Mitsubishi Electric MELSEC iQ-R-R00CPU User Manual page 823

No. Name
SM1213 Data logging setting No.1
Data logging end
SM1214 Data logging setting No.1
Data logging trigger
SM1215 Data logging setting No.1
After data logging trigger
SM1216 Data logging setting No.1
Data logging error
SM1217 Data logging setting No.1
Data logging data saving in
progress
SM1218 Data logging setting No.1
Logging data storage file
switching in progress
SM1219 Data logging setting No.1
Data logging file transfer
execution status flag
SM1220 Data logging setting No.2
to
SM1229
SM1230 Data logging setting No.3
to
SM1239
SM1240 Data logging setting No.4
to
SM1249
SM1250 Data logging setting No.5
to
SM1259
SM1260 Data logging setting No.6
to
SM1269
Data stored Details
Off: Not completed This relay switches to on when the data
On: Completed logging is completed. For continuous
logging, the corresponding bit switches to
on when writing reaches the maximum
number of storage files and data logging is
completed (with "Stop" set for the operation
at the time when the number of save files
exceeds the limit). For trigger logging, the
corresponding bit switches to on when data
collection for the specified number of
records has been completed followed by
writing into the SD memory card after the
trigger condition was satisfied. The bit also
switches to on when an error is generated
(except for data logging error caused by
online program change) during the data
logging execution.
OffOn:Triggered The system switches this relay to on when
the specified trigger condition is satisfied.
Off: Not post triggering • This relay switches to on once data
On: Post triggering logging triggering occurs. The ON state is
maintained even when the data logging is
completed. However, this relay is off when
the data logging is in suspend/waiting for
start without collection/stop mode
• This relay also switches to off when the
CPU module is moved from RUN to
STOP mode and therefore the data
collection is halted.
Off: No error • This relay switches to on when a data
On: Error logging function error is generated.
• This relay switches to off when the setting
is registered or by the stop command
from CPU Module Logging Configuration
Tool.
Off: Not in progress This relay turns on when data in the internal
On: In progress buffer is being saved in the SD memory card
or function memory with the data logging.
Off: Not in progress This relay switches to on when storage file
On: In progress switching is in progress.
Off: Not executed • This relay turns on at the start of the data
On: Being executed logging file transfer function or
transferring of data logging files to the
data memory.
• This relay turns off at the completion of
the data logging file transfer function or
transferring of data logging transfer files
to the data memory.
Same configuration as the Data configuration is the same as the
setting No.1 setting No.1 (SM1210 to SM1219).
Same configuration as the Data configuration is the same as the
setting No.1 setting No.1 (SM1210 to SM1219).
Same configuration as the Data configuration is the same as the
setting No.1 setting No.1 (SM1210 to SM1219).
Same configuration as the Data configuration is the same as the
setting No.1 setting No.1 (SM1210 to SM1219).
Same configuration as the Data configuration is the same as the
setting No.1 setting No.1 (SM1210 to SM1219).
Set by (setting timing) CPU
S (Status change)
S (Status change)
S (Status change)
S (Status change)
S (Status change)
S (Status change)
S (Status change)
Same configuration as the
setting No.1
Same configuration as the
setting No.1
Same configuration as the
setting No.1
Same configuration as the
setting No.1
Same configuration as the
setting No.1
Appendix 4 List of Special Relay Areas
*1
Rn
RnP
RnSF
*1
Rn
RnP
RnSF
*1
Rn
RnP
RnSF
*1
Rn
RnP
RnSF
A
*1
Rn
RnP
RnSF
*1
Rn
RnP
RnSF
*1
Rn
*1
Rn
*2
RnP
*2
RnSF
*1
Rn
*2
RnP
*2
RnSF
*1
Rn
*2
RnP
*2
RnSF
*1
Rn
*2
RnP
*2
RnSF
*1
Rn
*2
RnP
*2
RnSF
APPX
821