Table of Contents
Advertisement
Command
Advanced Configuration (continued)
Twisted Pair Protocol
Set input TP type
View input TP protocol
Set output TP protocol
View output TP protocol
KEY:
X!
= TP input
X6&
= DTP protocol setting
DTP Remote Power Parameters
ATTENTION:
•
Ensure that the correct remote DTP power setting is used. Sending DTP2 power to a DTP (series 1) endpoint can
result in hardware damage. Enable DTP2 power only to a compatible DTP2 endpoint.
•
Assurez-vous de bien régler l'alimentation DTP à distance. L'envoi d'une alimentation DTP2 à un point de connexion
DTP (ancienne gamme) peut provoquer des dommages matériels. Assurez une alimentation DTP2 uniquement vers un
point de connexion DTP2 compatible
Set input remote power
View input remote power
Set output remote power
View output remote power
NOTE:
The remote power state for HDBT and XTP modes is forced to Off (
the unit is not in DTP mode result in an
KEY:
X!
= TP input
X6^
= DTP remote power status
Resets
System reset (soft reset)
Absolute system reset
Absolute system reset, retain
IP settings
DTP2 CrossPoint 82 Scaling Presentation Matrix Switchers • SIS Configuration and Control
ASCII Command
Response
(Host to Switcher)
(Switcher to Host)
E
X!
X6&
}
I
*
HDBT
HdbtI
E
X!
}
X6&]
I
HDBT
E O 2
X6&
}
*
HDBT
HdbtO
E O 2
}
X6&]
HDBT
7
= DTP2/XTP input 7
0
= DTP format (default)
2
= HDBaseT format (output only)
E
X!
X6^
}
I
*
RPWR
RpwrI
E
X!
}
X6^]
I
RPWR
2
E
X6^
}
O
*
RPWR
RpwrO
2
E
}
X6^]
O
RPWR
E14
(Not valid for current configuration) error message.
7
= DTP2/XTP input 7,
0
= No remote power (default)
1
= DTP – 12 VDC
2
= DTP2 – 48 VDC
E ZXXX }
Zpx ]
E
}
]
ZQQQ
Zpq
E
}
]
ZY
Zpy
Additional Description
X!
X6&]
*
Set the TP protocol for input
X!
(
can be
View current TP protocol setting for input
X!
.
X@
X6&]
Set the TP protocol for DTP2/XTP/HDBT
*
Output 2 to
View TP protocol setting for output 2.
8
= DTP2/XTP input 8
1
= XTP format
X!
X6^]
*
Set the remote power on input
X!
(
can be
View remote power setting for input
2
X6^]
*
Set the remote power for output 2 to
View remote power setting for output 2.
0
). Attempts to change the power setting while
8
= DTP2/XTP input 8
Reset all device settings to factory
defaults
Set all device settings plus DHCP and
the IP address to factory defaults.
DHCP =
192
168
.
This command also removes the initial
serial number passwords that are set
at the factory and resets them to no
password.
Same as absolute system reset
E
(
ZQQQ
subnet mask, gateway address, DHCP,
and port mapping are not reset.
X!
X6&
to
.
7
8
or
only.)
X6&
.
X!
X6^
to
7
8
or
only.)
X!
.
X6^
Off
, IP address =
254
254
.
.
.
}
) except that IP address,
.
.
80
Advertisement
Table of Contents
