Siemens SIPROTEC 4 User Manual page 643

Addr. Parameter
7001 FCT 50BF
7004 Chk BRK CONTACT
7005 TRIP-Timer
7006 50BF PICKUP
7007 50BF PICKUP IE>
7008 50BF-2 Delay
7101 FCT 79
7103 BLOCK MC Dur.
7105 TIME RESTRAINT
7108 SAFETY 79 ready
7113 CHECK CB?
7114 T-Start MONITOR
7115 CB TIME OUT
7116 Max. DEAD EXT.
7117 T-ACTION
7118 T DEAD DELAY
7127 DEADTIME 1: PH
7128 DEADTIME 1: G
7129 DEADTIME 2: PH
7130 DEADTIME 2: G
7131 DEADTIME 3: PH
7132 DEADTIME 3: G
7133 DEADTIME 4: PH
7134 DEADTIME 4: G
7135 # OF RECL. GND
7136 # OF RECL. PH
7137 Cmd.via control
SIPROTEC 4, 7SJ62/64, Manual
C53000-G1140-C207-8, Edition 08.2016
Function C Setting Options
50BF BkrFailure OFF
ON
50BF BkrFailure OFF
ON
50BF BkrFailure 0.06 .. 60.00 sec; ∞ 0.25 sec
50BF BkrFailure 1A 0.03 .. 20.00 A
5A 0.15 .. 100.00 A
50BF BkrFailure 0.03 .. 20.00 A
50BF BkrFailure 0.06 .. 60.00 sec; ∞ 0.50 sec
79M Auto Recl. OFF
ON
79M Auto Recl. 0.50 .. 320.00 sec;
0
79M Auto Recl. 0.50 .. 320.00 sec
79M Auto Recl. 0.01 .. 320.00 sec
79M Auto Recl. No check
Chk each cycle
79M Auto Recl. 0.01 .. 320.00 sec;
∞
79M Auto Recl. 0.10 .. 320.00 sec
79M Auto Recl. 0.50 .. 1800.00 sec;
∞
79M Auto Recl. 0.01 .. 320.00 sec;
∞
79M Auto Recl. 0.0 .. 1800.0 sec; ∞ 1.0 sec
79M Auto Recl. 0.01 .. 320.00 sec
79M Auto Recl. 0.01 .. 320.00 sec
79M Auto Recl. 0.01 .. 320.00 sec
79M Auto Recl. 0.01 .. 320.00 sec
79M Auto Recl. 0.01 .. 320.00 sec
79M Auto Recl. 0.01 .. 320.00 sec
79M Auto Recl. 0.01 .. 320.00 sec
79M Auto Recl. 0.01 .. 320.00 sec
79M Auto Recl. 0 .. 9
79M Auto Recl. 0 .. 9
79M Auto Recl. (Einstellmöglich-
keiten anwendung-
sabhängig)
Functions, Settings, Information
Default Setting Comments
OFF 50BF Breaker Failure
Protection
OFF Check Breaker contacts
TRIP-Timer
0.10 A 50BF Pickup current
threshold
0.50 A
0.10 A 50BF Pickup earth current
threshold
Delay of 2nd stage for
busbar trip
OFF 79 Auto-Reclose Function
1.00 sec AR blocking duration after
manual close
3.00 sec 79 Auto Reclosing reset
time
0.50 sec Safety Time until 79 is
ready
No check Check circuit breaker
before AR?
0.50 sec AR start-signal monitoring
time
3.00 sec Circuit Breaker (CB)
Supervision Time
100.00 sec Maximum dead time
extension
∞ sec Action time
Maximum Time Delay of
Dead-Time Start
0.50 sec Dead Time 1: Phase Fault
0.50 sec Dead Time 1: Ground
Fault
0.50 sec Dead Time 2: Phase Fault
0.50 sec Dead Time 2: Ground
Fault
0.50 sec Dead Time 3: Phase Fault
0.50 sec Dead Time 3: Ground
Fault
0.50 sec Dead Time 4: Phase Fault
0.50 sec Dead Time 4: Ground
Fault
1 Number of Reclosing
Cycles Ground
1 Number of Reclosing
Cycles Phase
none Close command via
control device
F.2 Settings
643