• "Offset" Line - GRAUPNER mz-24 Pro Programming Manual

BACK PHASE 1 CTL Set
CH 5. NULL 000% +100% +100%
CH 6. SL 2 000% +100% +100%
CH 7. NULL 000% +100% +100%
CH 8. NULL 000% +100% +100%
OFFSET
CTL – Travel +
... AND set "ACT" in the sub-menu
the function menu to INH ...
BACK PHASE 1 Flap Set
ACT INH CTL ON
AILE1 AILE2
000%
RATE A 000%
RATE B 000% 000%
... or a switch assigned in the same line is
switched OFF and in this way in the value field on
OFF
the right near "ACT" indicates
BACK
PHASE 1 Flap Set
ACT OFF CTL SW 6
AILE1 AILE2
RATE A 000% 000%
000% 000%
RATE B
... THEN determine the value input in the RATE A
/ B line the grade of deflection of the flap through
the selected control.
To change a previously input value, touch the cor-
responding value field, for example:
SERVO BACK
FLAP
NEXT
INC
RES RATE A
DEC
RATE B
OFFSET
"Flap set" of The color of the field switches from black to blue:
BACK
SERVO
FLAP
NEXT
INC
RATE A
RES
RATE B
DEC
OFFSET
Then, in the active (blue) value field, press
crease the current value within a range of ±125%
and – to reduce it, for example:
, ...
BACK
SERVO
FLAP
NEXT
INC
RATE A
RES
RATE B
DEC
OFFSET
Use the same procedure with the value for the
downward deflection of the left flap (RATE B) and
for the values of the right flap and for any second
flap pair. Symmetrical and asymmetrical values are
possible.
RES
Touch the
the blue (and hence active) field to the default val-
ue.
PHASE 1 Flap MIX SERVO
Touch
INC
FLAP1 FLAP3 FLAP4 FLAP2
+100% +100% +100% +100% RES
DEC
+100% +100% +100% +100%
000% 000% 000% 000%
PHASE 1 Flap MIX SERVO
INC
FLAP1 FLAP3 FLAP4 FLAP2
+100% +100% +100% +100% RES
DEC
+100% +100% +100% +100%
000% 000% 000% 000%
+ to in-
SERVO
PHASE 1 FLAP MIX
FLAP1 FLAP3 FLAP4 FLAP2 INC
+025% +100% +100% +100% RES
+100% +100% +100% +100% DEC
000% 000% 000% 000%
button to reset a changed value in
• "OFFSET" line
In this line, set the phase-specific positions for all
of the flaps in the respective model. This allows
you to set the positions that the individual flaps are
to assume for each phase.
The adjustment range of ±100% allows the flaps
to be moved to the desired position independent
of the rotational direction of the flap servos, for ex-
ample:
BACK PHASE 1 FLAP MIX
FLAP
FLAP1 FLAP3 FLAP4 FLAP2
RATE A +025% +030% +030% +025%
RATE B +025% +030% +030% +025%
OFFSET -011% -022% -022% -011%
Notices
• The available setting options depend on
the number of flaps selected in the basic
settings of the model memory.
• The flap offset of the flaps is set, complete-
ly independently from the used described
in connection with the left "ACT", in the
phase trimming described in the following
"Flap Sett" section.
• The corresponding offset-positions of the
first aileron pair have to be set, according
to the phase, in the "CH5" line and the
eventually required second flap pair has to
be set in the "CH12" line of the
sub-menu:
Function menu | Airplane models - Flaps mixer
SERVO
INC
RES
DEC
"CTL Set"
193