Wireless Hott System; Preparing For Training Mode; Preparing Teach And Pupil Transmitters - GRAUPNER mz-24 Pro Programming Manual

Wireless HoTT system

The trainer system of the mz-24 HoTT Pro transmitter
can also be operated remotely. As described below,
the TEACH transmitter is bound to a PUPIL transmit-
ter. This configuration is possible between two trans-
mitters that are available in the "Trainer" menu using
the "BIND" option (see the figures in this section).

Preparing for training mode

TEACH transmitter
The training model must be programmed with all its
functions including trimming and any mixed functions
in a model memory of the HoTT TEACH transmitter.
Attention
The model provided for training must therefore be
completely controllable by the TEACH transmitter
and remains also during the trining phase con-
nected to the teacher transmitter.
Notice
Regardless of the firmware version of the teacher
transmitter, the training model MUST ALWAYS be
linked to the pupil transmitter in the case of a type
mx-10 HoTT pupil transmitter with firmware version V
1a20. In addition, it is absolutely essential for correct
schooling that both option buttons in the
OFF" line of the "TX ctl" menu be set to
model memory of the teacher transmitter used for the
training. In other words, there is no link to a receiver in
this model memory under either RX1 or RX2.
PUPIL transmitter
With Graupner HoTT transmitters of the series "
"mx" or "mz", it is best to assign the model name
"PUPIL" to a free model memory activated with the
required model type and adapt the control arrange-
ment (mode 1 ... 4) and "THR min or PITC min front/
rear" to the PUPIL's preferences.
All other settings as well as all mixing and coupling
functions are made in the TEACH transmitter and are
transmitted by the TEACH transmitter to the receiver.
Observe the standard conventions in the model types
"motor airplane" and "glider" so as in the model type
"helicopter" when assigning control functions:
Channel Function
1 Motor/airbrake or pitch
2 Aileron or Roll
3 Elevator or Nick
4 Rudder or Yaw
If you wish to assign other
TEACH transmitter in addition to the functions of the
two control sticks (1 ... 4), assign control elements
to the inputs in the "Control assignment" menu of
"BIND ON/
the PUPIL transmitter that correspond to the released
OFF in the
Functions or control inputs
menu of the TEACH transmitter.
Notice
If you forget to assign a control in the PUPIL
transmitter, the relevant servo(s) remain in middle
position after transferring control functions to the
mc ",
PUPIL transmitter.

Preparing TEACH and PUPIL transmitters

After binding the training model to the PUPIL trans-
mitter , also turn on the TEACH transmitter and open
the "Trainer" display on the two transmitters:
The above figure shows the original layout of the sub-
menu.
Notice
PUPIL transmitter
Control functions to the
Check the display and modify it so that it corresponds
with the above screen-shot.
TEACH transmitter
You can transfer up to twelve
5... 12 in the "Trainer"
mz-24 HoTT Pro TEACH transmitter, to the PUPIL
transmitter, either individually or in any desired com-
bination.
Notice
sub-menu when the trainer connection is turned off.
BACK Trainer SERVO
CH 1. TEACH CH 7. TEACH CTL
CH 2. TEACH CH 8. TEACH NULL
CH 3. TEACH CH 9. TEACH BIND
CH 4. TEACH CH 10. TEACH OFF
CH 5. TEACH CH 11. TEACH TYPE
CH 6. TEACH CH 12. TEACH RF
Note that the value field under "TYPE" at the bot-
tom right of the display is set to RF
PUPIL and TEACH transmitter.
Function inputs
It does not matter which specific Controls
signed to the inputs to be transferred to the PU-
PIL. They can only be assigned in the
Function menu | general - Trainer
in both the
,of an
are as-
Set"
"CTL
145