8.4.3.10 Redefine measurement around a WCS reference frame (measurement type 18)....................639
8.4.3.11 Measurement of a 1-, 2- and 3-dimensional setpoint selection
(measurement type 19, 20, 21)..................................................................................................642
8.4.3.12 Measurement of an oblique angle (measurement type 24) .......................................................647
8.4.3.13 Measurement of a rectangle (measurement type 25)................................................................650
8.4.3.14 Measurement for saving data management frames (measurement type 26)............................652
8.4.3.15 Measurement for restoring backed-up data management frames (measurement type 27) ......653
8.4.3.16 Measurement for defining an additive rotation for taper turning (measurement type 28)..........654
8.4.4 Tool measuring ..........................................................................................................................655
8.4.5 Types of workpiece measurement.............................................................................................656
8.4.5.1 Measurement of tool lengths (measurement type 10) ...............................................................656
8.4.5.2 Measurement of tool diameter (measurement type 11).............................................................658
8.4.5.3 Measurement of tool lengths with zoom-in function (measurement type 22) ............................659
8.4.5.4 Measuring a tool length with stored or current position (measurement type 23).......................660
8.4.5.5 Measurement of a tool length of two tools with the following orientation: .................................661
8.5 Axial measurement (optional) ....................................................................................................672
8.5.1 Constraints .................................................................................................................................672
8.5.2 Measuring mode ........................................................................................................................673
8.5.3 Programming..............................................................................................................................674
8.5.4 Measurement results .................................................................................................................676
Extended Functions
Function Manual, 01/2008, 6FC5397-1BP10-3BA0
Contents
15