Pupil Transmitter Settings - GRAUPNER mz-24 Pro Programming Manual

BACK Trainer
CH 1. PUPIL CH 7. TECH
CTL
CH 2. PUPIL CH 8. TECH SW 8
CH 3. PUPIL CH 9. TECH BIND
CH 4. PUPIL CH 10. TECH OFF
CH 5. TECH CH 11. TECH TYPE
CH 6. TECH CH 12. TECH RF
Since at this early point in the trainer system pro-
gramming an operable PUPIL transmitter will not be
connected to a TEACH transmitter, the transmitter
immediately reacts with acoustical alarms to switches
connected during the switch assignment. At the same
time, a warning message flashes every second at the
top left in the transmitter's main display (see the figure
at the end of the section, "Wireless HoTT system").
Open the switch that has just been assigned.
First, in the value field under "TYPE", change the de-
RF DSC L
fault to in the bottom line to the right in
order to switch the DSC connection to "signal input":
BACK Trainer
CH 1. PUPIL CH 7. TEACH
CTL
CH 2. PUPIL CH 8. TEACH SW 8
CH 3. PUPIL CH 9. TEACH BIND
CH 4. PUPIL CH 10. TEACH OFF
CH 5. TEACH CH 11. TEACH TYPE
CH 6. TEACH CH 12. TEACH DSC T
If the connection to the PUPIL is NOT made with a
two-pin DSC socket but rather a three-pin T/P jack
by Graupner, for a correct connection to a PUPIL
transmitter, the modulation type PPM(10, 16, 18 or
24) must be set in the PUPIL transmitter independent
of the type of modulation used in the TEACH trans-
mitter.
142 Function menu | general - Trainer

PUPIL transmitter settings

SERVO
The model to be controlled by the PUPIL must be pro-
grammed with all its functions including trimming and
any mixed functions in a model memory of TEACH
transmitter. If applicable, the HoTT receiver of the rel-
evant model must also be bound to the TEACH trans-
mitter. In principle, a HoTT PUPIL transmitter can be
connected to a TEACH transmitter with the classic
35/40 MHz range since the required PPM signal re-
quired by the TEACH transmitter is normally always
applied to the DSC socket of a HoTT transmitter.
Almost any transmitter from the past and current
Graupner product line with at least 4 control functions
can be used as the PUPIL transmitter. The PUPIL
transmitter should however be equipped with the cur-
rent connection module for PUPIL transmitters. The
module should be connected to the transmitter board
in accordance with the provided installation instruc-
tions.
The specified cable is used to connect to the TEACH
transmitter (see the next two pages).
SERVO
More information can be found in the main Graupner
FS catalogue and on the Internet at
de.
The control functions of the PUPIL transmitter must
act directly on the control channels without any inter-
mediate mixers, i.e. the receiver outputs
With transmitters of the series "mc", "mx" or "mz",
it is best to assign the model name "PUPIL" to a free
model memory activated with the required model type
("wing" or "heli"), and adapt the control arrangement
(mode 1 ... 4) and "THR min or PITC min front/rear" to
the PUPIL's preferences. All other settings as well as
mixing and coupling functions are made in the TEACH
transmitter and are transmitted by the TEACH trans-
mitter to the receiver.
With transmitters of the "mz- 18/24" series, also
touch the value field under "TYPE" in the bottom line
of the "T/P" sub-menu at the bottom right of the dis-
play to switch it to
DSC transmitter connection to "signal output":
BACK
CH 1.
CH 2.
CH 3.
CH 4.
CH 5.
CH 6.
With a mx-20 HoTT,
or mc-32 HoTT PUPIL transmitter, adapt the mod-
ulation types to the number of control channels to be
transferred in the line "DSC OUTPUT" of the "BASE"
menu For example, the signal package with modula-
tion type "PPM10" only contains control channels 1
... 5, and channels 6 and higher are not included. In
order for the PUPIL to use one or more of channels
5 and above, select one of the modulation types that
includes the required channels. If in addition PUPIL
www.graupner.
mode is to be used with an existing model memory
instead of a newly initialized one in one of the afore-
mentioned transmitters, make sure to enter "HoTT" in
the "Module" line of the "BASE" menu. Otherwise, the
PPM signal at the DSC socket may be inverted.
If you wish to assign other control functions to the
TEACH transmitter in addition to the functions of the
two control sticks (1 ... 4), assign control elements
to the inputs in the "Control assignment" menu of
the PUPIL transmitter that correspond to the released
function inputs 5... 12 in the "Trainer" menu of the
TEACH transmitter.
DSC S
and hence switch the rear
SERVO
Trainer
PUPIL CH 7. TEACH CTL
PUPIL CH 8. TEACH SW 8
PUPIL CH 9. TEACH BIND
PUPIL CH 10. TEACH OFF
TEACH CH 11. TEACH TYPE
TEACH CH 12. TEACH DSC P
mc-16 HoTT, mc-20 HoTT