GRAUPNER mz-24 Pro Programming Manual page 41

BACK STARLET
01 STARLET
02
BEAVER
03 GRAUBELE
04
MODEL NAME 4
05 MODEL NAME 5
06 MODEL NAME 6
... and then touch NO to terminate the process or
YES to switch the model ...
BACK STARLET
01
STARLET
02 BEAVER
03 GRAUBELE
04 MODEL NAME 4
CHANGE
Touch
MODEL
MODEL NAME 5
05
YES
NO
06 MODEL NAME 6
... "Please wait!!" appears for about 1 second:
BACK STARLET
01 STARLET
02 BEAVER
03 GRAUBELE
04 MODEL NAME 4
MODELL
Please
WECHSEL
05 MODEL NAME 5
wait!
J
06 MODEL NAME 6
• If a receiver is already bound to the selected model
memory, in case of inactive Thr.POS warning the
RF module of the transmitter will be switched on
and the display changes to the base display with a
warning window:
NEXT
SEL
NEW
Touch
IMP.M
EXP.M
RES
CPY
So as it happens when you switch the transmitter
on, you now have the option of waiting a few sec-
onds until the display disappears automatically or
NEXT
maintaining the RF transmissions by manually tap-
SEL
ping the
NEW
ping the
IMP.M
• If no receiver is bound to the selected model mem-
EXP.M
ory, the display also changes to the base display
RES
with the visible window. The RF module remains
CPY
then switched off and in place of the "RF ON/OFF"
warning it will appear "No receiver bound to TX!":
NEXT
SEL
NEW
IMP.M
EXP.M
RES
N
CPY
Tapping on the
sub-menu »TX ctl« of the basis menu, where you
can bind your receiver in the line "Bind ON/OFF"
...
000% 000%
Warning
4.2V
Thr.HOLD Thr.CUT
000:00.0
000 000
Thr.POS PHASE
mz
0:01:23 000:00.0
Fail Safe not set
RC Signal
M - 1
000 000
PHASE 1
Please select RF ON/OFF
MODEL NAME 1
ON OFF
BATT TIME 00: 01: 23
000 000
ON button, or switching them off by tap-
OFF button.
000% 000%
Warning
4.2V
Thr.HOLD Thr.CUT
000:00.0
000 000
Thr.POS PHASE
mz
000:00.0
0:01:23
Fail Safe not set
M - 1
000 000
PHASE 1
No receiver bound to TX!
MODEL NAME 1
SET
BATT TIME 00: 01: 23
000 000
SET
button directly opens the
BACK TX ctl
RX1 RX2
OFF OFF
BIND ON/OFF
TX OUT SET SET SET
OFF
RF ON/OFF RF TYPE
OFF
RANGE TEST 99sec
DSC OUTPUT PPM10 AUTOLOG
... or by touching the related BACK
you will be brought directly to the base display of
the transmitter.
NEU
Tips
• To reach up for model memories with number
NEXT
higher than 06, tap on the
right upper side of the display (next page).
• You can change between already occupied model
memories through SEL .
As described above under SEL
model, select a free model memory or model mem-
ory that has already been assigned but is no longer
required. Tap on the NEW button on the right side
of the display:
BACK STARLET
01 STARLET
02 BEAVER
03 GRAUBELE
04 MODEL NAME 4
05 MODEL NAME 5
06 MODEL NAME 6
NEW
After tapping on a selection window will appear
in which you can select one option between manual
or assisted programming of the new model so as
to interrupt the procedure:
Base menu - Model selection
NORMAL
OFF
button until
(create new model)
button on the
, to set up a new
NEXT
SEL
NEW
IMP.M
Touch
EXP.M
RES
CPY
NO
41