"Pitch Curve"; Basic Operating Steps - GRAUPNER mz-24 Pro Programming Manual

WIZ. PHASE 1 D/R,EXP
CH ROLL
Touch
D/R +100% +100%
EXP 000% 000%
CTL NULL
SYM OFF
Analogous to the previously described displays,
touch the corresponding option field to change a cur-
rent value, and raise or lower the value by touching
the + and – buttons at the right side of the display
the appropriate number of times.
The adjustment range is ±125 % in the "D/R" line and
±100 % in the "EXP" line.
Touch the RES button to reset a changed value in a
blue (active) value field to the default value.
If you desire a switch between two variants, you can
assign a switch or a control in the CTL line, as de-
scribed in the "Control and switch
graph.
Once all you have adjusted all the DR/EXPO func-
tions, touch again the WIZ. button at the top left to
switch to the next adjustment phase:

"Pitch curve"

In the "PITCH MIN." line of this display you can adjust
to your preferences the movement direction of the
pitch stick so as, through the remaining options, the
pitch curve.
1. Line "PITCH MIN."
Through this option you can easily reverse the
control direction of the pitch control stick from
the standard pre-set position "pitch min back" to
"pitch min forward", and vice versa, by tapping on
BACK FORWARD
the or button in the "Pitch min"
line:
48 Base menu - Model selection
INC
RES
DEC
After tapping on this button it will appear a safe-
ty query:
Touch NO
on YES confirms the procedure and reverses the
assignment" para-
movement direction of the pitch stick WITHOUT
any visual changes in the display:
2. Setting the pitch curve
Tip
After having completed the program assisted model
programming and the setting of the phases in the
"PHASE" sub-menu of the functions phase specific
menus can be programmed.
WIZ. NORMAL PIT.CRV
BACK TRIM
Pitch min.
Curve OFF
Touch
INC
IN –100%
OUT –100%
DEC
POINT L –100%
ST OFF X-axis Y-axis ENT
WIZ. NORMAL PITCHK
Pitch min. BACK TRIM
KURVE AUS
Warning
SURE?
EIN –100% INC
AUS –100%
YES NO
POINT L –100% DEC
ST OFF X-axis Y-axis ENT
to terminate the procedure. Tapping
WIZ. NORMAL PIT.CRV
Pitch min. FORWARD TRIM
Curve OFF
IN –100% INC
OUT –100%
DEC
POINT L –100%
ST OFF X-axis Y-axis ENT

Basic operating steps

• Button ST OFF / ST ON
Touch this button to turn the graphic and nu-
meric display of the control stick position on
and off, for example:
WIZ. NORMAL PIT.CRV
Pitch min. FORWARD
Curve OFF
IN +050%
+050%
OUT
POINT ? 000%
ST ON X-axis Y-axis
With the control element (gas/pitch control
stick), a vertical green line is moved synchro-
nously in the graph between the two endpoints
"L" and "H". The momentary control stick po-
sition is also displayed numerically in the line
"IN"(put) (-100 % to +100 %). The intersection
of this line with the curve is identified as "OUT-
"(put) and can be varied at the support points
between -125% and +125%. The control sig-
nal which is changed in this way then affects all
of the following mixing and coupling functions.
• ENT button
Touch the button at the bottom right of the dis-
play to set up to 5 additional points between
the two endpoints "L" and "H".
In the following example, the control stick is ex-
actly between the middle and end of its path,
at +50% of the control path, and generates an
output signal that is also +50% due to the lin-
ear characteristic.
TRIM
INC
DEC
ENT