Binding Several Receivers Per Model; "Binding" Transmitter And Receiver - GRAUPNER mz-24 Pro Programming Manual

Binding several receivers per model

If desired, several receivers per model can be bound.
In the related programs of the mz-24 HoTT Pro re-
ceivers, you can directly manage up to two receivers
bound to each active model memory and use a menu
to distribute the 12 transmitter control channels be-
tween the two receivers (see below in this section).
First bind the two receivers one by one as described
below.
During subsequent operation, only the receiver es-
tablishes a telemetry link to the transmitter that was
either last bound to the active model memory, or was
selected in the "RECEIVER SELECT" line in the "Te-
lemetry", for example:
BACK Telemetry
RX SELECT RX1 ALWAYS
>>
SETTING & DATA VIEW
SENSOR >>
>>
RF STATUS VIEW
>>
VOICE TRIGGER
Telemetry sensors eventually installed in the model
have to be connected to this receiver, because the
transmitter will indicate only the values coming from
the back channel of the receiver selected in this line.
The second receiver (and all other receivers) run inde-
pendently at the same time in slave mode.
Tip
• To RX2 can only be bound a receiver if there is al-
ready a bound receiver on
• If for any reason the binding of the
also the RX1
a receiver to
of course before a new binding can be attempted
to RX2 .

"Binding" transmitter and receiver

Turn off the power supply to your receiver at this
time (at the latest).
• GR-16 and GR-24 and similar receivers
The red LED flashes on the receiver.
Hold down the SET button on the receiver until, af-
ter about 3 seconds, the flashing red LED flashes
red/green for around 3 seconds. Then release the
INC
SET button on the receiver. As long as the LED is
RES
flashing red/green, the receiver is in binding mode.
DEC
Within this 3 second window, start binding the re-
ceiver to the current model memory by touching
RX1
the button in the "BIND ON/OFF" line with a
finger or the provided stylus, for example.
BACK
BIND ON/OFF
TX OUT SET
RF ON/OFF
RANGE TEST
DSC OUTPUT
The writing in the button will change from "OFF"
to "CHK":
RX1 .
RX2 should fall,
will be set to OFF . The binding of
RX1 has to be renewed firstly and
TX ctl
RX1 RX2
OFF OFF
SET SET
Touch
OFF NORMAL
RF TYPE
OFF
99sec
PPM10 OFF
AUTOLOG
BACK TX ctl
RX1 RX2
CHK OFF
BIND ON/OFF
TX OUT SET SET SET
OFF
RF ON/OFF RF TYPE
OFF
RANGE TEST 99sec
DSC OUTPUT PPM10 AUTOLOG
Binding is complete once (within a period of ap-
proximately 10 seconds) the flashing red receiver
LED shines green continuously. Your model mem-
ory/receiver combination is now operable. At the
same time, instead of CHK, an abbreviation of the
receiver type such as 12CH appears for the re-
ceiver GR-24 HoTT receiver which comes stan-
dard:
BACK TX ctl
RX1 RX2
12CH OFF
BIND ON/OFF
SET SET
TX OUT SET
ON
RF ON/OFF RF TYPE
OFF
RANGE TEST 99sec
PPM10 AUTOLOG
DSC OUTPUT
At the same time, RF transmission is turned on
(see the line "RF ON/OFF" in the following display).
If the red receiver LED continues to flash for more
than 10 seconds, the binding process was unsuc-
OFF
cessful. At the same time,
the line "BIND ON/OFF". Change the positions of
the associated antennas and try the entire proce-
dure again.
• GR-12L and similar receivers
The red LED on the receiver shines.
Hold down the SET button on the receiver until,
after about 3 seconds, the red LED goes dark for
around 3 seconds. Then release the SET button on
Base menu - Transmitter setting
NORMAL
OFF
NORMAL
OFF
appears again in
69